Kenmore Dishwasher 363.15452992 (36315452992, 363 15452992) Parts

Size: 8-18 x 7/8 inch.

White. 8-18 x 5/16 inch.

The Lower Dishrack is an OEM part for GE dishwashers. It provides a sturdy shelf for placing pots, pans, plates, and other dishware on the bottom level of the dishwasher interior. The lower dishrack supports dish loads, holding them securely in place during the wash cycles. 

Causes of a failing lower dishrack include long-term wear and tear, corrosion from exposure to water and detergents, damage from improper loading, and loose or broken components.

Symptoms of a bad lower dishrack:

• Difficulty sliding the rack in and out
• The rack getting stuck mid-cycle
• Broken or missing wheels/rollers
• Rust formation
• Bent or misshapen wires

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This timer cover is the replacement trim that surrounds and protects the dryer or washer control timer on the control panel, restoring a finished look and shielding the timer mechanism from dust and debris. What it does:

• Replaces a cracked, faded, or damaged timer trim to improve appearance and protect the underlying timer assembly
• Helps keep lint, dust, and moisture away from the timer control area
• Restores correct alignment and mounting for the timer knob and control components
• Useful when the existing cover is loose, broken, or missing

• One timer cover

• Disconnect power (unplug or switch off breaker) before starting any repair
• Remove the control panel or access bezel per your model's service instructions to reach the timer cover
• Use appropriate hand tools (screwdriver) and avoid forcing plastic tabs to prevent breakage

Replace a damaged upper/top dishrack to keep cups, glasses, and bowls secure and organized on the top level of your dishwasher. Restore smooth loading and dependable support when the original rack is rusted, bent, or broken.

• Holds and organizes items on the dishwasher's upper level
• Slides on the rail system for easy loading and unloading
• Helps prevent items from tipping during the wash cycle
• Replaces a rack that is rusted, deformed, or has broken/missing tines

• Disconnect power and water supply before servicing for safety.
• Open the door, extend the rack, and release the rack stops/end caps per your model.
• Remove the old rack; transfer any removable accessories from the old rack if applicable.
• Set the new rack on the rails, reinstall the stops/end caps, and verify smooth travel.

The spray arm assembly distributes pressurized wash water through its jets and rotates to clean dishes. If it's cracked, clogged, or not turning freely, replacing it restores proper spray coverage and cleaning performance.

• Directs water through jet openings to wash dishes throughout the tub
• Rotates by water force for even spray coverage
• Common symptoms: poor cleaning results, arm not spinning, visible cracks/warping, or clogged holes
• May cause unusual knocking if the arm is loose or contacting items

• Disconnect power and turn off the water supply before servicing
• Remove the lower rack; release the existing spray arm from the center retainer (method varies by model)
• Clear any debris from the pump outlet and seating surface
• Seat the new arm fully and ensure it spins freely before running a test cycle

This upper dispenser trim—commonly called the top tower—replaces the visible upper cover at the refrigerator dispenser area to restore appearance and proper fit. It protects internal dispenser components and keeps the dispenser edges clean and aligned. What it does

• Covers and protects the upper portion of the dispenser tower and its internal components
• Helps maintain a consistent, finished look at the dispenser opening
• Prevents dirt and moisture from reaching internal dispenser parts
• Can reduce rubbing or misalignment of the dispenser fixture that can cause noise or wear

• One upper dispenser trim (top tower) as shown

• Remove power to the appliance before starting work to avoid electrical hazards
• Typically secures with clips or a few screws—gentle prying with a trim tool may be required
• Inspect adjacent trim and fasteners for wear and replace as needed for a proper fit

This cam timer is the mechanical control that sequences an appliance's cycles, restoring correct timing and function when the control knob stops advancing. Replace a worn or stuck timer to recover proper cycle progression and operation. What it does:

• Advances cycle stages by rotating cams that open and close control contacts
• Sends timed signals to motors, switches and circuits to start and stop functions
• Common symptom: cycles won't advance or unit stays stuck in one cycle
• Common symptom: timer won't turn or control knob feels loose/slips

• One replacement cam timer assembly

• Disconnect power before servicing to avoid shock or injury
• Access usually requires removing the control console or rear panel; use proper tools
• Note original timer position and knob alignment before removal for correct reassembly
• Test appliance through a full cycle after installation to ensure proper operation

2 wire insulator.

This is a replacement fastener screw used to secure panels and components on compatible appliances, restoring proper fit and reducing movement. It's a simple, direct replacement when an original screw is missing or damaged. What it does:

• Secures access panels, covers, or internal components to prevent rattling and movement
• Helps maintain proper alignment of parts so doors and panels close correctly
• Replaces missing, stripped, or broken screws that can cause loose parts or noise
• Restores the appliance's original fit where a matching OEM fastener is required

• One replacement screw

• Turn off and unplug the appliance before starting any repair
• Use the correct driver and avoid over-tightening to prevent stripping threads
• If the original screw was holding electrical components, ensure power is disconnected and follow OEM safety instructions