Parts for Lg LFXS28968S/11: Ice Maker & Ice Bin Parts

The Handle Mounting Stud is an OEM replacement part for LG refrigerator doors. It provides a sturdy mounting point for the door handle assembly. Reliable handle connection and support is crucial for dependable door function and access. 

Causes of a faulty stud can include damage from excess weight or impact over time rendering the stud loose or unstable.

Symptoms of a bad stud include:

• Loose or sagging door handle  
• Difficulty opening and closing the refrigerator door  
• Potential for the handle to detach completely
• Safety concerns if the handle connection fails

This OEM LG replacement stud is also compatible with Sears/Kenmore models. 

This funnel assembly directs detergent and rinse aid from the dispenser into the dishwasher wash chamber for proper cleaning. Replaces a cracked or clogged funnel to restore reliable dispensing and reduce leaks or pooling. What it does:

• Channels detergent and rinse aid from the dispenser to the wash chamber for even distribution
• Prevents splash-back and reduces the chance of detergent clumping or not reaching the wash arms
• Helps stop minor leaks or water pooling around the dispenser area when the original funnel is damaged
• Keeps the dispenser pathway clear so the detergent dissolves and dispenses as intended

• One replacement funnel assembly

• Disconnect power to the appliance before starting any repair
• Turn off the water supply and drain standing water from the unit if applicable
• Remove the dispenser bezel or control panel per OEM instructions to access the funnel; handle plastic clips and tabs gently to avoid breakage
• After installation, run a short cycle to check for leaks

The Drain Pipe Assembly is an OEM replacement part for LG refrigerators. It is a plastic tubing system that collects and removes liquid condensation from evaporator coils. Proper drainage is crucial to minimizing frost buildup and ensuring optimal cooling of food storage areas. 

Symptoms of a bad drain pipe assembly include:

• Excessive frost or ice accumulation inside the refrigerator
• Puddling or leaks detected near evaporator housing
• Slow draining allowing water to pool versus emptying fully
• Cracks or breaks in the tubing prevent complete fluid removal

Causes are typically mineral sediment clogging drainage paths or deteriorating plastic from constant use. This OEM LG replacement pipe restores reliable condensate removal to maintain peak efficiency.

This OEM LG part is also compatible with Sears/Kenmore. 

The Leveling Leg is an OEM part for LG refrigerators. It is one of the four legs at the bottom corners that elevate and provide stability to the entire appliance.

Causes of failure can be broken mounting points that no longer provide secure elevation, full compression of the built-in cushioning, or damage from impact on an unlevel floor.

Symptoms of a faulty leveling leg include:

• Excessive shaking or vibrating of the refrigerator
• Door alignment issues where doors are difficult to open or close fully
• Visible leaning or misalignment of the refrigerator cabinet

This OEM LG part is also compatible with some Kenmore models.

The Freezer Tray is an OEM part for LG refrigerators. It provides an open, flexible surface area within the freezer compartment for storing and organizing frozen foods. The freezer tray's material and rail design also efficiently facilitate airflow to maintain sub-freezing temperatures throughout. 

Symptoms of a faulty freezer tray include:

• Cracks or breaks that compromise structural integrity
• warping or pitting which prevents proper sealing 
• uneven temperatures due to airflow disruption

Causes of a bad freezer tray can include impact damage over time, continuous door openings and closings leading to fatigue, and temperature fluctuations compromising the material.

This OEM LG part is also compatible with Sears/Kenmore refrigerator models.

A small protective cap that covers and protects a component connection or opening from dirt and moisture, helping maintain proper function and prolong component life. Simple replacement when the original cap is cracked, missing, or worn. What it does:

• Covers exposed fittings, terminals, or openings to keep out debris and moisture
• Helps prevent leaks or contamination at the sealed connection
• Restores a secure fit when the original cap is cracked, split, or degraded
• Commonly used where a small, removable protective seal is required

• Inspect mating surface and surrounding gasket/seal before installing; replace other damaged parts as needed
• Press the cap firmly into place until fully seated; no special tools usually required
• Wear gloves and disconnect power or water supply if working near energized or pressurized components

This roller assembly supports and guides a sliding rack, shelf, or drawer so it rolls smoothly along its track. Replacing a worn roller restores easy, even movement and helps prevent sticking, wobbling, noise, or the rack/drawer jumping off the rail.

• Provides rolling support for a sliding component on its rail
• Maintains alignment to reduce binding and off-track jams
• Helps the rack/drawer glide quietly and evenly
• Common signs to replace: hard-to-slide movement, squeaking/grinding, wobble or tilt, or a cracked/missing wheel

• Disconnect power before servicing; shut off water supply if applicable to your appliance
• Remove the rack/drawer to access the roller; support moving parts while working
• Note roller orientation and re-use existing fasteners/clips as designed
• Replace both sides for even operation

The Freezer Tray Roller is an OEM part for LG refrigerators. It is a dual roller wheel assembly located at the rear wall of the freezer compartment. The roller aids sliding shelf movement by reducing friction between trays and the liner wall. 

Causes of a bad freezer tray roller include cracks, flat spots, or separated roller pieces from wear over years of use.

Symptoms of a bad tray roller are:

• Difficulty sliding shelves smoothly in and out of position
• Excessive force required to access stored items
• Noisy operation or rattling noises within the freezer

This genuine LG OEM replacement part is also compatible with some Kenmore models.

The Tray Assy, Drawer is an OEM part for LG refrigerators. This drawer tray provides a dedicated storage compartment in the bottom of the refrigerator. It holds heavier items securely on smooth metal rails, facilitating organization and easy access.

Causes of a bad drawer tray can include cracks or breaks in the plastic over time, wear and tear on the sliding mechanism from frequent use, or damage to the mounting rails that secure the tray in place.

Symptoms of a bad tray include:

• The tray no longer fitting flush or securely within the refrigerator frame
• Excessive movement or rattling of items inside the drawer during opening/closing
• Difficulty extending or retracting the drawer smoothly

This OEM LG part is also compatible with some Kenmore models.

The Tray Assy, Drawer is an OEM part for LG refrigerators. This drawer tray provides a dedicated storage compartment in the bottom of the refrigerator. It holds heavier items securely on smooth metal rails, facilitating organization and easy access.

Causes of a bad drawer tray can include cracks or breaks in the plastic over time, wear and tear on the sliding mechanism from frequent use, or damage to the mounting rails that secure the tray in place.

Symptoms of a bad tray include:

• The tray no longer fitting flush or securely within the refrigerator frame
• Excessive movement or rattling of items inside the drawer during opening/closing
• Difficulty extending or retracting the drawer smoothly

This OEM LG part is also compatible with some Kenmore models.

The Drawer Tray Assembly is an OEM replacement part for LG refrigerators. This is a lower freezer drawer.

Causes of a bad tray assembly can include wear and tear over time, damage from overloading or improper use of the drawer, or issues with its sliding operation mechanism.

Symptoms of a bad tray assembly include:

• The drawer not sliding smoothly or getting stuck
• Difficulty opening or closing the drawer fully
• Noisy operation
• Leaks or ice buildup from a damaged seal

This OEM LG part is also compatible with some Sears/Kenmore model refrigerators.

This is a refrigerator shelf assembly that provides a stable, easy-to-clean surface for storing food and organizing items inside the fresh food compartment. Replacing a damaged or missing shelf restores usable space and proper support.

• Supports food items and containers on a rigid, flat surface
• Helps maintain organized storage and visibility in the compartment
• Replace if the glass is cracked, frame is broken, or shelf sags/doesn't seat properly
• Can also address rattling or instability from a warped or damaged shelf

• Unplug the appliance or disconnect power before servicing
• Remove contents and carefully lift out the old shelf
• Align the new shelf with the side rails and fully seat it in the supports
• Handle glass with care; avoid impact and uneven pressure during installation

This shelf net is a replacement refrigerator shelf organizer that helps keep items secure and prevents small or loose items from shifting during door opening. It restores the original containment function of the shelf area. What it does:

• Provides a flexible barrier to hold bottles, jars and small containers in place on a shelf or door bin
• Replaces torn, stretched or missing shelf netting that allows items to fall or move
• Restores the designed containment and improves everyday access to frequently used items
• Fits in the shelf frame to provide lightweight, visible storage without blocking airflow

• One shelf net

• Remove the existing damaged net and clean the shelf frame area before installing
• Snap or clip the net into the shelf/frame slots; no special tools typically required
• Handle carefully to avoid overstretching; ensure clips or tabs fully engage for secure fit
• Disconnect power only if removing shelves near electrical components or light assemblies

This refrigerator shelf provides a stable, easy-to-clean surface for storing food and containers inside the fresh food compartment. It restores usable storage and helps keep items organized and visible. What it does

• Replaces a cracked, chipped or missing shelf so refrigerated items sit level and secure.
• Restores a smooth, easy-to-clean surface that resists spills and stains.
• Slides into existing shelf supports to maintain adjustable storage layout.
• Helps prevent items from falling through or shifting during normal use.

