Larry C. August 12, 2012 for Model Number Kbfa20erss01 My ice maker was over flowing and causing the tray to beco,e one block of ice, this happen about five times Then stop flowing water completely. Is it my ice maker that went bad or something else. I Los headwater lime to get drinks from and that works fine help!
1 Answer Larry, You're on track. The place to start is the water inlet valve WP67005154. also check and replace the water filter, if you haven't done so recently EDR4RXD1. Make sure you "flush" the water supply line, before to attach it to the new valve assembly. Thanks Read More...
Casey June 10, 2012 for Model Number msd2655hew Do you have just the o-ring seals for the water valve?
1 Answer Hello Casey, The water valve is not serviceable as per the manufacturer. Since it is "melted" together in the manufacturing process, if it is opened, it is destroyed. Read More...
Brett May 26, 2012 for Model Number KBFA25ERBL01 I need to order a new water inlet valve and all the external tubing, (and track) but can't remember what it all looks like & how it goes back together- I removed it all and threw it away after a rat chewed up all the tubing, the track and the water inlet valve. We've been using it for a few years w/o water but I want to fix it. I need P/Ns, and a suitable diagram. Thanks very much! Brett
1 Answer Brett, Most of those water associated parts are pre-assembled and you'll have to order "complete parts : WP67004106, W11361728,WP67005154, W10823511 . As for routing and installation, we're sending you some more information. Good Luck and Thanks Read More...
Richard May 09, 2012 for Model Number mzd2665hes Where the water comes out to fill a glass, after you filled the glass it keeps dripping water.
1 Answer Hello Richard. If the dispenser keeps dripping water and does not shut off, you will need to replace the water valve WP67005154 in the unit. It sounds like it has a slow leak. Read More...
Jsettles April 24, 2012 for Model Number Msd2651HEW Installed new valve-inlet and still makes rattle noise but no water or ice??
1 Answer Hello Jsettles. Based on the information you provided, if the noise is coming from the filter head location, you will need to replace the filter head WP67006524 if the first 2 numbers of the serial number are 50 or later and WP67004106 is it is 49 or before. Read More...
Warren March 25, 2012 for Model Number psd262lhe I am replacing a water valve. How do the lines come out of the old valve?
1 Answer Hello Warren, This is called a John Guess fitting. To install a line you push the line in and after it bottoms, it will pop in about another 1/4 inch. To seal it, you simply pull on the line. To remove it you push the line toward the valve and while still pushing, push in on the ring around the line. While holding the ring in, pull the line out. Read More...
Anthony February 15, 2012 for Model Number KBFA20ER I just replaced water inlet valve to correct ice maker water drip into ice cube collecting try. It's still dripping. Any suggestions ?
1 Answer Hello Anthony. You will need to run about 2 gallons of water through the dispenser to remove any air in the system and stop the dispenser from dripping. If the problem continues after this, you will need to check and see if it is getting air in the lines from a small crack or bad filter. If all is good, you may need to replace the icemaker D7824706Q. Hope this helps. Read More...
Anthony February 15, 2012 for Model Number KBFA20ER The yellow and brown double prong plugs at the valve. Does it matter if they are mistakenly re-installed upside down ?
1 Answer Hello Anthony. No, the wires will still work properly on the water valve WP67005154. Hope this helps. Read More...
Lipton Tea Bags January 23, 2012 for Model Number ASD2620HRB This fridge was donated to us. The water valve was missing and the 3 lines were cut. I ordered a new valve and need to know where the two gray 5/16" lines go coming from the upper left of the back (one has 2 blue bands on the end) and then the one 1/4" clear line coming from the upper right. I also noticed two clear 5/16" shorter lines behind where the valve goes. The left line goes up to the fridge and the other end thru the back. The other line comes down from the fridge and the other end is open into a drip pan.
1 Answer Hello. The grey line with the brass fitting coming from the filter head WP67004106 is for the water supply line of the house. The other grey line with the blue strips goes to the single top hole on the water valve WP67005154. Then the other two water lines are sized different for the valve. One is ¼" and the other is 5/16". Hope this helps. Read More...
Ron January 14, 2012 for Model Number MSD2651HEW I just need the blue keeper insert that holds the water tube into Water Inlet Valve (AP4080917). Do I have to by the entire valve or can I just by the clip? Home Depot and Lowes sell 1/4" & 3/8" but this looks to be a 5/16".
1 Answer Hello Ron! The entire valve must be ordered, parts are not available separate. We will need your appliance serial number to verify the correct valve on your product. Thanks. Read More...