Kevin R July 10, 2022 for Model Number WPRB8050D1WW. General Electric I need to change both of the suspension rods in this Laundry washing machine. What are the part numbers to order? Thank you.
1 Answer Kevin, Thanks for the question, the suspension rods are parts numbers WH16X10057 and WH16X543 You will need two each of these. Read More...
Bryan January 29, 2022 for Model Number GTW490ACJ1WS Can you tell me how many rod and spring assemblys are needed for a GE deep fill washer. Also the original part number I guess isn't made anymore so this is the new part number I think, can you confirm that? Original part numbers: WH16X26910 and WH16X26911 New part numbers: AP6286937 and AP6287023 The reason for replacing them is because it shakes way more than before. Thanks for your help, Bryan
1 Answer Bryan, this model will use two white suspension rods WH16X26911 and two green suspension rods WH16X26910. Read More...
Paul July 18, 2021 for Model Number gtw680rsj3ws My issue is that on every cycle that I choose, after the cycle has ended, before it shuts off the balance error shows up and it goes through a 12 minute cycle to balance the washer out. It give this balancing error EVEN though the washer is not out of balance. Not sure what the problem truly is? how many suspension rods does this model have, If 4 then how to find out which one is bad without checking all of them. .
1 Answer Paul, If you are replacing one suspension rod it is best to replace all of them at the same time. There are 2 for the left part number WH16X26911 and 2 right WH16X26910. Read More...
Timothy February 07, 2021 for Model Number WHDSR109J5WW Im needing suspension rods for my washing machine. The manual you have shows two different rods, but the quantity of each is not listed. Can you help me out?
1 Answer Timothy, this model will use two rear suspension rods WH16X544 and two front suspension rods WH16X543. Read More...
Travis Jones July 22, 2020 for Model Number GTW220ACK1WW Need the spring it shows two different ones.
1 Answer Travis, You would need to get 2 of part number WH16X26909 and 2 of [WH16X26908]. Read More...
Renee March 09, 2020 for Model Number HSWP1000M4WW My washer started making a horrible noise. took the front panel off and there were metal shavings at the bottom like the metal part below the motor was dragging on the bottom of the washer. What in the world could be wrong.. HELP
1 Answer Hello Renee, the tub suspension rods need to be relaced, rod WH16X10159 is used in the rear position and the other 3 positions use rod WH16X10158. Read More...
Tairla July 07, 2019 for Model Number VC GE I have read all the questions here and they all say to replace the rods. What if they have been replaced and it still makes grinding noise? I have had the maintenance guy here 4 times and it still grinds. They sprayed some WD 40 stuff on the joints but it keeps coming back.
1 Answer Tairla, We will need your model number to help you find the right parts for your unit. Please post another question with all your info included thank you. Read More...
Mary March 17, 2019 for Model Number Gtw330aksww I have a ge 330 model and during a move , I noticed that a plastic cover from under drum was on the floor, it was part of the suso, can I still use the washer?
1 Answer Mary, you may find the washer shakes more than it did prior to moving it. When you have the washer in the proper position, make sure it is level and does not teeter. If it has a locking nut on the leg, make sure it is tightened and locked into position. Read More...
Paul February 23, 2019 for Model Number WJRE5550H1WW The tub is sagging enough to hit bottom when partially full. We installed new spring rods but it still bottoms out. The Aprons around the top look very weak, so I suspect they just bend? Is there a fix? Thanks.
1 Answer Paul, For this issue the apron conversion kit WH49X20925 would be what is needed. Read More...
Sally November 14, 2018 for Model Number GTWN4250D2WS When replacing suspension rods on a washer, do all four rods need to be replaced at once? If not, how can I tell which ones need replacing?
1 Answer Sally, If replacing a suspension rod because of visual or bent damage then one will be ok. If you suspect an out of balance because of the springs you should replace as a set. Read More...