• Remove food and containers before replacing the shelf.
• Handle glass shelves with care; wear gloves to reduce risk of cuts.
• Align shelf edges with the cabinet rails or supports and slide into place until seated.
• Do not force the shelf; check that supports are intact and properly aligned before loading.

This replacement shelf assembly restores usable storage space and provides a stable surface for food and containers in the refrigerator. It's a direct-fit shelf designed to match the original form and function for easy restoration. What it does:

• Provides a flat, stable shelf surface so food and containers sit level and secure
• Replaces cracked, chipped, or missing shelves that cause items to slide or break
• Restores proper shelving layout to help organize interior storage
• Helps maintain even airflow and access to stored items when positioned correctly

• One shelf assembly

• Remove food and unplug the appliance before beginning any service
• Handle glass or trim sections carefully to avoid chipping or injury
• Slide into the existing shelf supports; no special tools typically required
• Replace shelf clips or supports if damaged before installing the new shelf

The Cover Assembly is an OEM part for LG French door refrigerators equipped with integrated television screens. This cover protects the television when not in use.

Symptoms of a bad cover assembly include: 

• Cracked, clouded, or peeling finish reducing aesthetics
• Poor fit allowing dust entry near television components  
• Binding or getting stuck when opening and closing
• Hinges, pins, or latches weakened through repeated use

Causes of failure can be temperature cycling absorbing and releasing moisture daily, over-extension through careless opening/closing, or general wear from constant daily usage.

Replace yours today with this genuine OEM LG cover assembly to restore your refrigerator's integrated display features. A snug fit around the television combined with a durable surface protects against spills for reliable entertainment access. This replacement part is also compatible with KitchenAid, Samsung, and GE refrigerators featuring television modules.

This is a refrigerator shelf assembly that provides a stable, easy-to-clean surface for storing food and organizing items inside the fresh food compartment. Replacing a damaged or missing shelf restores usable space and proper support.

• Supports food items and containers on a rigid, flat surface
• Helps maintain organized storage and visibility in the compartment
• Replace if the glass is cracked, frame is broken, or shelf sags/doesn't seat properly
• Can also address rattling or instability from a warped or damaged shelf

• Unplug the appliance or disconnect power before servicing
• Remove contents and carefully lift out the old shelf
• Align the new shelf with the side rails and fully seat it in the supports
• Handle glass with care; avoid impact and uneven pressure during installation

This is a refrigerator shelf assembly that provides a stable, easy-to-clean surface for storing food and organizing items inside the fresh food compartment. Replacing a damaged or missing shelf restores usable space and proper support.

• Supports food items and containers on a rigid, flat surface
• Helps maintain organized storage and visibility in the compartment
• Replace if the glass is cracked, frame is broken, or shelf sags/doesn't seat properly
• Can also address rattling or instability from a warped or damaged shelf

• Unplug the appliance or disconnect power before servicing
• Remove contents and carefully lift out the old shelf
• Align the new shelf with the side rails and fully seat it in the supports
• Handle glass with care; avoid impact and uneven pressure during installation

This rail holder secures a door rail to keep the door aligned and stable, restoring smooth opening and closing. It's a direct-fit replacement designed to match the OEM mounting points and restore proper door support. What it does:

• Holds the door rail in place so the door stays aligned and operates smoothly
• Prevents rail movement that can cause rubbing, rattling, or uneven closing
• Restores proper support where a worn or broken holder causes loose or sagging rails
• Helps eliminate noise and misalignment symptoms linked to a failed rail support

• One rail holder

• Disconnect power and follow the appliance manufacturer's service instructions before beginning repair
• Remove surrounding trim or screws as needed to access the rail; keep fasteners for reassembly
• Handle door components carefully to avoid damaging glass or seals; a second pair of hands may help
• Verify part orientation and fit before tightening fasteners;

This rail holder is the replacement mounting bracket that secures a drawer or rail assembly in place, restoring proper alignment and smooth movement. It provides a direct-fit replacement when the original bracket is damaged or worn. What it does:

• Secures the rail or slide assembly to keep drawers/rails aligned and tracking smoothly
• Prevents sagging, excessive play, or rail misalignment that can cause binding
• Restores stable support for components that rely on the rail attachment
• Useful when the original holder is cracked, broken, or missing fasteners

• Disconnect power or unplug the appliance before starting any repair
• Access may require removing trim panels or the drawer/rail assembly—keep track of fasteners
• Use appropriate hand tools; avoid forcing parts to prevent further damage

Restore organized storage with this fresh room tray assembly for your refrigerator. It replaces a cracked or missing deli/fresh drawer so items slide smoothly and stay easy to see and reach.

• Creates the fresh room/deli drawer storage area in the refrigerator compartment
• Slides on the existing rails for smooth access to stored items
• Helps keep items contained and organized
• Replaces a cracked, warped, or missing drawer that won't slide or stay in place

• Remove the old drawer by pulling it out and lifting/tilting as your model's diagram shows; install by aligning with the rails and sliding in until fully seated
• Handle plastic carefully; do not force into place to avoid stress cracks
• No tools typically required; disconnect power only if working near electrical components

This tray cover replaces a damaged or missing appliance tray cover to restore a clean appearance and proper containment of spills. It fits into the existing tray location and helps keep interior surfaces protected during normal use. What it does:

• Covers the appliance tray to help contain spills, crumbs, and minor debris
• Maintains a finished look and helps prevent direct contact with the underlying tray
• Supports proper placement of removable trays or components that sit above it
• Useful when the original cover is cracked, warped, or otherwise compromised

• One replacement tray cover

• Basic snap-in or screw-in installation; confirm orientation before fastening
• Power off and unplug the appliance before attempting any service
• Use gentle pressure to avoid cracking the new cover; do not force damaged fasteners
• Replace missing or damaged screws or clips with OEM-specified hardware

The Deli Drawer Front Cover is an OEM part for LG refrigerators. It provides an attractive facia that protects the internal components of the deli drawer. This cover is designed to integrate with the style and finish of the refrigerator interior. 

Symptoms of a bad Deli Drawer Front Cover include: 

• Cracks, chips, or other visible cosmetic damage
• Discoloration that detracts from the aesthetics  
• The cover is loose, misaligned, or missing
• Difficulty opening or closing the deli drawer

Causes of a bad cover can be normal wear and tear over time from repeated use, as well as accidental drops or impacts that cause cracks or breaks.

This OEM replacement part is also compatible with select LG models.

This decor cover is a small trim piece that snaps over a mounting point to hide screws and finish the look of your appliance. Replacing a cracked or missing cover restores appearance and helps protect the underlying hardware. What it does:

• Conceals exposed fasteners/edges for a clean, finished appearance
• Helps shield underlying mounting points from dust and minor splashes
• Replaces a cracked, warped, discolored, loose, or missing trim cover/cap
• Common signs: exposed screws or gaps, loose adjacent trim/handle, rattling, or a cover that won't stay attached

• 1 decor cover

• Disconnect power to the appliance before starting
• Use a non-marring plastic pry tool to release the old cover to avoid scratching nearby surfaces
• Note the orientation and tab locations; align and snap the new cover into place with even pressure
• Verify a secure fit and reference your model's parts diagram for exact placement

Vegetable Tray Assembly keeps produce organized and supported inside the refrigerator's crisper area. Replace a damaged or warped tray to restore proper storage, prevent produce from sliding, and help maintain interior organization. What it does:

• Supports and contains fruits and vegetables in the refrigerator crisper area.
• Restores a stable surface when the original tray is cracked, chipped, or warped.
• Helps prevent items from sliding or catching while opening and closing the drawer.
• Intended as a direct replacement to return the crisper section to normal use.

• Remove produce and slide the crisper drawer out before replacing the tray.
• Inspect drawer guides and seating points for debris; seat the new tray fully into the guides.
• Handle carefully to avoid damage; wear gloves if surfaces are sharp or dirty.

This lamp cover is the replacement light lens that protects and diffuses the appliance's internal lamp, restoring even illumination and shielding the bulb from moisture and debris. It's a direct-fit exterior lens for the lamp assembly. What it does:

• Protects the interior lamp from dust, moisture and impact to help prevent bulb damage
• Diffuses and directs light for even illumination inside the compartment
• Restores a cracked, yellowed or missing lens to improve visibility
• Helps maintain the lamp assembly's proper fit and alignment

• One lamp cover / light lens

• Power off and unplug the appliance before beginning any service
• Remove lamp bulb per manufacturer instructions before replacing the cover to avoid damage
• Use proper tools and handle the lens gently to avoid scratching or cracking
• If mounting clips or screws are worn or missing, replace them separately

A replacement rail guide assembly that restores smooth, stable sliding for refrigerator/freezer drawers and shelves. Helps reduce sticking and misalignment so drawers open and close more reliably. What it does:

• Guides drawer or shelf movement along the rail for smooth sliding
• Helps keep drawers aligned and prevents binding or tipping
• Reduces noise and catching when opening or closing drawers
• Restores proper support for heavy or loaded drawers

• Disconnect power or unplug appliance before accessing drawers or internal components
• Remove affected drawer or shelf to access mounting points
• Inspect mounting clips and screws; reuse only undamaged hardware or replace as needed
• Test drawer operation after installation to ensure proper alignment and secure fit

This rail guide assembly supports and guides a sliding drawer, bin, or rack along its track for smooth, stable movement. Replacing a worn guide restores easy operation and helps prevent sticking, wobbling, or the slide coming off the track.

