Juan March 27, 2011 for Model Number ftf2140es3 When my washing machine finishes all the lights start to blink and it starts to ring. After a short while, it turns off then it starts again and it will keep going until you dissconnect power. Also sometimes it skips the washing cycles.
1 Answer Hello Juan. First check the pump and make sure it is not clogged. If it is clear, you may have a bad control board. Hope this helps. Read More...
Tk March 25, 2011 for Model Number ftf2140es0 Now that I replaced both control boards, ensured the drainpump is pumping and no clogs> the door is locking. and my washer still will not go into is high speed spin can you give me any other suggestions. and it still gives me code 43.
1 Answer Hello TK. Did you replace the door lock, or just see that it is locking? These can lock and still be bad. They have to make up for the spin to work properly. It sounds like the lock may be the problem. 131763256 Hope this helps. Read More...
Tk March 13, 2011 for Model Number FTF2140ES0 Now that I have replaced the control board and still no final spin. Where to I go now? It is still giving me error code 43?
1 Answer Hello TK. Check the motor control board 134743500 and make sure all connections are good and tight. If so, then the motor controller could be the problem. Hope this helps. Read More...
Michelle March 10, 2011 for Model Number LTF2140FSO My washer will not do the final spin cycle. It washes fine in all cycles and pumps the water out but just doesn't spin them out. What do you think the problem might be?
1 Answer Hello Michelle. Check and make sure the door is locking. If so, you may be dealing with a bad control board. Hope this helps. Read More...
Tk March 09, 2011 I have a fridigaire front load washer model #FTF2140ES0. It appears to run thru all cycles with the exception of the spin cycles. I ran the self test and spins and drains properly. I also was able to run the self diagnostic and it give me error code 43 (control board problem> I am looking for confirmation that this is my problem. also what is the dificulty level to replace control board. I am pretty handy with tools but hardly dabble in appliance repair. Thanks, TK
1 Answer Hello TK. That is correct. According to the code, you will need to replace the control board. These are not hard to do. Just remove the top assembly, and remove the control panel. Hope this helps. Read More...
Ron March 08, 2011 I have a washer md#LTF2140FSO. When I start the cycle it starts, then stops, within two seconds. I cancel then try again, it starts to run water, then it stops. When I put the drain cylce it start to drain then stops. Is my control board bad?
1 Answer Hello Ron. Check and see if the door lock is locking on the machine. You could have a bad door lock assembly causing this problem. Here is the part number for the lock assembly. 131763256 Hope this helps. Read More...
My07bobber March 07, 2011 Like the previous questions, My Fridgidaire front loader will not work on normal either. All other cycles work when selected. I'm assuming contol board as well. Mine is the GLTF2940ES3. Is this the same control board pictured or is it another ?
1 Answer Hello. Your board number according to your model number is 137006000. Hope this helps. Read More...
Joe March 03, 2011 I have the same problem where the other cycles work fine however when turned to normal the 8 hour delay light comes on and it won't start . If the pump is clogged would that not affect the other cycles ?
1 Answer Hello Joe, Yes the pump would affect the other cycles. Is sounds like you have a bad control board 137005000NH. Hope this helps. Read More...
Steve February 27, 2011 If the normal cycle on my Frigidaire front load washer model FTFB400GS0 will not run does it point to the control board as the problem.