Need Help?
Call
The Control Knob with Clip is an OEM part for GE washing machines and dryers. This knob allows users to select and control various settings and cycles on their appliance with ease. Causes of a bad Control Knob with Clip can include constant use leading to wear and tear, accidental impacts that may crack or break the knob, or exposure to harsh cleaning agents that can cause the knob's material to degrade over time. Symptoms of a bad Control Knob with Clip include:
This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.
I first received the quality parts in less than 2 days. It took me 5 minutes to change out the timer and 2 of the minutes were finding where my fiancée put the Phillips head screwdriver. Unplug dryer first, remove top three screws from back panel. Pull old timer up and out, have new timer in hand and transfer one wire at a time. Once all wires are transferred, snap the new timer in its place. Replace your three screws, put knob on timer. Plug in dryer and test. Once completed, cleanup your... Read more
Burner won't heat or only inner ring works? This dual radiant element restores both heating zones on your cooktop. Moderate DIY with basic tools.
Replace 9" dual burner. Read more
The Hub Nut is an OEM part for GE washing machines. This component secures the inner tub to the drive mechanism, ensuring that it remains in place during the agitation and spinning cycles. This lock-down nut is reverse threaded, meaning that it is loosed by rotating it clockwise. For easier removal of the old nut, it is recommended to use the tub nut spanner wrench WX5X1325.
Symptoms of a bad Hub Nut include:
Causes of a bad hub nut can include corrosion due to exposure to water and detergent, improper initial installation, or loosening over time from the vibration and movement of the washing machine.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
I had never worked on a washing machine before but after watching the online videos I felt like I could do the repair. I was almost positive it was the Mode Shifter and Shaft Assembly that was bad. I could hear the bearing making a grinding noise when I turned the tub by hand. I ordered the part I needed plus additional parts that could be an issue later such as a drive belt, tub bearing, tub seal, tub nut, split ring, etc; Preventive maintenance that would keep from having to tear it all... Read more
Washer won't spin or shows flashing lights? This door lid lock ensures safe operation by securing the lid during cycles. DIY-friendly, 2-screw install.
Replaced the lock lid mechanism. Read more
Lower dishrack assembly for dishwasher bottom level. Holds plates, pots, and pans during wash cycles. Replace if rusted, cracked, or tines broken.
Replaced the upper and lower racks. AppliancePartsPro shipped the racks fast and they are a perfect fit. I think they're even a better, stronger design then the factory originals. Read more
Washer won't drain or leaves clothes soaking wet? This drain pump removes water from the tub after each cycle. Typical DIY repair takes 20-30 minutes.
I ordered a new pump on this website. They provided me with written directions as well as a video to follow along with on how to change the pump. As always it wasn't as easy as the video, but that was the mechanic no the tool! Great job on the service. Will order parts from here again. Read more
Seals the lint screen housing to prevent lint bypass into internal components. Replace if lint escapes or seal is worn. Confirm fit with your model.
Upon examination of the dryer, I noticed that the belt was intact, though a little worn and hard. However, I noticed that the belt had came of the idler pulley. So I put it back on and had the owners try it out on their next load of wash. It, once again failed to keep the drum turning. So I ordered a new belt and idler pulley (order # 8676164). I found it necessary to remove the drum, in order to change out the new pulley. However, while trying to reinstall the drum, we damaged some of the... Read more
Replacement roller and stud assembly for dishwasher racks. Installs on upper or lower rack to restore smooth gliding. Needed when rollers crack or studs break.
Ordered the clips that we easy to find on line. They can within a few days..and replaced them myself..didn't wait for my husband. Hardest part was getting the end caps off the metal rack to replace the rollers and clips. They fit in there spmehow. I used a screwdriver to get them out. Rest was a piece of cake Lol Read more
Burner cap assembly covers the burner head on gas cooktops and ranges. Replace cracked, stained, corroded, or missing caps to restore appearance.
I ORDERED NEW CAPS AND PUT THEM ON. Read more
This 8-inch drip bowl installs under your range burner to catch grease and spills. Replace if yours is rusted, cracked, warped, or heavily stained.
Ordered all the parts Read more
The Run Capacitor is an OEM part for GE refrigerators. It plays a crucial role in the refrigerator's cooling system by providing the necessary start and run voltage to the compressor. Without a properly functioning run capacitor, your refrigerator may struggle to maintain the desired temperature, leading to spoiled food and inefficient energy use. Causes of a bad run capacitor include electrical surges, wear and tear over time, or overheating due to a malfunctioning refrigerator compressor or poor ventilation. Symptoms of a bad Run Capacitor include:
We replaced the main circuit board and the LED started to work and the condenser fan worked, but all we had were relay clicking sounds, but no cooling. The compressor had become so hot trying to work when the main circuit board was amiss, that it had popped the over temperature sensor on its side. As some one point out, if you remove the PTC+OLP assembly with the capacitor on it, and shake it, you will hear a rattle inside---and that is bad. We ordered a second round of parts from... Read more
Replace your washer drive belt if the drum won't spin or agitate. Connects motor to drum for proper washing cycles. Confirm fit with your model number.
Ordered new transmission, nut, split washer and spanner wrench to do the install. very straight forward fix after watching the video. spanner wrench is a must or the correct large socket with an impact driver. it was corroded on pretty well let the liquid wrench work for a while and then beat it off. approximately 2 hours to do to fix, spent some time cleaning stuff up also though. washer was 12 years old and debated scrapping it and getting a new one but then it would not match the dryer. ... Read more
Replacement dairy door for refrigerator. Snaps into door to create covered compartment for butter and cheese. Needed when original is cracked or broken.
Just enter the appliance model and the all the parts are pictured! Really easy! Read more
The Door Interlock Switch is an OEM part for GE microwaves. It ensures the safety of the microwave by preventing the appliance from operating while the door is open. This switch is part of a microwave's safety mechanism, which includes multiple interlock systems designed to stop the generation of microwaves immediately once the door is opened, thereby protecting users from exposure to microwave radiation.
Signs that it's time to replace your door interlock switch include the microwave not starting or stopping unexpectedly, the microwave continuing to operate with the door open, or a failure to heat food even though the appliance seems to be running.
Symptoms of a bad Door Interlock Switch include:
Removed and replaced 3 door switches and mounting bar that holds switches plastic gets brittle with age and each switch comes out slightly different from each other, the chances of breaking a mounting pin is very easy. care should be taken when snapping mounting bar back into place to insure top latch and bottom latch locate properly insure bar is proper aligned when tightening screws their is free play in mounting bracket that could affect door properly engaging switches. NOTE that their are... Read more
Oven not heating or baking unevenly? A failed bake element is the likely cause. This DIY repair typically takes 15-30 minutes with basic tools.
I wanted to get the upper oven baking element replaced; it hasn't been working for a few months. This double oven has had two other issues, there is a fan that comes on to cool the electronics panel, That fan has made excessive noise and it operates for 2-3 hours after the oven turns off. The other problem with the oven is the Self-Cleaning feature runs for about 15-30 minutes and then turns off with an error code. I've had a local appliance repair person in to address the error code and... Read more
Protective cover for your dryer's lint trap that prevents objects from entering the vent. Replace if cracked or broken. Snaps into place. Confirm fit.
Just snapped and slid it into place, very simple. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.