• Guides and supports the sliding drawer/bin/rack on its rail
• Maintains alignment so it opens and closes smoothly
• Helps prevent binding, uneven extension, and derailment
• Typical symptoms: hard-to-open drawer, tilt or sag, squeaking/grinding, or visible cracks/warping in the guide

• Disconnect power to the appliance before servicing
• Empty and remove the drawer/bin; disengage from the tracks per your model's procedure
• Remove mounting hardware, transfer any brackets/clips from the old guide, and install the new guide in the same orientation
• Verify smooth travel and proper alignment before reloading

This freezer door foam assembly restores the insulated core inside a freezer door to help the door maintain proper cold retention and reduce frost. It replaces damaged or compressed foam that can compromise the door's thermal barrier. What it does:

• Replaces the insulated foam core inside the freezer door to improve thermal performance
• Helps reduce frost buildup and uneven temperatures caused by degraded door insulation
• Supports a tighter door fit by restoring original door thickness and shape
• Works with the existing door liner and outer panel to re-establish proper sealing

• Disconnect power to the appliance before starting any repairs.
• Removal of the inner door liner or outer panel is commonly required; handle panels and clips carefully to avoid damage.
• Use proper tools and keep small fasteners organized; inspect door gasket and hardware while the door is open.

This freezer door foam assembly restores the insulated core inside a freezer door to help the door maintain proper cold retention and reduce frost. It replaces damaged or compressed foam that can compromise the door's thermal barrier. What it does:

• Replaces the insulated foam core inside the freezer door to improve thermal performance
• Helps reduce frost buildup and uneven temperatures caused by degraded door insulation
• Supports a tighter door fit by restoring original door thickness and shape
• Works with the existing door liner and outer panel to re-establish proper sealing

• Disconnect power to the appliance before starting any repairs.
• Removal of the inner door liner or outer panel is commonly required; handle panels and clips carefully to avoid damage.
• Use proper tools and keep small fasteners organized; inspect door gasket and hardware while the door is open.

The Door Gasket is an OEM part for LG refrigerators. This gasket creates an insulating barrier to keep cool air locked inside.

Causes of a bad door gasket can involve deterioration of rubber over many years of compression and expansion as doors open and close. Mineral deposits may lead to premature cracking as well.

Symptoms of a bad door gasket include:

• Cool air leaks raising energy costs noticeably
• Frost or condensation buildup along door edges
• Inability to maintain proper interior temperatures
• Premature wear of other components from compromised seal

This OEM LG part is also compatible with some Kenmore models.

This left-side door handle trim restores the finished appearance and edge protection on compatible refrigerators. It replaces cracked, scratched or missing trim to help the handle sit flush and improve the door's cosmetic finish. What it does

• Covers and protects the outer edge of the left door handle area
• Replaces cracked, broken or cosmetically damaged trim pieces
• Helps the handle sit flush and maintain a clean, finished look
• Works with the original mounting points and hardware

• One left door handle trim

• Remove contents from the door and support the door before beginning work
• Use basic hand tools to remove existing trim and secure the replacement to existing screw holes
• Do not force or bend the trim; align to original mounting points to avoid damage

This decor handle is the exterior trim piece for a refrigerator door that restores the original look and grip. It replaces cracked, scratched, or worn trim to improve appearance and provide a finished surface where the handle mounts. What it does:

• Replaces damaged or worn decorative handle trim to restore the appliance's appearance
• Covers and protects the handle mounting area from dirt and wear
• Helps provide a consistent grip surface along the door's edge
• Addresses cosmetic issues like scratches, chips, or fading

• Remove any tape or packaging and match the piece to the door before starting
• Support the door or work with a second person if needed to avoid stress on hinges
• Basic hand tools (screwdriver or nut driver) may be required to remove and reinstall mounting hardware
• Follow OEM instructions and disconnect power only if instructed for models with electrified door components

This hinge cover assembly replaces a damaged or missing hinge trim to protect the hinge mechanism and restore the appliance's finished appearance. It snaps into place over the hinge area for a clean, secure fit. What it does

• Covers and protects the hinge mechanism from dirt and debris.
• Restores the appliance's finished appearance when the original cover is cracked or broken.
• Helps prevent accidental contact with moving hinge parts.
• Common symptom: visible broken or missing hinge trim exposing the hinge.

• One hinge cover assembly.

• Disconnect power (and water, if appliance type requires) before starting any repair.
• Remove any outer panels or trim as needed to access the hinge per the appliance service instructions.
• Handle plastic trim pieces carefully to avoid cracking during removal/installation.

This hinge cover assembly replaces a worn or damaged lid hinge cover to restore a smooth, finished look and protect the hinge area from debris and pinching. It helps keep the hinge area sealed and reduces snagging on the lid edge. What it does:

• Covers and protects the lid hinge and pivot area from dirt and moisture
• Restores a clean appearance where a cracked or missing hinge cover was visible
• Helps prevent clothing or hands from catching on the exposed hinge
• Can reduce rubbing noise caused by contact with a damaged cover

• Basic removal of the lid or access panel may be required; follow for proper disassembly
• Use appropriate hand tools and keep small fasteners secure during reassembly
• Disconnect power (and water for washers) before starting work to avoid injury

This name plate is the exterior emblem that mounts to the appliance's front panel. It replaces a missing, cracked, or faded badge to restore a clean, factory look and cover the designated trim area.

• Attaches to the outer panel to display brand/series identification
• Restores a finished appearance where the original emblem sits
• Direct replacement for a lost, damaged, or worn badge
• Typical symptoms: missing emblem, loose or broken tabs, peeling, or discoloration

• Disconnect power before servicing the appliance
• Carefully remove the old emblem; release any tabs from behind or peel away remaining adhesive
• Clean and dry the mounting surface; remove all residue for best fit
• Align with the recess/holes and press evenly until fully seated

The Handle Assembly is an OEM part for LG refrigerator freezer compartments. It includes the handle and mechanical components that operate the freezer drawer.

Causes of a bad handle assembly can include fatigue from repeated opening and closing motions, damage sustained from heavy loads, or exposure to harsh chemicals over years of use.   

Symptoms of a bad handle assembly include:

• Handles detaching from the drawer front  
• Difficulty smoothly opening and closing the freezer drawer
• Inability to fully open or close the drawer
• Excessive play, wobble, or loose motion in the handle

Replace yours today with this genuine OEM LG assembly to restore effortless operation. This replacement handle is compatible with Frigidaire, Samsung, Whirlpool, and some Kenmore models.

This refrigerator door foam assembly replaces the factory insulation inside the door to help restore proper thermal performance and reduce cold spots. It fits behind the door liner to improve internal insulation and control condensation. What it does:

• Replaces damaged or compressed door insulation that can lead to uneven cooling or cold spots
• Helps reduce interior condensation forming on the door surface when installed correctly
• Restores the door's intended thermal barrier to support stable temperatures inside the cabinet
• Helps maintain proper spacing and support for the inner door liner

• One refrigerator door foam assembly (1 count)

• Disconnect power to the appliance before starting any repairs
• Access requires removing the door liner/panels; handle the liner and foam carefully to avoid damage
• Use appropriate tools and follow manufacturer service instructions for reassembly and fastener torque

This is a door assembly that has been manufactured by LG for use with refrigerators. The door assembly includes multiple parts required for replacing the entire door, such as the inner liner and the outer panel. A working door is necessary for the refrigerator to maintain cold enough temperatures inside. If the current door is dented, bent, detached, or otherwise broken, it should be immediately replaced. This replacement might require two people, as the door is heavy. Take proper safety precautions, such as wearing work gloves and disconnecting the appliance from the power source.As a genuine OEM part, this door assembly has been sourced directly from the manufacturer and is only sold individually. This door assembly is manufactured from high-quality and durable materials to ensure durability. It is intended for use with refrigerators manufactured by LG.

The refrigerator door gasket seals the gap between the door and cabinet to keep cold air in and humid air out, helping maintain temperature, reduce frost and condensation, and restore a tight, reliable door close.

