Kenmore Dryer 110.79822800 (11079822800, 110 79822800) Parts

I wanted to avoid pulling the drum. Luckily, my blower was easily accessed by pulling the front bottom panel. A couple of sheet metal screws were all I needed to remove the fan housing cover. I knew the fan was on reverse threads, i.e. righty-untighty. As it spins it tightens so no need for a retaining nut. I took off a screw holding on the exhaust tube and wiggled it out. I found the broken teeth inside. With the tube out of the way I was able to slide a crescent wrench in back and place... Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

Originally the dryer was squeaking a lot, so I purchased a new belt tensioner, but the original tensioner was an old-style no wheel tensioner, so that wasn't the source of the squeaking. I saw a lot of lint had built up inside the unit where there shouldn't have been that much. So I viewed a few videos on the Appliance Pros site and saw that the rear wheel guides were the cause of the squeaking and the rear felt drum and blower housing seal needed to be replaced. The rear blower housing was... Read more

Watched You tube videos to narrow the problem down to old deteriorated gaskets. Read more

Replaced the Rollers, Pins, belt and belt tensioner. One thing to keep in mind. In the video it was said that the back and front roller pins were different by lengths. They were the same length for my model. The differences were found to be the rear pins have left handed threads and the front ones were standard right hand threads. Keep that in-mind when you are trying to remove them. Read more

Purchased, Igniter Kit, Gas Valve Coil Kit, and as a precaution Thermal Fuse and Cutoff-Tml. Was pretty confident the problem was the gas valve coil, but figured that why not just replace the other items while I had the unit apart. Researching and utilizing this site certainly helped me out in figuring what the problem may be. Watched the instruction videos which were very detailed and helpful. The replacement and repair was not that difficult and the work was done rather quickly. Doing... Read more

Checked thermal fuse, belt pulley switch, door switch, and motor windings (primary 2.3 ohms start 2,2 ohms). Called Appliance Pros, told them my problem. They said that it appears to be the motor even though the ohm readings seam Ok and that I could return the motor if it was not the problem. I ordred the motor and blower wheel. Installed the new motor and everything worked! The only difficult part was that the motor blower had to be chiseled out. Their motor repair video was a great help. Read more

Replaced the duct tape with a new switch Read more

Replace the drum drive belt and tension pulley assy. Read more

I purchased the lid latch assembly and the lid switch strike. Following the clear video instructions for each part, my handy teenage son was able to remove the lid latch assembly and replace it with the new part as well as the lid switch strike. The washer is back to working perfectly for under $100. Appliance Parts Pros carry the parts to repair and at a lower cost than other online retailers. I saved about $30 compared to the other online site and I saved a service call fee. I'm so glad I... Read more

Replaced Read more

Replaced the Rollers, Pins, belt and belt tensioner. One thing to keep in mind. In the video it was said that the back and front roller pins were different by lengths. They were the same length for my model. The differences were found to be the rear pins have left handed threads and the front ones were standard right hand threads. Keep that in-mind when you are trying to remove them. Read more

Bought the leveling feet and screwed them in the bottom and they work great. Read more

• Will not agitate
• Pumps but will not spin
• Will not tumble
• Noisy

Upon removal of the lower inspection panel on the front of the machine, my 20 year old son thought the motor was bad by the smell. But he did discover what turned out to be the belt tensioner pulley laying inside the machine. After he pronounced it dead, without a thought to the idler pulley, I looked at the machine and determined the lack of movement was due to the idler pulley having "fallen" off the shaft by looking at the illustrated parts break down provided on this website. Ordered the... Read more

Replaced It With New One Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more