Kenmore Range 629.20245 (62920245, 629 20245) Parts

The Grease Filter is an OEM part for Whirlpool range hoods. It is designed to capture grease and particulates from the air during cooking, preventing them from accumulating on kitchen surfaces and within the ventilation system. The filter measures approximately. 6-1/4 inches x 15-1/2 inches.

Causes of a bad grease filter can include accumulation of grease and food particles over time, damage from frequent cleaning, or wear and tear from regular use. A clogged or damaged filter can impede the performance of the range hood and reduce air quality in the kitchen.

Symptoms of a bad grease filter include:

• Reduced ventilation efficiency
• Excessive grease buildup on kitchen surfaces
• Unpleasant odors lingering after cooking
• Visible damage or clogging in the filter

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This is a complete plug-in cooking module for compatible Jenn-Air/Whirlpool modular cooktops. It drops into the cooktop bay and provides a pair of electric coil burners so you can swap configurations as needed.

• Provides two electric coil surface elements within a self-contained module
• Restores heating performance when a cartridge is damaged or not heating
• Symptoms can include no heat, uneven heating, or visible damage to the module
• Designed to plug into the cooktop's cartridge receptacle for quick changeovers

• Disconnect power before servicing
• Allow the cookware and module to cool completely before removal
• Lift out the old cartridge straight up; align and seat the new module fully into the receptacle
• Test each burner on low and high to ensure proper operation

The Broil Pan Set is an OEM part for Whirlpool ovens. This set includes a broil pan and an insert, designed to catch drippings and ensure even heat distribution during broiling, allowing for perfectly cooked and crisp results.

Causes of a bad broil pan set can include prolonged exposure to high temperatures, which may lead to warping or distortion of the pan. Additionally, frequent use without proper cleaning can result in rusting, chipping, or buildup of residues that compromise the pan's functionality and safety.

Symptoms of a bad broil pan set include:

• Warping or bending of the pan
• Presence of rust or corrosion
• Surface chipping or flaking
• Difficulty in achieving even cooking results

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Screw is an OEM part for Whirlpool appliances. This specific screw is used in various locations within Whirlpool appliances, securing components and ensuring the stability and proper alignment of parts. It is designed to fit precisely and maintain a firm hold, contributing to the overall functionality and safety of the appliance.

Over time, screws can become worn or stripped due to regular use, corrosion, or over-tightening. 

Causes of a bad screw include wear and tear, exposure to moisture leading to rust, and over-tightening which can strip the threads.

Symptoms of a bad screw include:

• Loose or wobbly components
• Misalignment of parts
• Noise due to vibrating or loose parts
• Difficulty in securing or removing the screw

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This 10-32 machine screw secures panels, brackets, and internal assemblies in your appliance. Replacing missing or stripped hardware restores a tight, rattle-free fit and helps keep components properly aligned.

• Provides a threaded fastener for metal-to-metal connections
• Helps maintain correct alignment of panels, brackets, and housings
• Replaces missing, rusted, or stripped screws
• Symptoms include loose or vibrating panels, gaps/misalignment, or hardware that won't tighten

• Disconnect power (and shut off gas/water, if applicable) before servicing
• Match the 10-32 thread and length to the original screw for the location
• Start by hand to avoid cross-threading; tighten snugly without over-torquing
• Retain and reinstall any original clips, spacers, or washers used in your model

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

This is the electric broil element for your oven. It delivers high, direct heat from the top of the cavity to sear and brown foods, restoring proper broiling performance when the original element has failed.

• Provides radiant heat from the top of the oven during the Broil cycle
• Restores proper searing and browning performance
• Common failure symptoms: no heat on Broil, weak or uneven broiling, element won't glow red, visible blistering or breaks
• Direct replacement for a failed or damaged broil element

• Disconnect power at the breaker or unplug the appliance; allow the oven to cool completely
• Remove oven racks, take out element mounting screws, and gently pull the element forward to access the wires
• Transfer the wires one at a time; ensure terminals are fully seated and do not let wires slip back into the insulation
• Reinstall the element without bending it, tighten screws snugly, restore power, and test the Broil cycle

This oven door seal forms a heat-resistant barrier around the door opening to keep heat in and stabilize temperatures. Replacing a worn seal helps restore proper door closure, efficient heating, and consistent baking performance.

• Seals the gap between the door and oven front to prevent hot air and steam from escaping
• Helps maintain stable cavity temperature and more even cooking results
• Replace if the seal is torn, frayed, hardened, flattened, or if you notice heat escaping, longer preheat times, or temperature fluctuations

• Disconnect power or gas and allow the oven to cool completely before servicing
• Open the door, remove the old seal, and clean the channel or retainers
• Press the new seal into the existing clips/retainers without stretching; align corners evenly
• After installation, verify the door closes snugly and perform a brief preheat to help seat the seal

This terminal block is the insulated connection point where the appliance's incoming power ties into the internal wiring. Replacing a heat-damaged or loose block restores a safe, reliable electrical path and helps prevent arcing and intermittent power loss.