• Creates an airtight perimeter seal to prevent warm air leaks
• Helps stabilize interior temperature and humidity
• Minimizes frost buildup and condensation around the door
• Common symptoms: torn or deformed seal, door not sealing, moisture/frost near door, rising temps

What's included: 1 door gasket Installation notes:

• Disconnect power before servicing
• Allow the new gasket to warm to room temperature; soften in warm water or with gentle, low heat to relax folds
• Remove the old gasket and thoroughly clean the mounting channel/mating surfaces
• Seat the new gasket starting at the corners, then along the sides; ensure it's fully engaged and even all around, and check door alignment/seal

Restore a tight, reliable seal on your refrigerator door with this replacement gasket. A fresh gasket stops cold-air leaks that lead to frost, condensation, and temperature swings—helping your fridge run smoothly and keep food at the right temperature. What it does:

• Seals the gap between the door and cabinet to keep cold air in and warm air out
• Helps maintain consistent interior temperature and humidity
• Reduces frost and condensation around the door opening
• Common symptoms: torn or warped gasket, door not closing flush, moisture at the seal, frost buildup, or the unit running more than usual

• 1 door gasket

• Disconnect power before starting and clear items from the door
• Lay the new gasket flat and gently warm it (hot water or low-heat hair dryer) to relax folds
• Starting at the corners, press the gasket lip fully into the door channel and work evenly around
• Perform a paper-slip test around the perimeter and adjust door alignment if needed; avoid overheating the gasket

The Refrigerator Flipper Assembly is an OEM part for LG refrigerators. This assists in the smooth opening and closing of the refrigerator door. It ensures an airtight seal when the door is closed, preventing cool air from escaping and maintaining the refrigerator's internal temperature. 

Causes of a malfunctioning Refrigerator Flipper Assembly can range from physical damage, such as cracks or breakage, to wear and tear from regular use.

Symptoms of a bad Refrigerator Flipper Assembly include:

• Difficulty in opening or closing the refrigerator door
• A noticeable gap when the door is supposed to be sealed shut
• Increased energy consumption as the refrigerator works harder to maintain its temperature
• Spoilage of food items quicker than expected due to poor temperature regulation

This OEM LG part is also compatible with some Kenmore models.

This drawer guide is a replacement rail that supports and guides a refrigerator/freezer drawer for smooth opening and closing. It restores proper drawer alignment and helps prevent sticking or uneven movement. What it does:

• Replaces a worn, bent, or broken drawer guide to re-align the drawer track and improve sliding action
• Helps eliminate drawer sticking, catching, or uneven travel caused by damaged rails or mounting points
• Restores smooth, stable drawer operation under normal load conditions
• Works as part of the drawer slide assembly to keep the drawer seated and centered

• One drawer guide (rail)

• Remove all food and shelves from the drawer before servicing; support the drawer while removing guides
• Use basic hand tools; keep fasteners and mounting clips for reinstallation if present
• Inspect mating tracks, clips and mounting points; replace damaged hardware as needed

This replacement door basket restores usable storage space inside the refrigerator door, keeping bottles and condiments organized and secure. Durable plastic construction provides a stable shelf for everyday items. What it does:

• Replaces a cracked, broken, or missing door bin to restore door storage
• Holds bottles, jars and small containers to prevent shifting during use
• Prevents items from falling out when opening or closing the door
• Restores proper fit and alignment of door shelving where damaged

• Remove food and lower door shelves before installing to avoid damage
• Snaps into existing door track or support tabs; replace carefully to avoid breaking plastic clips
• Use only gentle pressure; do not force or pry with tools
• If clips are damaged, inspect adjacent mounting hardware and replace as needed

The door basket is an OEM part for LG refrigerators. It is the basket located inside the refrigerator or freezer door that provides storage for smaller items like condiments, spreads, or snacks. The basket measures approximately 12" width x 3 1/4" height x 3 1/4" depth. 

Symptoms of a bad basket include:

• The door basket being loose, cracked, or damaged
• Difficulty removing or replacing the basket 
• Reduced storage capacity due to a warped or broken basket

Causes of a bad door basket can be normal wear and tear over time, exposure to excessive weight that stresses the plastic material, or accidental damage from dropping or impact.

This OEM LG part is also compatible with select Sears/Kenmore models.

The Door Bin is an OEM part for LG refrigerators. It provides convenient storage for items accessed regularly, from condiments to snacks.

Causes of a faulty door bin can include plastic cracking from extended usage, broken slide pegs, or a loose assembly. Regular temperature changes may compromise durability over time.

Symptoms of a problematic door bin include:

• Difficulty fully extending or retracting on glide tracks
• Contents are at risk of falling during opening/closing
• Rattling or vibrations while retrieving items

This LG part is also compatible with some Kenmore models.
 

STOPPER ASSEMBLY,DOOR

STOPPER ASSEMBLY,DOOR

This hinge cam fits the door hinge and provides the lift/settle action that helps the door open and close smoothly. Replacing a worn cam can reduce clicking and restore consistent door movement and alignment.

• Provides cam action at the hinge for smooth door travel
• Helps the door seat closed and maintain alignment
• Common symptoms include clicking/knocking at the hinge, rough or uneven door movement, or slight door sag
• Visual wear such as flat spots or grooves on the cam is a typical failure sign

• Disconnect power to the appliance before servicing
• Support the door to prevent injury; remove hinge cover and hardware as needed
• Note the cam's orientation and any washers/spacers and transfer them to the new part
• After installation, verify door operation and gasket alignment; adjust hinge if needed

The Lower Refrigerator Door Hinge is an OEM part for LG refrigerators. This hinge supports the refrigerator door, allowing it to open and close smoothly while maintaining proper alignment. It is designed to handle the weight of the door and ensure a secure and stable operation over time.

Causes of a bad lower refrigerator door hinge can include regular wear and tear, physical damage from overloading or impacts, and gradual loosening over time. A faulty hinge can lead to misalignment, difficulty in opening or closing the door, and potential damage to the door seal.

Symptoms of a bad lower refrigerator door hinge include:

• The door not closing properly or staying open
• Sagging or misaligned door
• Unusual noises when opening or closing the door
• Gaps in the door seal, causing cooling inefficiency

This OEM LG part is also compatible with Sears/Kenmore models.

The Door closer is an OEM part for LG refrigerators, this part prevents the refrigerator door from swinging open too widely. By limiting the door's range of motion, the Door Stop ensures that the door opens smoothly and safely, contributing to the longevity of the appliance and maintaining the aesthetic integrity of your kitchen space.

Causes of a bad Door closer can stem from physical damage, wear and tear over time, or loosening of the component due to repeated use. 

Symptoms of a bad Door closer include:

• The refrigerator door swinging open too far
• Damage or marks on adjacent walls or furniture from the door hitting them
• Increased wear on the refrigerator's hinges due to uncontrolled door movement

This OEM LG part is also compatible with some Kenmore models.

Replace a worn, loose, or broken refrigerator door handle with this complete handle assembly. It restores a secure, comfortable grip so you can open and close the refrigerator door easily while maintaining the unit's original look. What it does:

• Attaches to the refrigerator door to provide a sturdy handhold
• Replaces cracked, broken, or missing handles
• Helps correct a loose or wobbly handle that won't stay secure
• Restores the factory appearance of the door

• 1 refrigerator door handle assembly

• Disconnect power and protect the door surface with tape or a cloth before starting
• Remove any trim/caps as needed and loosen the hidden set screws or mounting bolts on the old handle
• Position the new handle, then tighten fasteners evenly—do not overtighten
• Reinstall any caps/trim and ensure the handle is secure

This slide rail is a replacement drawer guide that restores smooth, stable drawer movement and helps prevent binding or sagging. Designed to match the OEM fit so drawers open and close reliably. What it does:

• Guides and supports the appliance drawer for smooth sliding motion
• Replaces worn or damaged rails that cause sticking, sticking intermittently, or uneven travel
• Helps prevent drawer tilt or sag when loaded
• Restores proper alignment for secure closing

• Disconnect power to the appliance before beginning any work
• Remove the drawer per your model's service instructions to access the rail
• Use basic hand tools (screwdriver/driver) to remove and replace the rail; keep fasteners for reuse
• Align the rail carefully, slide the drawer to test operation, and verify smooth movement before returning the appliance to service

This slide rail supports and guides a drawer, bin, or rack so it can glide smoothly in and out of the appliance. Replacing a worn or broken rail restores alignment and easy operation while preventing binding or derailment. What it does:

• Provides the track surface for a drawer, bin, or rack to slide on
• Keeps the sliding assembly aligned and level during travel
• Worn rails can crack, warp, or lose mounting tabs over time
• Symptoms include sticking, rough travel, derailment, uneven drawer/rack, or difficulty fully opening/closing

• 1 slide rail

• Disconnect power before servicing; shut off the water supply
• Remove the drawer/rack and any end caps or stops per your model's instructions
• Position and secure the new rail using the original fasteners; transfer any reusable stops
• Reinstall and test for smooth, even travel; inspect the companion rail and rollers/wheels for wear

This connector assembly secures and drives the freezer drawer bar so the drawer opens and closes smoothly. Replaces a worn or broken bar/gear assembly to restore proper drawer movement and alignment. What it does:

