Rc December 23, 2011 for Model Number S302ts My lower oven does not heat. The light works, sounds like it is on but does not heat on broil or below so I know it is not the coil. Is it the relay and which part?
1 Answer Hi Rc. OK there are a few checks that need to be taken before ordering parts. In between both cavities (mid plenum) beside the door latch is a safety thermostat. It will open if defective or if it senses too high of heat. This will stop element heating. It needs to be checked for closed continuity with an ohm meter. It is part # 00414633. The bake element is part # 00367648. The broil element is part # 00367647. They need to be checked for opens or shorts. They usually ohm out between 11-23 ohms. You need to also check to see if they are shorted to the mount itself. Check and make sure the 240 vac is tight at the terminal block. If all this is verified good, then really the control board kit is needed. If you do not get 120 vac out at the bake relay while it commands it for heat , then this is that part # 00702451 . Thank You. Read More...
Michael December 19, 2011 for Model Number Thermador S302TB The display on my oven has become very dim but everything functions without any problems. Please let me know whether or not replacing this AP4929089 will fix the problem. Thanks.
1 Answer Hello Michael. Yes, based on the information you provided, it sounds like the display kit 00702451 is bad and will need to be replaced. Hope this helps. Read More...
Jack December 06, 2011 for Model Number SCD302 Double oven. Lower oven works fine. Upper Preheats normally to approx. 200 degrees then all but stops. Bake element stops heating (glowing red). Changed Bake element with same results.
1 Answer Hello Jack. If the oven sensor 00414152 is good in the unit, then you will need to replace the oven display repair kit 00702451. Hope this helps. Read More...
Lisa November 26, 2011 for Model Number SCD302TP I ran a self clean cycle on my upper oven. When it was finished (or near finishing), it began to beep consistently and showed an FC on the panel. It would stop briefly by pressing OFF on the control panel, but to stop it entirely we had to flip the breaker. Once the oven completely cooled, the door unlocked, but the upper oven will not heat. The lower oven is fine. The fan works, lights work, and all of the display appears to work, but neither of the elements heat up.
1 Answer Hi Lisa. To the right is a oven thermostat that will open under a high heat situation. This part # is 00414633. Remove the power to check to see if is open with an ohmmeter. You can temporarily bypass this by jumping these 2 wires together and cover with electrical tape. Then turn on the power and see if the upper bake operates again. Thank You. Read More...
Richard October 26, 2011 for Model Number SC302TB Hello, I am planing in getting this kit and replace it, but the board looks to me so far in the back, how can I change the board? What will be the best way to approach it? Can I do it on the front or I will need to remove the double oven an do it for the back? Thanks
1 Answer Hello Richard. You will need to uninstall the wall oven and remove the top panel to access and replace the control boards 00702451. Once the top panel is removed, you can access the board with out problems. Hope this helps. Read More...
Steve October 04, 2011 for Model Number sc272t Your AP4929089 is this the relay board for the upper or lower oven? I need the board for the lower oven, they appear to be different.
1 Answer Hello Steve! For the regular oven use part number 00702451 and for the convection oven use part number 00369126. Thanks. Read More...
Mark K. September 25, 2011 for Model Number Thermador M# SCD302TS The oven is still operating but the LCD display is very weak?
1 Answer Hello Mark! It sounds as if the electronic control is shorting out and needs to be replaced. Your part number is 00702451. Thanks. Read More...
Tim F. September 14, 2011 for Model Number scd272tp Everything works great but the display does not light up. What part should I replace?
1 Answer Hello Tim. Based on the information you provided, it sounds like the display 00702451 is bad and will need to be replaced. Hope this helps. Read More...
Betsy H. June 30, 2011 for Model Number SC302TS sn99060043 I think the code on the display was F7 or F9 not sure. I did just buy an oven disp repair kit from your company!
1 Answer Hello Betsy. The F7 code is saying the control board is reading a shorted key. You will need to check and make sure the ribbon cable is seated properly. If it is an F9, you will need to check the door lock switches. Hope this helps. Read More...
Betsy H. June 29, 2011 for Model Number SC302TS SN99060043 My oven beeped alot, then we turned it off by the fuse box because it wouldn't stop beeping. Turned it back on and now only the oven light comes on and oven doesn't work.
1 Answer Hello Betsy! When the oven was making a beeping noise was there a fault code on the display screen? Thanks! Read More...