Ron October 24, 2016 for Model Number FGHD2433KB1 Dishwasher starts to run then ER starts flashing no matter what setting. I was told control board or control panel? How can I find which one if either are bad or can it be something else?
1 Answer Hello Ron. If diagnostics do not pull anything up, you will need to replace the control board. It is a configuration error. Read More...
Amanda October 17, 2016 I ran my dish washer on normal wash and when it was finished the screen read, 'clean S' in red letters. What does this mean? It does not read 'er' on the screen.
1 Answer Hello Amanda, I'm sorry but we need to ask you to post a new question including the model number from the units' I.D. tag. This will enable us to pull specific information so we can provide you with accurate information. Thank you for your patience and understanding in this matter. Read More...
Lina October 01, 2016 for Model Number FDB4315LFC3 Dishwasher does not turn on. The control panel is off but never got an error message. We checked th circuit breaker and all the power works but the dishwasher will still not turn on or light up.
1 Answer Hello Lina. You will need to test and see if there is power coming to the control board. If there is power to the board and the unit is completely dead, you will need to replace the board 5304514670 on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Jar September 27, 2016 for Model Number Frigidaire dishwasher My dishwasher just stopped working. it started no problem, but then just stopped. No lights on front will even come on. I did check and there is power to door switch's and control panel. Could the panel be gone just like that.
1 Answer Hello Jar. Test for power to the control board. If there is power there, and the board does not work, you will need to replace the control board. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Francisco September 19, 2016 for Model Number FRIGIDAIRE DISH WASHER GALLERY 1- Brand new unit. The panel lights work only when door is open. Once door is closed lights go off. Once the cycle is complete, no lights go on, except for a blue light at the bottom of the unit. Is this normal? If it is, can I override it to turn lights on with the door closed? 2- The sides of the unit are very hot. I can touch it, but it is almost "hot to the touch"... is this heat normal? I have no hot water going into the unit, only cold water.
1 Answer Francisco, There is no way to bypass the controls and if this is a new unit would recommend having service out to check the unit to see what the issue with the unit would be. Read More...
Cain September 04, 2016 for Model Number PLD4555RFC3 My dishwasher control panel has become difficult to use and when I finally get it to light up with a wash cycle I want, it ends with 'washing drying ER clean S'. Based on other comments on your site (THANK YOU!!!) it looks like this is a control panel replacement part/issue. My question is: Are my dishes clean? They didn't seem to dry well but if 'clean S' is showing on the display... Did the wash cycle complete (and can I put my dishes away, CLEAN)?
1 Answer Cain, With a problem in the control panel/key pad assembly 5304504659 / 5304504659 there's no way to tell exactly. Basically, there are several key pad inputs at the same time. This "confuses" the control board and it produces the error code. There is no way to determine at which part of the cycle this occurred. It's best and safest to presume the dishes weren't washed or rinsed properly, and get a new control panel installed as soon as possible. In the mean time hand wash the dishes. Read More...
Jessica H August 28, 2016 for Model Number FGHD2465NFLA My dishwasher start button wouldn't work then the lights wouldnt come on. So I finally got it to start washing if I set it on a delay. Now it's reading Er clean S. It says fridgidaire outside and electrolux inside so I am also unsure of the part to search for. I'm assuming it's the control panel?
1 Answer Jessica, With the ER Clean S error this would be a faulty touch pad control panel. The control panel part number for your unit will be 807545704. Read More...
Albert B. August 23, 2016 for Model Number FGHD2465NW1A My dishwasher flooded around and under it. The timer stopped at about 35 minutes and kept running and running then water was on the floor. Does it sound like the control board is bad?
1 Answer Hello Albert, You should run the water/service test. To activate Water/Service Test, place unit in Power Failure or Idle Mode and the press”DRY or “AIR DRY”(model dependent) and the START/CANCEL keys for 3 seconds. The dishwasher will then step through the test cycle, if at any time, the START/CANCEL key is pressed, the current step is terminated, while the test sequence advances to The next cycle step. The unit should display a fault code as follows: PF - A power failure has occurred Hd or HO - Water heating delay CL - Close and latch the door ER/ER....Switch Failure ER/CE....Configuration Error ER/uo.....Vent will not close ER/uF.....Fan not running ‘01-24’ - Hour(s) delay before Start (some models) Read More...
Selena August 18, 2016 for Model Number FGHD2465NF1A Dishwasher Start button and drying selection buttons not working. If I put it on Delay, and circumvent the start button, the dishwasher seems to be fine. Do I need a new control panel? Is that the same component as the touch panel or do I need to purchase both?
Jay August 14, 2016 for Model Number PLD4050RHC1 Dishwasher threw an ER code. I disconnected power, reconnected it. ER code had disappeared, but now dishwasher display reads "91" and the China wash light remains on. I can push all other buttons to change the cycle setting, but within 2 seconds it defaults back to the China light. Tried to let it run in that cycle for a bit, but eventually it goes back to the Er light flashing, the drying, washing and Surge light flashing and an S flashing. Is this a touchpad problem that can be fixed with a new touchpad panel? Or a control panel? Or both?
1 Answer Jay, This issue would be caused by a stuck key on the keypad and would require a new control panel which is part number 154639211. Read More...