• Transfers drawer motion to the slide mechanism so the freezer drawer glides correctly
• Replaces worn or stripped gears that cause slipping, grinding, or uneven movement
• Secures the drawer bar to the internal slide/track to prevent misalignment or sagging
• Useful when a drawer won't open/close smoothly, catches, or rattles during operation

• Disconnect power before servicing and remove stored items from the drawer
• Generally replaces with basic hand tools; support the drawer while detaching and installing the assembly
• Inspect surrounding slide components for wear and replace if needed for reliable operation

This center hinge assembly secures and allows smooth pivoting of the refrigerator's center door, restoring proper door alignment and closing. It replaces a worn or damaged hinge to reduce sagging and improve sealing. What it does:

• Provides the pivot point for the refrigerator's center door, maintaining correct door movement and alignment
• Helps the door close evenly to preserve the gasket seal and internal temperature
• Replaces broken, bent, or worn hinge hardware that can cause door sag or rubbing
• Works with existing hinge pins and mounting points to restore original function

• One center hinge assembly

• Requires basic hand tools; follow manufacturer instructions for removal and installation
• Support the door while removing or installing the hinge to prevent injury or damage
• Ensure all fasteners are tightened securely and door alignment is checked after installation
• Disconnect power if required by the appliance manufacturer before servicing

This center hinge assembly secures and pivots the upper/center refrigerator door, restoring proper door alignment and smooth opening. Designed to replace a worn, bent or broken center hinge to improve sealing and operation. What it does:

• Provides a mounting pivot for the upper/center refrigerator door to ensure correct swing and alignment
• Helps maintain an even door gap for a proper seal and consistent cooling
• Replaces damaged, bent or worn hinge components that cause rubbing, sagging, or noisy door movement
• Works with factory hinge pins and covers to restore original door function

• One center hinge assembly

• Installation requires removing the door and supporting it; have a helper to prevent damage or injury
• Use appropriate hand tools; avoid overtightening fasteners which can bind the hinge
• Inspect adjoining hinge pins and mounting screws; replace if worn for best results
• Disconnect power or follow manufacturer safety steps if working near electrical components

The Spanner Wrench is an OEM replacement part for LG refrigerators. This tool allows you to adjust the door hinges to ensure the doors are level and aligned properly. A well-aligned door is crucial for maintaining the internal temperature and efficiency of the refrigerator, preventing energy loss and ensuring food is stored under optimal conditions.

Symptoms that you might need to adjust the door hinges and potentially need this wrench include:

• Doors not closing properly or sealing tightly
• Visible gaps between the door and the main body of the refrigerator
• The refrigerator tilting or not sitting level

This spanner wrench is also compatible with some Sears/Kenmore refrigerators. 

This upper hinge assembly secures and guides the refrigerator door at the top, restoring proper alignment and smooth opening. Replace a worn hinge to stop sagging doors and improve sealing and operation. What it does:

• Provides the top pivot point for the refrigerator door, keeping it aligned during opening and closing
• Restores proper door clearance and prevents rubbing or misalignment
• Helps maintain a tight door seal to reduce cold air loss
• Addresses symptoms like a sagging or uneven door, noisy movement, or difficulty closing

• Disconnect power to the appliance before beginning repairs to prevent injury.
• Support the door while removing and installing the hinge to avoid dropping or damage.
• Use appropriate hand tools; do not overtighten fasteners to prevent stripping.

Replacement refrigerator door hinge that restores smooth pivoting and proper door alignment, helping the door open and close reliably and maintain an airtight seal to preserve cooling performance. What it does:

• Supports the refrigerator door and allows it to pivot smoothly.
• Replaces worn, bent, or damaged hinges that cause door sag or misalignment.
• Helps reduce noisy or grinding door operation when the hinge is failing.
• Promotes an even door seal to help maintain internal temperature consistency.

• Unplug the appliance and remove food from nearby shelves before starting work.
• Support the door while removing hinge fasteners to prevent dropping or damage.
• Reinstall using the original hardware; align the door and tighten fasteners securely but avoid overtightening.

This duct cap assembly seals and finishes the dryer exhaust opening, directing airflow out of the appliance while protecting the duct connection from damage. It restores a secure exhaust path and helps maintain proper venting performance. What it does:

• Covers and secures the dryer exhaust/duct outlet to provide a stable connection point for the vent hose.
• Helps prevent air leaks at the duct connection that can reduce drying efficiency.
• Replaces cracked, broken, or missing outlet caps that cause rattling or poor airflow.
• Supports proper exhaust routing to reduce lint buildup at the connection point.

• One duct cap assembly.

• Disconnect the appliance from power (and gas if applicable) before accessing the duct area.
• Move the appliance away from the wall to reach the rear exhaust; remove the old cap and any sealing tape or clamps.
• Reattach the duct hose and secure with the original clamp or a replacement clamp rated for dryer vents.
• After installation, run a short cycle to verify a tight fit and proper exhaust flow; inspect for leaks or unusual vibration.

This lever return spring restores proper tension to the lever assembly so the control or latch returns smoothly. A direct-fit replacement designed to restore normal lever movement and function. What it does:

• Provides return tension for the lever to ensure reliable latch or control movement
• Helps stop the lever from sticking or remaining engaged after use
• Restores smooth, consistent operation when the original spring is worn or broken
• Commonly replaced when lever movement feels loose or fails to return

• One spring lever

• Disconnect power (or unplug) and follow appliance safety procedures before servicing
• Access may require removing panels or the control/door assembly; keep fasteners organized
• Inspect mating lever and pins for wear; replace damaged components to prevent repeat failure

The Link is an OEM part for LG refrigerators. It serves as an integral connector between the refrigerator door and cabinet, facilitating smooth opening and closing of the door. With durable construction and precise engineering, the link is designed to withstand the rigorous motion of hundreds of door openings without compromising functionality. 

Symptoms of a bad link include:

• Doors that do not close or seal properly 
• Excessive noise or vibration from the door area
• Damage, bending, or breakage of the connecting pieces
• Misalignment impairing proper door operation

Causes can stem from normal wear and tear over many years of use. Replacing a faulty link restores the refrigerator door's designed motion for convenient access to the interior.

This OEM LG part fits seamlessly while extending the product's useful life. This part is also compatible with Kenmore models featuring LG's refrigerator link assembly design.

This lever button is the push-style control used to activate a specific function on the appliance's control panel. It restores tactile control and makes it easy to trigger the associated feature without replacing the whole panel. What it does:

• Acts as the user-facing push lever that completes the button action on the control assembly
• Replaces a cracked, worn or unresponsive lever that won't depress or return properly
• Helps resolve intermittent or failed button activation when the switch and contacts are otherwise good
• Matches the OEM shape so the button aligns and engages cleanly with the underlying switch

• High-level swap: remove the front/control bezel to access and replace the lever; keep screws and clips organized
• Power safety: disconnect power (unplug or shut off breaker) before servicing control area
• Inspect underlying switch and mounting clips during replacement; do not force parts into place

A small retaining pin used to secure moving parts and keep components aligned for smooth operation. Replacing a worn or broken common pin can stop rattling and restore proper fit between linked parts. What it does:

• Holds or aligns two parts together so they move correctly and stay in position
• Helps prevent rattling, looseness, or parts slipping out of place
• Works as a simple mechanical fastener—no electronics involved

• One common pin

• Disconnect power to the appliance before beginning any service
• Keep track of small parts; lay out components in order to aid reassembly
• May require removal of trim or a hinge/retainer to access the pin—use basic hand tools
• If the pin is difficult to seat, do not force; inspect mating parts for damage

This cabinet roller supports the refrigerator and lets the unit roll in and out of place for cleaning or service. Replace a worn or broken roller to restore smooth movement and help keep the appliance properly positioned.

• Supports the base of the refrigerator and enables rolling movement
• Helps with safe positioning and service access without dragging
• Common failure signs: appliance is hard to move, scraping or rolling noises, a flat-spotted/cracked wheel, or a wheel that won't turn
• Replace when the roller is damaged, seized, or missing

• Disconnect power and shut off water supply; protect flooring before moving the appliance
• With help, pull the refrigerator forward and safely support it to access the roller
• Remove mounting fasteners, install the new roller, and reuse original hardware
• Confirm level and smooth movement before returning the unit to its location

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

This compressor damper is a vibration-isolating mount that sits between the sealed-system compressor and the chassis. It cushions the compressor to reduce noise, limit vibration transfer, and help keep refrigerant lines from being stressed.

• Isolates the compressor from the frame to absorb start/stop shock and vibration
• Helps reduce humming, rattling, or buzzing from the back/bottom of the appliance
• Replaces a damper that's cracked, flattened, hardened, or missing
• Can help if the compressor rocks or the unit vibrates excessively

• Disconnect power and pull the unit forward for access; remove rear/service panel if present
• Support the compressor to relieve load on the mounts before removing fasteners
• Match orientation; transfer any sleeves/spacers from the old damper to the new one
• Ensure the compressor sits level and that tubing is not strained before restoring power

Replacement front cover that restores your appliance's exterior finish and helps protect controls and internal components from everyday wear, spills, and minor impacts, delivering a clean, finished look and proper front-panel fit. What it does:

• Covers and protects the appliance's front area, helping shield controls and wiring from dirt and moisture.
• Restores damaged or cracked front trim for improved appearance.
• Helps maintain proper alignment and fit of the front assembly.
• Common symptom: cracked, chipped, warped, or loose front panel that exposes internal parts or looks worn.

