Kenmore Refrigerator 363.9557814 (3639557814, 363 9557814) Parts

Replaced the water supply valve...boom! Read more

I watched the help videos first, then ordered the parts, and installed all items as in the video. Read more

Spliced new and old power cord near the connections in the fridge and connected them. Didn't mess with the factory harnesses or connections inside actual fridge. Read more

The auger gearbox shaft had a spot that was stripped of threads which prevented the auger drive from spinning the ice down the chute. I replaced the auger motor/gearbox assembly, the auger drive as it had to be cut off the shaft, and the 3 mount bolts that hold it all in place. Whole job took 30 minutes from start to finish which included cutting off the drive bracket. Read more

This part was easy to install by following the directions from other users here. As long as you get the right hoses connected in the right places, everything else was straight forward. Takes a few minutes for the tank to initially fill and pressurize and clear the air in the line and then you're on your way to clean fresh water! Read more

• Leaking

Replaced original (18 yrs.) 1/4" plastic tubing, clamp and grommet (AppliancePartsPros/GE parts) from outlet of ice maker water control valve to ice maker inlet. Also replaced water supply line to inlet of water control valve with new, GE braided, PEX 1/4" supply line with pre-attached female compression fittings on both ends. Repair job with AppliancePartsPros parts from outlet of water control valve went perfectly well, was simple, and had no leaks when tested. Parts were easy to install,... Read more

I ordered a replacement auger from AppliancePartsPros.com. Upon receipt of the new auger, I watched the repair video and took the ice crusher apart. I found several other parts that needed to be replaced as well. Once All the parts were received, I again watched the video. The video was not specific enough to show how to reassemble the ice crusher blades and the two types of washers. I found another video on YouTube that walked me through specific details of assembly and everything went... Read more

Easy fix once I found the problem. Broken solenoid sleeve. Part cost $2.58 + shipping. 10 minute repair. Read more

Hired a repair professional. This is an expensive fridge so I wanted to repair rather than replace. The estimated cost for the repair was quite high, but at least it was itemized. I went on-line and found Appliance Parts Pros, and bought the major plus one minor part from them. I arranged with my local repair guy to use the parts I bought on-line. RESULT: I saved $370 by buying my own parts, probably could have saved more with a little more effort. Appliance Parts Pros was easy to deal with,... Read more

This was a very easy repair, the on-line video at AppliancePartsPros.com was helpful. The Helix was spinning freely (meaning, the Auger Blade was not holding it in place on the Auger). Pulling the assembly apart was a snap, and very logical (the video is perfect if you get lost). The family is now enjoying both crushed and cubed ice - and the redesign of the Auger Blade seems to prevent clogging in the ice shoot. Read more

Changed the part with SS part. Read more

When we inspected the first time we found that Plactic had broken from the spiral part that for wards the ice. Also there were cracks in two places of other parts. There was a hole in the bottom of the bin. The new spiral was assembled and two new parts were replaced with help from the video and the diagram and the unit worked well. Two months later, ice maker would not forward any ice though the bin was full. We emptied the bin sand have ordered a new part or two in hopes that they will... Read more

We bought a used fridge and forgot to get the hardware to mount the doors. Looked up the model on your website. Using the pictures I was able to order just the parts I needed and not to duplicate anything (or leave anything out!). The parts arrived and because I watched the "how to" video I knew to use the "trick" to hold the doors up while attaching the hardware. Had the doors mounted in less than 15 minutes!.. Thanks Read more