Dawn July 25, 2016 for Model Number FGHD2433KB1 Last week the only button that worked regularly was the start/cancel button. Occasionally, I could get another button to light. Now there are no lights except PF when I turned the machine off at the electric breaker for 30 minutes. The PF light goes out when the door is opened and no other codes light. Thanks
1 Answer Dawn, This issue sounds like it would be caused by a faulty control panel which is part number 154791803. Read More...
Mike June 29, 2016 for Model Number FGHD2433KB1 The Air Dry button is always lit, regardless of mode selected. Panel is responsive to various modes (LEDs light when selected), but air dry never goes out. Dishwasher will start/stop with door close without pushing buttons, though not predictably; sometimes it goes to the cancel mode (i.e. tries to pump out water) multiple times before going into wash mode on close. Door latch was just replaced, though it broke when I was out of town and for a couple of weeks people had been closing the door hard to get it to start. Control panel is certainly displaying wrong (constant air dry), but the automatic starting and stopping makes me suspect the board as well. Seems to cycle okay once I get it to start, though.
1 Answer Mike, It is a very good likelihood that this issue will be caused by a faulty control board rather than the touchpad being at fault. The main board could be signalling the air dry light. Read More...
Ed G June 28, 2016 for Model Number FGHD2433KF1 Yesterday we had a few short power outages, now when we start the dishwasher on the Quick Wash cycle ( 50 min) after 3-4 minutes the display reads 99 and runs thru the complete cycle. Any ideas??
1 Answer Hello Ed. Based on the information you provided, it sounds like the control board is bad and will need to be replaced on the unit. Read More...
Victor June 14, 2016 for Model Number GLD4355RFS2 All my button lighten up and flashing, with the front panel display 'er clean S'. Do you know what is going on? What part do I need to replace?
1 Answer Victor, The ER Clean S is indicative of a faulty keypad and you would want to replace the control panel which is part number 154639201. Read More...
Scullery May 23, 2016 for Model Number FGHD2465NF1A When I press the normal cycle, the small light comes on. Then I press the start area; the light does not come on. I close the door; the machine does not go on. If I almost close the door until the CL comes on THEN close the door the machine goes on. It washes the dishes no problem. Do I need a control console or just the circuit board? How are either one replaced? It is 7 months past the the 1yr warrantee. Thank you.
Sk May 03, 2016 for Model Number FPHD2481KF0 Am getting error "Er" followed by "uo" when washing cycle is going on. Not sure what that means. I replaced water inlet valve, but still it says the same error. Sometimes I get this error as soon as I start my cycle. Am also noticing when this appears there is some sort of periodic banging noise coming from top of the dish washer. So before I decide to get the control board wondering if pros can guide me in right direction of diagnosis.
1 Answer SK, The ER uo is a vent not closing error and would require a new vent assembly which is part number 154784401. Read More...
Roxann April 24, 2016 for Model Number Fgid2466qf4a Frig gallery dishwasher works just fine. My Led lights on the control panel are turned off. I do not remember which 2 buttons to press and hol to cone back on. Thankyou
1 Answer Roxann, You will want to press the power plus and rinse only simultaneously for approximately 8 seconds. Read More...
Heather March 19, 2016 I have a Frigidaire Gallery dishwasher. One day our electricity went out briefly. The display will light up when the door is open, but as soon as I shut the door the display goes blank. It used to stay lit up for the who,e cycle. Is there an easy fix?
1 Answer Heather, You will want to check the door switches on the unit to make sure that the switches are good. If the switches check ok then the issue will most likely be a faulty control board. Read More...
Phil March 18, 2016 for Model Number FGHB2433KBO I have lost all power to the unit, none of the lights or indicators are working. I have 110 volts to the control board and also on the door switches. Is my control board part #154815601 bad?
1 Answer Hello Phil, This is most likely the main control board under the cabinet. For a part number you will need to verify the model number from the units' I.D. tag since the model number provided does not come up as valid. Read More...
Demount March 10, 2016 for Model Number Frigidair dishwasher I can no longer choose a cleaning cycle, such as "Pots and pans", "both racks", etc. The DW seems to pick a cycle by itself and will not respond to any attempt to push another option. Not sure what part we need to replace.
1 Answer Hello Demount. You will need to order and replace the control panel on the unit. Read More...