• Disconnect power (unplug or switch off breaker) before starting any repair.
• Basic hand tools (screwdriver set) may be required to remove the old cover and install the replacement.
• Handle edges carefully to avoid cuts; align tabs/clips and secure fasteners snugly but do not overtighten.

This small stopper installs in the refrigerator to limit the travel of a moving component and keep it securely in place. Replacing a broken or missing stopper prevents over-extension and helps maintain smooth, aligned operation.

• Limits the range of motion for a door, bin, or drawer to prevent over-opening or accidental removal
• Helps keep interior components aligned and operating smoothly
• Replace if cracked, missing, or deformed
• Common symptoms: drawer or bin slides out too far, door swings past normal range, or a broken plastic stop is found

• Disconnect power before servicing; remove or support the affected bin/drawer/door
• Note the old stopper's orientation and location before removal
• Transfer and reuse any original screws or clips if applicable
• Snap or fasten the new stopper in place and test for smooth movement

This restrainer is a small retaining clip that helps secure moving or removable components in place, reducing rattles and keeping parts aligned for reliable operation. It's a simple replacement for worn or broken clips. What it does:

• Holds a cover, panel, or door-related component in proper position to prevent shifting
• Reduces noise caused by loose or vibrating parts
• Restores original fit where a broken or missing clip allows movement
• Simple mechanical function — no electrical connections or calibration

• One restrainer

• Disconnect power (and water if applicable) before beginning repairs
• Inspect surrounding mounting points for damage; replace any broken tabs or fasteners
• Typically installs with basic hand tools; align clip and press or snap into place until secure

The Drier Assembly is an OEM part for LG refrigerators. This part removes moisture and contaminants from the refrigerant, ensuring the system operates efficiently and effectively. The drier assembly helps maintain the proper function of the compressor and other cooling components, contributing to the longevity and performance of the refrigerator.

Causes of a bad drier assembly can include clogs from debris, wear and tear over time, or contamination from moisture or refrigerant leaks.  

Symptoms of a bad drier assembly include:

• The refrigerator not cooling properly
• Frost or ice buildup on the evaporator coils
• Increased noise from the compressor
• Reduced efficiency and higher energy consumption
• You should replace the drier assembly if it becomes faulty or damaged.

This OEM LG part is also compatible with select Sears/Kenmore models.

This holder is a small mounting bracket used to secure internal components in place, helping keep parts aligned and stable for reliable operation. It provides a direct, OEM-compatible replacement to restore proper fit and function. What it does

• Secures and supports nearby components to prevent shifting or vibration.
• Restores proper alignment where a worn or broken holder causes rattling or loose parts.
• Helps maintain normal operation by keeping assemblies seated correctly.
• Works behind panels or inside assemblies where a dedicated bracket is required.

• One holder/mounting bracket as shown.

• Installation generally requires removing the panel or access cover where the holder is located.
• Use proper fasteners shown in your appliance; replace any damaged screws or clips as needed.
• Disconnect power before servicing electrical appliances to reduce shock risk.

This condenser assembly with attached wiring replaces a failed condenser section and restores proper refrigerant heat exchange and electrical connection for the condenser circuit. It helps the appliance cool efficiently and run reliably. What it does

• Replaces the condenser coil assembly and integrated wire connections used in the cooling system
• Restores proper refrigerant heat-exchange and airflow through the condenser
• Fixes symptoms like poor cooling, warm compartments, or condenser fan/electrical connection issues
• Matches OEM fit and mounting points for a direct replacement when listed for your model

• One condenser assembly with attached wiring as shown

• Install only if this part matches your model and the failed condenser is confirmed; refer to model-specific service literature
• Unplug power and disconnect the appliance from power source before beginning repair
• Test cooling performance and electrical connections after installation

The Evaporator Fan Blade is an OEM replacement part for LG refrigerators. It is a key component located inside the refrigerator that works to circulate cold air evenly throughout. The fan blade spins rapidly to distribute chilled air from the evaporator coil and refrigeration system, ensuring proper airflow and consistent temperatures across all shelves and compartments.  

Symptoms of a bad evaporator fan blade include:

• Inconsistent or improper interior cooling temperatures 
• Hot or warm spots developing inside the refrigerator
• Strange noises such as clicking or grinding emanating from the rear wall

Causes of a bad evaporator fan blade can be wear and tear over time, an accumulation of dust or debris on the blades restricting airflow, or accidental damage like dents or cracks to the blades affecting their ability to spin smoothly.

This OEM LG part is also compatible with select Sears/Kenmore brand models.

The Condenser Fan Blade is an OEM replacement part for LG refrigerators. The condenser fan motor blade is located on the condenser fan motor which is usually located on or near the compressor at the back of the refrigerator. This part is responsible for circulating air over the condenser coils. This helps to remove heat from the condenser and evaporate water in the defrost drain pan.

Causes of blade failure can include normal wear over extended runtime, accumulated dirt and dust impeding airflow, or physical impact damage.

Symptoms of a faulty condenser fan blade include:

• Refrigerator fails to properly cool and maintain temperatures
• Condenser unit runs excessively as heat fails to dispel
• Abnormal noises such as grinding or squealing emanate from the condenser area

This OEM LG part is also compatible with some Sears/Kenmore model refrigerators.

This fan grille assembly covers and protects the appliance fan while helping direct airflow and minimize noise. It's a direct-fit replacement component that restores proper ventilation and keeps debris away from the fan blades. What it does:

• Shields fan blades from objects and debris that can cause damage or binding
• Directs airflow for more consistent ventilation and cooling performance
• Helps reduce rattle or vibration caused by cracked or loose grille pieces
• Restores proper fan clearance when the original grille is warped or broken

• Disconnect power to the appliance before starting any work.
• Handle the grille carefully to avoid damaging mounting tabs; small plastic clips are common.
• Installation typically requires basic hand tools (screwdriver); align tabs and secure fasteners snugly.

The Dispenser Micro Switch is an OEM part for LG refrigerators. It is a component of the ice and water dispensing system, responsible for activating the dispenser when the lever is pressed. 

Causes of a bad Dispenser Micro Switch can include mechanical wear from frequent use, failure due to moisture or debris affecting the switch’s contacts, or electrical faults that prevent proper signaling.

Symptoms of a bad Dispenser Micro Switch include:

• The dispenser not releasing ice or water when the lever is pressed.
• Continuous dispensing or dripping after the lever is released.
• Intermittent or no response from the dispenser controls.

This OEM LG part is also compatible with Sears/Kenmore.

The Evaporator Fan Motor Assembly is an OEM replacement part for LG refrigerators. This assembly is responsible for circulating cold air from the evaporator coils throughout the refrigerator and freezer compartments. By doing so, it ensures that both compartments maintain the desired temperatures and that the cooling process is efficient.

Causes for a malfunctioning Evaporator Fan Motor Assembly can include motor wear from continuous operation, electrical issues like faulty wiring, obstructions preventing the fan blades from turning, or damage to the fan blades themselves.

Symptoms of a bad Evaporator Fan Motor Assembly include:

• Inconsistent temperatures in the refrigerator or freezer compartments
• Unusual noises, such as humming or buzzing, coming from the back of the refrigerator
• Reduced cooling efficiency, leading to food spoiling faster
• Frost buildup in the freezer due to poor air circulation

This OEM LG part is also compatible with Sears/Kenmore model refrigerators.

Damper motor support secures the damper motor assembly inside the refrigerator, keeping the air-control damper aligned so it opens and closes correctly. Replacing a damaged support restores proper airflow control and reduces noise. What it does:

• Secures and positions the damper motor assembly so the air-control damper moves smoothly.
• Keeps the motor and damper aligned to help prevent rattling, grinding, or loose motor noise.
• Supports consistent airflow between compartments to assist with even cooling.
• Resolve damper movement problems like the damper not opening or closing fully.

• Disconnect power to the appliance before starting work; remove food and shelves as needed for access.
• Remove the interior access panel to reach the damper assembly; handle plastic tabs and clips gently to avoid breakage.
• Align the motor and damper during reassembly and secure all fasteners; test damper operation before replacing panels and shelving.

This damper motor support replaces a broken or warped mount for the refrigerator's air damper assembly. It holds the damper motor and door securely so the system can meter freezer air into the fresh food compartment.