• Connects the supply conductors to the unit's internal wiring
• Provides insulated posts to securely fasten and distribute power
• Helps maintain tight, low-resistance connections
• Common failure signs: melted/discolored plastic, burned or loose terminals, arcing, scorching, or intermittent/no power after confirming the cord and breaker

• Disconnect power at the breaker or unplug the appliance; verify no voltage before servicing
• Photograph or label wire positions to ensure correct reassembly
• Inspect and replace any heat-damaged wire ends or lugs; use appropriate terminals
• Tighten connections securely and ensure wires are fully seated and strain-relieved as originally installed

Spark electrode with a 29 inch female terminal.

This bake element is the lower-oven heating source that brings your range or wall oven up to temperature for consistent baking. Replace a burned or damaged element to restore reliable preheat and even cooking results. What it does:

• Provides bottom heat during bake cycles for even, consistent cooking
• Primary heat source for preheating and maintaining set temperature
• Common symptoms: no heat in bake, slow preheat, won't reach temperature, uneven baking, visible blisters/breaks on the element
• Useful clue: broil works but bake does not

• 1 bake element

• Disconnect power at the breaker before servicing
• Remove racks; take out element mounting screws; pull element forward to access terminals
• Transfer wires one at a time and ensure tight, insulated connections; don't let wires retract into the cavity
• After reassembly, run a brief bake test to verify operation and clear any residual smoke from first heat-up

This radiant cartridge is the plug-in cooking surface used on Designer Line modular cooktops. It restores a smooth black surface and consistent, even heat when the original cartridge is damaged or no longer heating properly.

• Provides radiant heat beneath a smooth glass surface for everyday cooking tasks
• Self-contained plug-in module that seats in the cooktop bay and delivers heat to cookware
• Common symptoms prompting replacement: no heat, uneven or intermittent heat, or visible cracks/discoloration on the surface
• Restores normal heating performance when matched to a compatible modular cooktop

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• Lift out and unplug the old cartridge straight up; avoid prying on the glass surface
• Inspect and clean the receptacle; align and firmly seat the new cartridge until fully engaged
• Restore power and test heating at low and high settings using appropriate cookware

This blower wheel mounts on the drive motor and pushes air through the dryer drum and out the exhaust. Replacing a worn wheel restores proper airflow for consistent drying and helps prevent overheating and nuisance shutdowns. What it does:

• Moves air across the heater, through the drum, and out the vent to remove moisture
• Helps maintain proper airflow and temperature inside the dryer
• Common failure symptoms: reduced or no airflow at the exterior vent, longer dry times, unusual scraping/thumping or vibration from the blower area, or overheating/shutoff
• Cracked fins or a stripped hub can cause the wheel to slip on the motor shaft

• 1 blower wheel

• Disconnect power and turn off gas supply before servicing
• Access the blower housing per your model's service instructions; remove the retaining hardware and replace the wheel in the same orientation
• Clean lint from the blower housing and vent path; inspect the motor shaft and blower seal for wear
• Reassemble and verify the wheel spins freely without rubbing; check airflow at the exterior vent

This plug-in coil cartridge restores reliable surface heating on compatible modular cooktops. Replace a worn or damaged module to regain consistent burner performance and maintain a matching black finish. What it does:

• Provides electric surface heat via a self-contained coil cartridge that plugs into the cooktop receptacle
• Helps resolve issues like a surface burner not heating or heating intermittently
• Addresses problems from visible damage or burned/loose cartridge terminals
• Preserves proper fit and appearance for black-finish cooktops

• 1 coil cartridge assembly

• Disconnect power at the breaker and allow the cooktop to cool completely
• Lift out the old cartridge; inspect the cooktop receptacle for heat damage before installing
• Align guides and terminals; seat the cartridge fully without forcing the connection
• Restore power and test burners at low/medium settings first

This radiant element cartridge replaces the plug-in cooking module on modular electric cooktops. It restores a smooth, even-heating surface and installs by seating into the cooktop receptacle, bringing damaged or non-heating modules back to reliable service.

• Provides radiant heat beneath a glass-ceramic surface for everyday boiling, simmering, and frying
• Plugs into the cooktop's cartridge receptacle on modular electric units
• Restores performance when the existing cartridge is cracked, damaged, or not heating consistently
• Black finish matches black cooktop designs

• Disconnect power at the circuit breaker before servicing
• Allow the cooktop and old module to cool completely; handle glass carefully
• Lift the old cartridge straight up to disengage; align and fully seat the new cartridge in the receptacle
• Restore power and test all heat settings