Kenmore Dishwasher 665.13939K012 (66513939K012, 665 13939K012) Parts

This heater terminal nut fastens the heating element's electrical connector to its stud, keeping the connection tight under heat and vibration. Replacing a worn or missing nut restores safe contact and consistent heating performance.

• Secures the wire/ring terminal to the heater stud for a solid electrical connection
• Helps prevent arcing, discoloration, and heat damage from a loose connection
• Signs include a loose terminal, burnt odor, or melted/charred insulation at the heater connection

• Disconnect power and allow the appliance and element to cool completely before service
• Photograph wiring for reference; remove old hardware and clean the terminal
• Inspect the ring terminal, insulators, and stud; replace any heat-damaged components
• Start threads by hand to avoid cross-threading; snug with the correct nut driver—do not overtighten

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This compression tube nut secures water inlet tubing to a threaded fitting to create a reliable, leak-resistant seal. Replace a cracked or stripped nut to stop drips at the connection and keep your appliance's water system working properly.

• Compresses the tubing against the fitting to seal the water line at the inlet valve, filter head, or other water-system connections
• Helps correct leaks at the water line connection point
• Replaces nuts that are cracked, cross-threaded, or deformed
• Common symptoms: water dripping at the connection, difficulty tightening the line, or a poor seal after reassembly

• Shut off the water supply and disconnect power before servicing.
• Slide the nut onto the tubing first, seat the tube fully on the fitting, then hand-tighten and snug with a wrench; do not overtighten.
• Inspect and reuse the existing sleeve/ferrule and tube insert if in good condition; replace if worn.
• Restore water and check for leaks at the connection.

This replacement shield fits over the heater/probe area to provide a protective barrier. It helps prevent direct contact and excessive radiant heat exposure, protecting nearby components and supporting accurate temperature sensing for consistent operation. What it does:

• Shields the heating element and adjacent temperature probe/sensor area
• Helps prevent heat damage to nearby plastics, wiring, and components
• Reduces the chance of items contacting or striking the heater/probe
• Common signs it's needed: cracked, warped, or missing shield; discoloration; rattling or an exposed probe/heater area

• 1 shield

• Disconnect power and allow all heated parts to cool before servicing
• Access the heater/probe area and note the original shield orientation
• Seat the shield fully; secure with existing clips/fasteners if applicable
• Verify clearances around the heating element before restoring power

The door balance mount is the side-frame bracket that supports the dishwasher's door counterbalance system. When worn or broken, it can let the door drop, slam, bind, or feel heavy. Replacing it restores smooth, controlled door movement. What it does

• Anchors the door springs and balance link/cable to counterbalance the door's weight
• Helps the door open and close smoothly without dropping or slamming
• Guides the balance link for consistent, quiet movement
• Common symptoms: door feels heavy or uneven, falls open, won't stay put, or makes grinding/squeaking noises; visible damage to the bracket or rollers

• One door balance mount (bracket)

• Disconnect power and shut off water before servicing
• Pull the dishwasher out slightly to access the side where the mount is installed
• Carefully relieve spring tension; note link/cable routing before removal
• Transfer the spring/link to the new mount, secure the bracket, and check door balance on both sides

This vent door bezel is the trim piece that frames the vent opening on the dishwasher door. It restores a clean, finished look and helps keep the vent assembly properly seated if the original bezel is cracked, loose, or missing.

• Mounts on the exterior of the door around the vent outlet
• Provides a finished edge and helps retain the vent assembly/gasket
• Replaces damaged or missing trim that won't stay attached
• Common symptoms: broken tabs, loose or rattling vent trim, visible gap or cosmetic damage around the vent

• Disconnect power to the appliance; turn off water supply if needed
• Open the door and remove fasteners to access the vent area behind the panel
• Release the old bezel (tabs/screws), align the new bezel, and secure flush to the panel
• Do not overtighten fasteners; avoid vibration or leaks

This feed tube assembly channels wash water from the pump to the upper spray system. Replacing a cracked or obstructed tube helps restore upper-rack cleaning performance and can prevent leaks at the back of the tub. What it does:

• Routes water from the circulation pump to the rear manifold/upper spray system
• Helps maintain proper spray pressure for upper-rack washing
• Addresses visible cracks, broken locking tabs, or mineral buildup on the tube

• 1 feed tube assembly

• Disconnect power and shut off water to the dishwasher before servicing
• Remove racks as needed; release retaining tabs/clips and detach the tube from its connections
• Inspect and reuse existing seals/clips only if in good condition; replace worn seals
• Ensure the tube is fully seated and latched at all connection points before reassembly

This inner door seal forms a moisture barrier between the dishwasher tub and the door assembly, helping keep wash water and steam contained. Replacing a worn seal can stop drips at the door and protect internal components.

• Seals the joint along the inner door to contain wash water and steam
• Helps prevent door-area leaks or drips during cycles
• Blocks moisture from entering the door cavity where electrical parts reside
• Common signs: water at the bottom/sides of the door, damp control area, visible wear/flattening or tears on the seal

• Disconnect power and turn off water supply before servicing
• Open the door and remove perimeter screws to separate inner/outer door panels
• Remove the old seal; clean the mounting surface and note seal orientation
• Press the new seal firmly into place, reassemble, and run a leak check

This is a Whirlpool control board intended for use with dishwashers.The control board is a critical component of the dishwasher as it controls the cycles and functions, including the draining and drying cycles. Control boards are subject to wear and tear that can render them ineffective and require them to be replaced prior to the standard lifecycle of the appliance. Unplug the dishwasher from both the power and water sources before attempting to replace the control board to prevent serious electrocution injuries. Work gloves should also be worn.This OEM control board has been sourced from the manufacturer and is compatible with dishwashers from Whirlpool, Maytag, Kitchenaid, Magic Chef, Admiral, Norge, and other brands. This part has been made from high-quality, durable, non-corrosive materials and is only sold individually.

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

This replacement screw secures appliance components, panels, and brackets. It restores a tight, reliable hold when an original fastener is missing or damaged, helping eliminate rattles, gaps, or shifting parts.

• Fastens two or more parts together inside the appliance
• Helps keep panels, brackets, or trim securely in place
• Can reduce vibration, rattling, or loose handles caused by missing/loose screws
• Replaces worn, stripped, or corroded fasteners

• Disconnect power and shut off water supply before servicing
• Match location and orientation to the original fastener
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to prevent stripping or cracking

12 Ft in length

Includes two screws, two clamps, and undercounter mounting brackets.

This spray arm distributes wash water inside the dishwasher, rotating to deliver even spray coverage across the racks. Replace a cracked or clogged arm to restore consistent cleaning performance and reliable water distribution.

• Directs pressurized water through jet openings while spinning to wash dishes evenly
• Helps address symptoms such as poor cleaning results or uneven spray coverage
• Replace if the arm is cracked, warped, mineral-fouled, or no longer spins freely
• Damage or improper seating can cause the arm to strike dishes/tub and make noise

• Disconnect power to the dishwasher before servicing
• Remove rack(s) if needed; release the arm by unscrewing the retainer or pressing the locking tab (method varies by model)
• Clean debris from the mounting hub and seal surfaces before installing the new arm
• Seat fully, ensure the arm spins freely with proper clearance, then run a test cycle

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.