• Secures and aligns the air damper motor/door within the duct
• Helps ensure proper opening/closing of the damper to regulate airflow and temperature
• Damage can contribute to a warm or too-cold refrigerator and inconsistent temperatures
• May cause clicking or buzzing from the damper area or a visibly loose assembly

• Disconnect power to the refrigerator before servicing
• Access the damper behind the fresh food compartment duct/cover; remove shelves as needed
• Note wiring and orientation; transfer the existing damper motor and door to the new support and reuse fasteners
• Ensure the door moves freely and seals before reassembly; restore power and verify airflow

The Ice Dispenser Door Motor is an OEM part for LG refrigerators. This motor is responsible for the operation of the ice dispenser door, controlling its opening and closing mechanism to allow ice to be dispensed without letting warm air into the freezer. 

Symptoms of a bad Ice Dispenser Door Motor include:

• The dispenser door not opening or closing properly,
• Ice not being dispensed when activated,
• Unusual noises coming from the dispenser mechanism.

Causes of ice dispenser door motor failure can include electrical issues such as shorts or wiring problems, mechanical wear over time, or blockages that strain the motor.

This OEM LG part is also compatible with Sears/Kenmore.

The Bracket Assembly is an OEM part for LG French door refrigerators housing circulation fan motors. This mounting bracket securely attaches the integral evaporator motor within the unit compartment. 

Causes of a bad bracket assembly can include loosened fasteners failing to firmly support vibrations over time, impact dents flexing the steel support reducing balance, or corrosion where steel meets refrigerant lines deteriorating contact points.

Symptoms of a bad bracket assembly include:

• Abnormal noises or grinding sounds from motor  
• Reduced airflow from the inlet to outlets inside the fridge
• Loose parts susceptible to movement damage 
• Misalignment reducing the lifespan of bearings

Replace yours today with this genuine OEM LG bracket to restore optimized cooling performance. Rigid clamping securely isolates motor oscillations. Compatible with Samsung, Kenmore, and GE French door models, this replacement sustains proper fit and function. 

This sheath-style heater melts frost from the evaporator during automatic defrost cycles to keep airflow clear and temperatures stable. Replacing a failed heater helps stop recurring ice buildup and restore consistent cooling performance.

• Heats the evaporator to melt accumulated frost/ice during defrost
• Keeps air passages clear to maintain proper temperatures
• Helps prevent frost-packed evaporator covers and reduced cooling
• Common symptoms: heavy frost behind the freezer panel, fan noise from ice contact, weak cooling, long run times

• Disconnect power before servicing; allow any sharp edges to be avoided with cut-resistant gloves
• Access is typically behind the freezer's rear interior panel; remove shelves/drawers and panel to reach the evaporator
• Transfer any clips/sensors attached to the heater in the same positions; avoid bending fins or puncturing refrigerant lines
• Ensure connectors are fully seated and the heater is secured before restoring power and monitoring operation

This LED assembly is a backlight strip used to illuminate the display for clear, even picture brightness. Replacing a faulty strip restores proper screen illumination and can eliminate dark spots or missing segments. What it does:

• Provides the LED illumination source behind the LCD panel for even brightness
• Restores lost or uneven backlighting caused by failed LEDs or damaged strips
• Commonly replaces parts that cause dimming, flickering, or no light on power-up
• Connects to the display's LED driver board to receive power and signals

• Disconnect power and remove the display panel before replacing
• Handle the strip and connector carefully to avoid bending or damaging LEDs and flex cables
• Observe ESD precautions and avoid touching LED surfaces or circuit traces
• Reassemble panels and test before finalizing to ensure proper alignment and function

The Capacitor is an OEM replacement part for  LG refrigerators. It is an electronic component located next to the refrigerator compressor that stores electric charge between cycles of the power supply circuit. The capacitor plays an important role in providing stable starting power to the compressor motor.

Causes of a bad capacitor next to the compressor can include heat distress over thousands of start/stop cycles of the refrigerator.

Symptoms of a bad capacitor include:

• The compressor makes loud buzzing or grinding noises during the operation
• The compressor fails to start or cycles on and off frequently
• Temperature fluctuations inside the refrigerator
• Error codes related to compressor issues

This genuine LG replacement is compatible also with Kenmore Elite model refrigerators

The Compressor Run Capacitor is an OEM part for LG refrigerators. It plays a critical role in the operation of the refrigerator's compressor by providing the necessary electrical boost to start and maintain the compressor's operation.

Causes of a bad compressor run capacitor can include electrical surges, overheating, or simply wear and tear over time. When the capacitor fails, it can no longer deliver the required electrical charge, which impacts the compressor's ability to start and run efficiently.

Symptoms of a bad compressor run capacitor include:

• The refrigerator not cooling properly
• The compressor not starting or running intermittently
• Unusual humming or clicking noises from the compressor area
• The refrigerator cycling on and off frequently

This OEM LG part is also compatible with Sears/Kenmore models.

This DC motor assembly powers a fan inside your appliance to move air where it's needed. Replacing a weak or failed motor restores proper airflow for stable temperatures and reliable performance. What it does:

• Drives a fan blade to circulate air within the appliance
• Supports consistent temperatures and efficient airflow
• Common failure signs: fan not running, intermittent operation, or grinding/squealing noises
• Contribute to poor cooling/heating and fan/motor-related error codes

• Includes: 1 DC motor assembly

• Disconnect power to the appliance before servicing
• Access the fan area, note wire routing/orientation, and remove mounting fasteners
• Transfer the fan blade and any mounting hardware from the original motor if needed
• Ensure the blade spins freely and connectors are fully seated before reassembly and power-up

A replacement display cover assembly for the control panel that protects the display and control buttons while keeping the panel looking clean. Restores the finished appearance and helps shields controls from household wear. What it does:

• Protects the control board display lens and button area from scratches, spills, and everyday wear
• Preserves visibility of the control panel and display indicators
• Helps prevent direct contact with electronics behind the panel
• Useful when the original cover is cracked, scratched, or discolored

• Disconnect power before beginning any repair to avoid shock or damage
• Typically installs at the front control panel; some disassembly of the console may be required
• Handle gently to avoid scratching the new cover during installation

The Icemaker Assembly is an OEM part for LG refrigerators. This assembly is responsible for producing ice and dispensing it into the ice bucket within the freezer compartment. It includes the ice mold, motor, and other components that work together to form, freeze, and release ice cubes efficiently.

You should replace this icemaker assembly if it becomes defective. Common causes of a bad icemaker assembly include wear and tear over time, electrical failures, or blockages in the water supply line. Mineral buildup or malfunctioning components can also hinder the ice-making process.

Symptoms of a bad icemaker assembly include:

• No ice production
• Smaller than usual or misshapen ice cubes
• Leaks or water pooling in the freezer
• Unusual noises coming from the icemaker area

This OEM LG part is also compatible with Sears/Kenmore.

This indoor fan motor powers the air conditioner's indoor unit blower to move air across the evaporator coil. Replacing a weak or failed motor restores proper airflow for effective cooling and comfort.

• Drives the indoor blower/crossflow fan to circulate conditioned air
• Maintains correct airflow across the evaporator for cooling and dehumidification
• Common symptoms of failure: no or weak airflow, fan won't start or stalls, intermittent operation
• May cause unusual buzzing/grinding noises or the unit shutting down with a fan-related fault

• Disconnect power at the breaker before servicing; allow moving parts to stop
• Remove the indoor unit cover and access panel; note wire harness connections and routing
• Transfer any brackets, insulators, or hardware from the old motor if required
• Ensure the fan wheel spins freely and does not rub before restoring power and testing

This sensor PCB assembly detects and relays sensor signals to the appliance control system, restoring accurate sensor feedback and communication when the original sensor board fails or malfunctions. Designed as a direct replacement board. What it does:

• Reads sensor inputs and converts them to signals the main control board can interpret.
• Replaces a failed or intermittent sensor board that causes incorrect readings or sensor-related error codes.
• Can resolve symptoms such as unexpected sensor faults, control errors, or appliances not responding to sensor changes.
• Matches the OEM board function; verify model compatibility before ordering.

• Always disconnect power before servicing to avoid shock or shorting the board.
• Use ESD precautions and handle the PCB by its edges to prevent static damage.
• Ensure all connectors are fully seated and the board is mounted in the original orientation.

This sub PCB assembly is an electronic control board that processes inputs and switches components, coordinating specific appliance functions. Replacing a failed board can restore normal operation and resolve dead controls, error codes, or intermittent, unpredictable behavior. What it does:

• Distributes and regulates control power and switches loads via onboard relays/triacs
• Interprets signals from sensors and the user interface to execute commands
• Coordinates timing and operation of related components per the appliance's program logic
• Failure may present as no power, won't start, unresponsive or flickering display, random beeps, or recurring error codes

• 1 sub PCB assembly

• Disconnect power to the appliance before servicing; verify no voltage is present
• Use ESD protection and handle the board by the edges
• Photograph wiring; transfer connectors one at a time and ensure they are fully seated
• Secure the board with existing fasteners/standoffs; perform any required reset or diagnostic per your model's service info

The Temperature Sensor is an OEM part for LG refrigerators. Also known as a thermistor, is responsible for sensing the temperature changes and providing the necessary feedback to the refrigerator's control board. It helps maintain accurate and consistent temperature levels, ensuring optimal food preservation and efficient cooling.

