Ron March 01, 2019 I have a Frigidaire Gallery 24 dishwasher model #fghd2433kf0 When you choose your wash cycles, all come up with a time of 99+ except the quick wash, which comes up 50. On that cycle it counts down to 44 then kicks up to 99+. Do I need a new control board? Ron
2 Answers Ron, you may want to check the turbidity sensor located in the sump assembly under the filter screen. The turbidity sensor can have a build up on it that can cause the dishwasher to sense heavy water soil and cause it to have long wash times. Read More...
Darlene February 09, 2019 for Model Number FGHD2433KF1 My start stop light has never worked from the day we bought it. In order to fix this problem I need to purchase a control board. Is the correct? Thanks
1 Answer Darlene, the component responsible for the LED indicators would be the user interface panel [154791806]. If the user panel was not operating at all, then you would look towards the main control, but as it is the LED indicator, it would be the panel itself. Read More...
Rui Yi October 27, 2018 for Model Number FGHD2465NF1A it only show "washing drying , er s" on the the screen, I try press start/cancel, and drying for 3 seconds , but seems not working. should i change the control board? thanks
1 Answer Rui, For this issue the most likely cause will be a faulty user interface and will need the console 807545704. Read More...
Jim October 20, 2018 for Model Number FDB4315LFC0 I could set up the dishwasher to begin, pressing "normal wash", or any of the other cycles. When I push the "start/cancel" button, nothing would happen, and the unit would cycle off after a few seconds. I replaced the console assembly, but that didn't change the problem. Does this sounds like a control board issue? Thanks. Jim
1 Answer Jim, Based on the information you will want to first check the door switches to make sure that they are good and if they check ok then the control board would be the issue. Read More...
Shawn September 23, 2018 for Model Number FGHD2465NF code flashing Er clean S. your answer was a faulty control board. can I order a control board? Where?
1 Answer Shawn, This would be a control panel that is faulty and would be part number 807545704 and can be purchased at appliancepartspros.com or by calling 877-477-7278. The ER Clean S would indicate a stuck key on the keypad. Read More...
Kendra September 12, 2018 My Gallery dishwasher will not start. There is the PF code, nothing else works or lights. We have turned the power off and back on multiple times, left the power switch off for at least 30 mins, still nothing. Anything else I can try?
1 Answer Kendra, A model number of the dishwasher would be a big help, but, if you still have the PF code, first check for proper connections and power supply (120 VAC) at the junction box behind the lower access panel, on the front frame of the dishwasher. Remove the door panels and check the door switch circuits and wiring. If all's OK, replace the control panel / key pad assembly first. You probably have a problem in the circuitry, and the inputs from the keys aren't communicating with the control board. Read More...
John September 06, 2018 for Model Number PLD2850RDC2 When I start a wash cycle with my dishwasher the display normally shows a number, like 86 (indicating the length of cycle in minutes) the display counts down from 86 down to 0 when the cycle ends. Currently, when I start a cycle, the display shows 1. The dishwasher will run and the display counts upwards to 10 and then the dishwasher stops and the display clears. While running, the key pad does not respond to any commands (ie. Cancel). I’ve shut the power off at the breaker for extended periods, but it doesn’t fix the problem. Is this a touch pad, control board or control panel issue?
Chris Bridges July 22, 2018 for Model Number FGID2466QF3A Error code F not PF? Nothing online for F code?
1 Answer Chris, There would not be just an F code but could be a PF or a UF. Would try hitting cancel and see if the code disappears and if it does not then check the vent motor as it may be causing the issue. Read More...
1 Answer Thomas, normally a PF represents a power failure and can be cleared out by pressing the cancel button, if it continues, you may need to replace the main control, 5304514670 Read More...
Bob R. June 17, 2018 My dishwasher starts and during parts of the cycles will stop and display the pf code. Do you the board is going bad?
1 Answer Bob, We will need to have the model number of your unit to be able to assist with your question. Read More...