By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
Need Help?
Call
This electric pump is responsible for draining water out of the washer tub during the drain and spin cycles. It pumps used wash and rinse water through the drain hose and out of the machine. Replace this pump if your washer fails to drain, drains slowly, makes loud humming or grinding noises during the drain cycle, or if you find water remaining in the tub after a completed cycle.
Very simple repair really. Unplugged the washer, moved the washer in order to have access to the back panel. Remove 13 #20 torx screws holding the back panel on ; then removed back panel. Open the filter access on the front bottom of the washer to drain any remaining water, be sure to have a towel ready, as if the pump is bad, there's bound to be quite a bit. Looking at the washer from the back, the bottom left contained the pump. Remkve the two electric connectors and move out of the way.... Read more
Usually ships within 4 - 14 days
Fixes weak spray or slow draining caused by a worn impeller. Restores water circulation in your dishwasher. Moderate DIY repair with video guide.
I replaced the dishwasher circulation motor. I also replaced the impeller assembly, although it turns out that was not necessary. Actually replacing the motor was straightforward: Remove the upper and lower racks. Turn off the breaker and water supply. Disconnect power, supply water and drain hose. Slide out the dishwasher. Inside the dishwasher, unscrew the two screws holding on the bottom rotating sprayer and remove the sprayer, unscrew the one screw holding the little metal bracket and... Read more
Fixes dishwasher leaks and draining problems. This sump assembly collects and channels water to the drain pump. DIY repair typically takes 1-2 hours.
My project involved replacing the sump assembly and main motor on my LG dishwasher. The parts arrive in about 2-3 days. Wow, FAST! With the help of videos from LG I knew what to do. The trick with the whole project was ensuring that I transferred ALL gaskets from the old sump assembly to the new one. I missed transferring one around a sensor, then did not get the gasket around the pump motor properly. Once all those were correct all leaks stopped, new motor is whisper quiet (all I hear now is... Read more
Fix weak spray or poor cleaning caused by a cracked impeller. Simple 15-minute repair with basic tools. Restores water circulation and pressure.
The initial problem was just a simple blockage on the filter screen...until I dropped a screw. So, I had to take the rest of the insides apart to retrieve it. The original impeller would not come off easily, so I tried to pry it off. Naturally, that caused the threaded portion to break. The new impeller went on much more easily than the old one came off, and the dishwasher is back in action. Simple repair; there's really not much to the inside of this thing. Read more
Fix a dishwasher that won't drain or displays motor error codes with this drain pump motor assembly. Moderate DIY repair taking about 2 hours to complete.
The PC board was bigger than the original so had to modify the mounts, the pump and rotor are pretty straight forward but would have much easier with another pair of hands. It took about 2 hours start to finish. One and a half days to get the parts, fantastic service. A new dishwasher is $1300.00. the parts were $314.00, so more than worth fixing. Read more
Fix a washer that won't drain or shows error codes E03/E04. This drain pump removes water after each cycle. Moderate DIY repair with basic tools.
Replaced with part ordered. Exact fit. No problems. Thank you Appliance Parts PROS! Read more
This pump and brake assembly drains water from the tub and applies the basket brake in your top-load washer. Replacing a worn assembly restores proper draining and a safe, prompt basket stop between cycles. What it does
Upon opening the front cover of my GE washing machine, I found the water pump/brake was not spinning as it should when the drain/spin cycle was starting. I suspected that the pump/brake was the cause of the problem. I tried to turn the flywheel of the pump by hand and found it tight and somewhat difficult to turn. To temporarily fix the problem, I added a couple drops of motor oil to the front shaft and bearing to see if it would loosen up a little bit. Doing that and turning the flywheel by... Read more
Fix poor cleaning or standing water with this dishwasher food disposal unit. Grinds food particles to prevent clogs and improve wash performance.
Grinding noise during drying cycle? This vent door actuator opens and closes the dishwasher vent for proper airflow. Easy DIY fix, one screw install.
I ordered and replaced the 2 possible items that I believed could be the cause. Unit now operates correctly. Read more
Dishwasher not draining or water pooling at bottom? A cracked sump disrupts water flow to the pump. This housing restores drainage and prevents leaks.
Fixes dishwasher not draining or leaving standing water. This pump and motor assembly restores circulation and drainage when the motor clicks but won't turn.
Fix a washer that won't drain or leaves standing water with a new drain pump assembly. Moderately challenging repair that solves drainage issues.
This drain impeller spins inside the drain pump to move wastewater out of the appliance, restoring normal draining and reducing standing water. It's a direct-replacement pump impeller designed to fit the original pump housing. What it does:
Dishwasher not draining or stuck mid-cycle? This drain pump and motor assembly removes dirty water between cycles. Moderate DIY repair for most models.
Dishwasher not spraying water or dishes staying dirty? The circulation pump motor distributes water to spray arms. Moderate DIY repair, about 3 hours.
I did it myself. I replaced the impeller. It took me about three hours to do it Read more
This small motor actuates the detergent dispenser mechanism in the dishwasher, opening the dispenser door at the correct time during the wash cycle to release detergent. It is driven by the control board and uses a cam to unlatch the dispenser lid. Replace this motor if the detergent dispenser fails to open during the cycle, leaving the soap cup full or detergent undissolved.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.