Kenmore Dishwasher 665.13933K010 (66513933K010, 665 13933K010) Parts

Color: Black. Screw for lower toe panel. For Biscuit screw use 3400865, for white screw use WP3400836.

This OEM replacement part is sourced directly from the manufacturer and is a spray arm for dishwashers. The spray arm is the component that rotates and disperses water throughout the dishwasher tub allowing the dishwasher to perform its essential functions of cleaning dishes. If the spray arm is no longer spraying water effectively or the dishes are not coming out clean, the spray arm might need to be replaced. Luckily, replacing this part is a relatively simple process. To begin this repair, make sure that the dishwasher is unplugged. Then proceed to open the dishwasher door and remove the lower dishrack. Using a screwdriver, unthread the main screws that hold the spray arm in place. Once loosened, proceed to unmount the main mounting bolt that secures it to the bottom of the dishwasher. After that, set the old spray arm to the side and thread the main bolt and individual screws that hold the spray arm in place. This genuine replacement part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand dishwashers.

The Screw Hole Cap is an OEM part for Whirlpool dishwashers. It covers the screw holes, providing a clean and finished appearance while preventing moisture and debris from entering the screw openings. This helps maintain the dishwasher's aesthetic and ensures that screws remain protected from rust and corrosion.

Causes of a bad screw hole cap can include regular wear and tear, accidental impacts, or misplacement during maintenance.

Symptoms of a bad screw hole cap include:

• Missing or loose caps
• Moisture or debris accumulating in screw holes
• Visible wear or damage to the caps

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Shaft seal included.

The Steam Vent is an OEM part for Whirlpool dishwashers. It is designed to allow steam to escape from the dishwasher during and after the washing cycle, preventing excessive moisture buildup inside the appliance.

Causes of a bad steam vent can include clogs due to mineral deposits or food particles, damage to the vent mechanism from repeated use or accidental impact, and wear over time that affects its sealing capability. A malfunctioning steam vent can disrupt the dishwasher’s drying process and lead to poor performance.

Symptoms of a bad steam vent include:

• Excessive moisture or condensation inside the dishwasher
• Poor drying performance
• Noticeable steam escaping from areas other than the designated vent
• Unusual noises during the drying cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This dual tine positioner secures two rack tines together to keep dishes stable and properly spaced during the wash. Replacing a cracked or missing clip helps prevent plates and lids from tipping or rattling. What it does:

• Holds two adjacent rack tines in the selected position
• Helps maintain spacing for plates, lids, and trays
• Restores stable loading when the original clip is worn or broken
• Common symptoms: broken/missing clip, tines won't stay upright, items tip over or rattle

• One dual tine positioner clip

• Slide the rack out; remove the old clip by releasing its tabs
• Align the new clip over two tines and snap it firmly into place
• Spin the spray arm by hand to confirm clearances before running a cycle

The Hex-Head Screw is an OEM replacement part for use in Whirlpool dishwashers. This metal screw measures approximately ¾ inch long. Its primary purpose is to secure the dispenser bracket in place, ensuring stable operation. This hex-head screw is designed for use with compatible hexagonal tools. This makes installation and removal straightforward. This part is sold individually and is guaranteed to fit your dishwasher door panel. This screw is compatible with select Whirlpool brand models including Amana, Crosley, Estate, Inglis, Jenn Air, Kenmore, Kitchen Aid, and Maytag.

The Power Cord Kit is an OEM replacement part for Whirlpool dishwashers. It is a 3-prong grounded, 16-gauge cord that includes all the hardware needed for installation. Includes all hardware needed for installation.

Causes of a bad power cord can include normal wear and tear over years of use, accidental impacts or cuts to the wiring, or improper installation that damages components.

Symptoms of a bad power cord include:

• The dishwasher not turning on or completing cycles
• Warm or hot power cords during operation
• Frayed, cracked, or exposed copper wiring

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

This factory screw secures appliance components. It restores a tight, reliable hold when the original hardware is stripped, missing, or corroded—helping prevent vibration and keeping panels and brackets properly aligned.

• Provides threaded fastening for panels, brackets, covers, or internal components
• Replaces worn, rusted, stripped, or missing hardware
• Helps reduce vibration and rattling from loose parts
• Restores proper alignment and a secure fit of attached parts

• Disconnect power; turn off water supply before service
• Note original screw location and retain any spacers or clips for reassembly
• Start threads by hand to avoid cross-threading
• Tighten snugly; do not overtighten to prevent stripping

Quantity of ONE. Size: 8-18 x 5/8 inch. (#8 screw, 18 threads per inch, 5/8 inch long)

Color: Grey. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For white use WP676453. For tips use 676458.

This small clip secures the guard/shield on the dispenser assembly. Replacing a cracked or missing clip keeps the guard firmly attached and aligned so the dispenser operates properly without interference, noise, or premature product loss. What it does:

• Fastens the dispenser guard to its mounting point on the dispenser assembly
• Keeps the guard aligned to prevent interference with dispenser door/flow
• Restores a secure fit if the original clip is cracked, deformed, or missing
• Common symptoms: loose or missing guard, rattling, incomplete dispensing or residue left after a cycle

• 1 dispenser guard clip

• Disconnect power to the appliance; turn off water supply if applicable
• Open access, support the guard, and release the worn clip from its tabs
• Snap the new clip fully into place, ensuring it engages all locking points
• Ensure the guard is secure and that the dispenser door/flow path is unobstructed before use

Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679

Replace a damaged or missing silverware basket with this dishwasher basket. It organizes and separates flatware and small utensils so water can reach each piece, improving cleaning results and keeping items contained throughout the wash.

• Holds and separates silverware and small utensils during the dishwasher cycle
• Helps keep pieces upright for better spray coverage and cleaning
• Replace if the basket is cracked, warped, or has broken grid sections that let utensils fall through
• Also replace if missing or if the basket no longer stays securely in place

• Turn off power to the dishwasher before working inside
• Remove the old basket and place the new basket in the designated location for your model
• Ensure spray arms rotate freely with the basket installed
• Load utensils per your owner's manual for best results

This factory-specified screw secures panels, brackets, and internal components in your appliance. Replacing worn or missing hardware restores a tight fit to help reduce vibration, noise, and premature wear.

• Fastens sheet metal, brackets, or plastic parts as designed by the manufacturer
• Helps maintain alignment and reduce vibration/rattling
• Direct replacement for stripped, corroded, or missing screws
• Common signs: loose panels or trim, shifting components, screw won't tighten

• Disconnect power; shut off water or gas supply if applicable
• Use the correct driver to avoid stripping the head
• Start threads by hand to prevent cross-threading; tighten snugly without overtightening
• Replace one-for-one in the original location per service information

This heater terminal nut fastens the heating element's electrical connector to its stud, keeping the connection tight under heat and vibration. Replacing a worn or missing nut restores safe contact and consistent heating performance.

• Secures the wire/ring terminal to the heater stud for a solid electrical connection
• Helps prevent arcing, discoloration, and heat damage from a loose connection
• Signs include a loose terminal, burnt odor, or melted/charred insulation at the heater connection

• Disconnect power and allow the appliance and element to cool completely before service
• Photograph wiring for reference; remove old hardware and clean the terminal
• Inspect the ring terminal, insulators, and stud; replace any heat-damaged components
• Start threads by hand to avoid cross-threading; snug with the correct nut driver—do not overtighten