Mike September 26, 2014 for Model Number ATFB6700FS0 My washer starts then goes approx 10-12 min into cycle then goes into a pause mode then shuts off. I have to open & close door and repress the start button then it will finish entire wash.
1 Answer Hello Mike, Quick Check If there is no error displayed and the washer momentarily starts then turns back off: 1. Listen for a relay closure inside the motor control shortly after the Start/Pause key is pressed. If this happens, the motor control has power. 2. Check the 5 pin connector wiring between the console control and the motor control. The tech sheet should aid greatly in the diagnosis of this issue. It will be in an envelope by the motor speed control board in the base of the machine. Without doing anything I would suspect the door switch or a poor electrical connection as the culprit as long as the motor is turning the spin basket during agitation. Read More...
Barb September 05, 2014 for Model Number Frigidaire LTF2940ESO frigidaire ltf2940eso When a cycle is selected the time displays then switches to LOC and continues to go between the two displays. Nothing will start. How can I clear the panel to tackle the real problem. Unplugging it didn't help. The original problem was the Drain/Spin Cycle. It sat with no motion from 13 to 10 minutes then go into a slow spin until 7 minutes, then shut off leaving soaking wet clothes. Please help. Thanks
1 Answer Barb, With the unit display showing the time then switching to LOC would be an issue with the control board. The LOC is an indication that the control panel is locked so you will want to make sure that it is indeed not locked and if not then replace the control board 134743500. Read More...
Stacey September 03, 2014 My front end loader Frigidaire Affinity washer gives me a code E91. I cannot do anything to stop it. It beeps every 40 seconds or so, but I cannot change the dial or anything. Suggestions?
1 Answer Hello Stacey. Communication error between UI board and control board. Check wiring and replace the board if the wiring is good. Read More...
Mark T August 27, 2014 for Model Number Frigid are gltf2940fs1 Washer gets 4 minutes into cycle then stops. During the time it is operating, tub agitation is intermittent not constant. I replaced the drain pump because tub was not draining. Error code is E21. Is this control board failure?
1 Answer Hello Mark. Did you check the filter 137518800 when you replaced the pump? If not, it could be clogged and causing the issue with the unit. If everything is clear inside the unit, it could be the pressure switch or the pressure hose causing the issue and providing a false reading to the control board. Read More...
Joe August 27, 2014 for Model Number LFAW7000LW0 I have a fridgedaire frontload washer and it hasnt worked since a lightning strike on house about 2 weeks ago, the display screen is blank and it wont run at all . I looked at wiring, main board/control board/display board and cant see anything burnt up. Is there any way to check main board?, how can I diagnose this? Anything would help
1 Answer Hello Joe. The best way to test is using a meter and testing for power to the control board. If there is power there, the board is bad. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Israel August 24, 2014 for Model Number LAFW3511KW0 My Frigidaire Affinity washer gives me a code of E90. I was wondering if I have to replace the control board. I'm not sure what part to replace?
1 Answer Hello Israel, This is going to be a poor electrical connection, usually on the main board. This is not repairable so the main board 137006060 will require replacement. Read More...
Tom August 22, 2014 for Model Number ATF7000ES1 Recently had a flood with about 5 inches of water. I have a Frigidaire affinity front loader that turns on and everything works but will not spin at all. When set to 12 min spin only setting. The pump turns on runs a few seconds then turns off time goes down but will not spin . Fault code E5E. Is the speed control board probably bad since it was under water?
1 Answer Tom, Yes, the motor control board 134743500 is most likely at fault. The E5E error code indicates a communication error between the motor control and control panel. If there were 5 inches of water inside the machine, you can pretty much figure the control is defective. Read More...
Robert August 13, 2014 for Model Number ATF7000ES1 Started washer. It filled with water then stopped. Tried to re start, all lights would come on then the door lock light would go off and nothing. Have an error code of E68. Friend said it is the speed control board?
1 Answer Hello Robert. This E68 is a stuck keypad. You will need to replace the board on the unit if you do not find any stuck buttons. Read More...
Shane August 07, 2014 for Model Number atf6000fs Displays error code E41. Voltage on J2 reads 120V. Manual says that is control board problem. That means the motor control board in the back of the unit correct? not the front control board with all the leds? Also wondered if there were common fixes for the control board that I could do myself as far as soldering in new components.
1 Answer Shane, The manual states that the control is not reading the door lock being closed for the E41 error. If you determined that the control board is faulty then the issue will be the user interface control board and not the motor control board. Read More...
Jay July 30, 2014 for Model Number ATF6000FS2 I have frigidaire washer that lights up when I pick a setting, the door locks and 5 seconds later turns off. Does that sound like the control board? It's only 4 years old. Thanks
1 Answer Hello Jay. If the unit runs for 5 minutes and then shuts down, it does sound like the control board has failed in the unit. Read More...