Causes of a faulty temperature sensor can include wear and tear over time, damage due to electrical issues or exposure to extreme temperatures, or sensor calibration issues. These factors can result in temperature inconsistencies, inaccurate readings, or improper cooling performance of the refrigerator.

Symptoms of a bad temperature sensor may include:

• Incorrect temperature readings on the control panel
• Temperature fluctuations inside the refrigerator
• Overcooling or inadequate cooling of food items

This OEM LG part can also be used on Kenmore/Sears appliances. 

This ice bucket assembly is the removable storage bin that collects and holds cubed ice from the refrigerator ice maker, restoring clean, contained ice storage and proper pickup by the dispenser or scoop. What it does:

• Collects and stores cubed ice produced by the ice maker so ice is contained and ready for use
• Guides ice toward the dispenser/auger area for consistent pickup
• Common symptoms it addresses: cracked or warped bin, ice spilling or falling out, ice not accumulating in the bin
• Fits into the freezer ice maker area and works with the factory guides and ejector mechanism

• Disconnect power to the refrigerator before servicing to avoid injury or damage
• Remove existing bucket by sliding it out of the guides; handle plastic parts gently to avoid cracking
• Reinstall by seating the bucket into the guides until it clicks or seats securely; ice maker components align before restoring power
• After installation, cycle power or run a test ice-making cycle to ensure proper operation

The Ice Maker Assembly is an OEM component specifically designed for LG refrigerators. It is responsible for automatically producing batches of ice cubes on demand. 

Causes of a bad ice maker assembly can include failures in the ejector mechanism that dispenses ice, damage or leaks in the water supply components, or issues with the control board that manages the timing of each cycle. 

Symptoms of a bad ice maker assembly include:

• Failure to produce ice cubes
• Incomplete or misshapen ice cubes  
• Excessive noise during operation
• Water leaks from the ice maker area

This OEM LG replacement part is also compatible with Sears/Kenmore models. 

The Water Tank Assembly is an OEM part for LG refrigerators. It stores and supplies water for the refrigerator's dispenser and ice maker, ensuring a steady and clean water flow for these features.

Causes of a bad water tank assembly can include mineral buildup from hard water, leaks due to cracks or punctures, or contamination from mold or bacteria if the tank is not regularly cleaned. Over time, wear and tear from repeated use can also lead to failure.

Symptoms of a bad water tank assembly include:

• Water dispenser not functioning properly
• Reduced or no ice production
• Leaks or puddles inside the refrigerator
• Unpleasant taste or odor in the water

This OEM LG part is also compatible with Sears/Kenmore refrigerators.

An in-line union for appliance tubing, this tube connector joins two sections of plastic line to create a secure, leak-resistant connection in the water circuit, ideal for restoring flow after a repair, trim, or reroute. What it does:

• Connects two lengths of compatible plastic tubing to form a continuous run
• Helps maintain proper water delivery through the appliance's water system
• Can address leaks, drips, or loose/failed connections at a splice point
• Useful when replacing, shortening, or rerouting tubing during service

• 1 tube connector

• Disconnect power and shut off the water supply before servicing
• Cut tubing square; ensure ends are clean, round, and free of gouges
• Insert tubing fully into the connector until seated, then perform a gentle pull test
• Restore water and inspect all joints for leaks; use the connector size that matches your tubing's outer diameter

This tube assembly directs water through the appliance, restoring a secure, leak-resistant path when the original line is brittle, kinked, or damaged. Replacing it helps stop leaks and restores normal water flow.

• Routes water from the inlet valve to internal components
• Maintains sealed connections to reduce drips and seepage
• Replaces tubing that is cracked, kinked, or clogged with mineral deposits
• Common symptoms: visible leaks, puddling, low flow, or intermittent water delivery

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water and relieve line pressure
• Note the routing and connection points; transfer any retainers from the old part if needed
• Insert tubing fully into fittings and tug gently to confirm engagement; restore water and check for leaks

The Water Inlet Valve is an OEM part for LG refrigerators. It controls the flow of water into the refrigerator for the ice maker and water dispenser, ensuring a steady and controlled supply of water.

You should replace the water inlet valve if it becomes clogged, damaged, or fails to function properly. Causes of a bad water inlet valve can include mineral buildup from hard water, electrical malfunctions, or general wear and tear over time.

Symptoms of a bad water inlet valve include:

• The ice maker not producing ice
• The water dispenser not dispensing water
• Leaking water from the valve area
• Unusual noises when the valve is operating

This OEM LG part is also compatible with Sears/Kenmore refrigerators.

The Water Valve Assembly is an OEM part for LG refrigerators. It is essential for controlling the flow of water to the ice maker and the water dispenser. This solenoid-operated valve responds to signals from the refrigerator’s electronic control system to accurately manage the release of water, ensuring efficient operation and reliability.

Symptoms of a bad Water Valve Assembly include:

• The ice maker not producing ice or producing very small cubes
• The water dispenser not functioning or dispensing a trickle instead of a steady flow
• Water leaking from the refrigerator

Causes of a bad water valve assembly can stem from mineral deposits that clog the valve, electrical failures that impair the valve’s operation, or wear and tear from normal usage leading to leaks or malfunctions.

This OEM LG part is also compatible with Sears/Kenmore.

Note: Flow meter is not needed on all models, remove if necessary. Redesigned single valve replaces older dual solenoid valves. Wiring harness is included. Located behind the refrigerator.

This replacement cover filter secures and protects the unit's internal air filters while maintaining correct airflow. It restores the sealed fit of the filter compartment to help the appliance run as intended. What it does:

• Holds the internal filter in place so air passes through the filter media
• Prevents large debris and foreign objects from reaching internal components
• Helps maintain designed airflow path for consistent performance
• Can reduce rattling or vibration caused by a loose or damaged cover

• Unplug the appliance or disconnect power before starting
• Remove the front panel or filter access per the owner's manual to reach the cover
• Align tabs and snap or fasten the cover securely; do not force parts
• Do not operate the appliance with missing or damaged filter cover

This water filter assembly replaces the refrigerator's water filtration module to help restore clear-tasting water and steady flow. Fits models that use the AGF80300705 assembly and installs at the refrigerator water inlet. What it does:

• Filters sediment and common taste/odor contaminants to improve drinking water quality
• Restores reduced water flow caused by a clogged or failing filter module
• Helps reduce visible particulates and cloudiness in dispensed water
• Prevents unfiltered water from reaching the dispenser/ice maker when installed

• Turn off refrigerator water supply before replacing the assembly to avoid leaks
• Hand-tighten connections; avoid overtightening fittings to prevent damage
• Run and discard the manufacturer-recommended initial volume of water after install to flush the system

The Filter Head Assembly is an OEM replacement part for LG French door refrigerators. The component that houses the built-in water filter responsible for cleaning water delivered through the refrigerator’s internal dispenser and ice maker. With its precise fit, the filter head assembly ensures the water filter is securely held in place to do its job properly.

Symptoms of a bad filter head assembly include:  

• Water dispensing or ice making issues
• Water leaks around the filter area  
• Error messages related to filter replacement
• Inability to change or install a new filter

Causes of failure can be cracks, cracks, mineral buildup, or normal wear over time. Filter head assemblies in continuous use may need periodic replacement.

This OEM part is also compatible with some Kenmore side-by-side refrigerators.

This genuine replacement filter cover secures and protects the unit's air filter, helping keep the filtration system sealed and operating as designed. Restores proper fit and helps maintain airflow through the filter assembly. What it does:

• Holds the air filter in place and protects the filter media from debris
• Helps maintain correct airflow through the filter chamber for effective filtration
• Prevents gaps that can allow unfiltered air to bypass the filter
• Restores a secure fit if the original cover is cracked, warped, or missing

• One filter cover

• Disconnect power to the appliance before removing or replacing the cover
• Remove the old cover by releasing any clips or tabs, then snap or slide the new cover into place
• Inspect surrounding seal/gasket and filter media for damage while installing
• If clips or tabs are damaged, replace them before operating the appliance

This complete freezer door assembly replaces a damaged or worn freezer door to restore proper closure and cold retention. It fits the freezer compartment and includes the door shell and attached inner components for a like-for-like replacement. What it does:

• Replaces a cracked, dented, or warped freezer door to help prevent cold air loss
• Restores proper door alignment and sealing to reduce frost buildup and temperature issues
• Provides the original mounting points and inner components for easy fitment
• Helps the freezer maintain consistent performance when the old door can't close or seal properly

• Disconnect power to the appliance before starting any repair
• Remove food and shelves from the freezer area for access and safe handling
• Installation typically requires basic hand tools; support the door during removal/installation to avoid injury or damage
• If the door contains glass or trim, handle carefully.