Jay August 06, 2017 for Model Number WTW7340xw0 Does part #W10445302 bearing kit fit my whirlpool cabrio WTW7340xw0?
1 Answer Hello Jay. Yes, You need to order part numbers W10435302 and W10447783 to repair the unit. Read More...
1 Answer Hello Michael! Unfortunately the manufacturer does not offer the compatible bearings separate from the tub assembly part number W10772617. Thanks! Read More...
John July 10, 2017 for Model Number Cabrio WTW6600SW2 I installed the kit per instructions, but the drive shaft would not fit properly in the top bearing. It was way too tight. After pounding out both bearings the top bearing fit nicely on the shaft. Why was it too tight once installing in the machine, but fine when not installed? I noticed when pressing in the bearings that the "arm" of the installation tool didn't touch the bottom of the sump. There was a small space. Did the top bearing get pressed in crooked? It seemed fine. I presume the new bearings are ruined by pounding out of the machine. Thanks
1 Answer Hello John, If the bearings were not properly installed, they can be damaged during installation. The manufacturer recommends replacing the outer tub assembly which includes the bearing and shaft assembly pre-installed into the tub by the factory to avoid this issue. It is also possible that there was an issue with the new parts prior to their installation. It is not recommended to re-install the parts one driven back out. We would recommend calling us at 1-877-477-7278 and have the parts replaced under the part warranty. Thank you for your patience and understanding in this matter. Read More...
Tb July 06, 2017 for Model Number WTW7340XW2 Let's start with, I am an idiot. Now that is out of the way. I am almost completely installed and realized i missed a very important detail in the video, I left out to spacer tube and washer. What will happen if not installed? Do I need to pull it all apart and drop out the lower bairings and install?
1 Answer Hello TB. You will need to take it apart and install those. Otherwise, the slack will cause the bearings fail on the unit. Read More...
Bobby June 25, 2017 for Model Number Kenmore Model # 110.28032701 Will this Washer Tub Bearing W10435302 with Bearing Installation Tool Part Number: AP5325072 work for the Kenmore model 110.28032701?
1 Answer Hello Bobby, I'm sorry but the part you were viewing does not come up as a valid part for the model provided. You will need to order W10193886 as per the manufacturers' recommendations. Read More...
Kailan June 09, 2017 for Model Number WTW8800YC0 Is part number W10435302 (bearing) compatible with my washing machine? Model number WTW8800YC0
1 Answer Kailan, Yes, the W10435302 / W10435302 Bearing and Tub Seal Kit is compatible to the model number you supplied. Don't forget to order the Installation tool W10447783 to properly remove and install the components into the tub. Both parts are in stock and available at this time. Thanks, Read More...
Cary May 30, 2017 for Model Number WTW6700TW1 I have 2 questions. Question # 1: I pulled the inner tub out to replace the drive shaft, bearings and seal. The inner tub sounds as though it has fluid inside of it. I turned it upside down, laid it on its side and cannot get any of the fluid out. Do I not worry about it? Do I drill a hole and try to drain it then plug the hole? What do you think? Question # 2:When I removed the basket hub and the cogged hub, there were (2) metal pieces under it. One is a flat thin washer and one looks like a metal gasket. I do not find the items in the parts listing.
1 Answer Hello Cary. No, you do not remove that liquid. That is the balance system of the washer. As for the metal shims. I do not see them listed as an available part on the diagram. If they are needed, you will need to use the old ones. May not be needed with the new bearing kit. Read More...
1 Answer Hello Rob, The bearing kit is W10435302 and the tool for its' installation is W10447783. I'm sorry but we do not have rental information available on the tool. Thank you for your patience and understanding in this matter. Read More...
1 Answer Hello Pat. Sure, you can get that error with bad bearings. If it causes the tub to be binding up. Read More...
1 Answer Hello Pat. F then 54 flashes when the machine/motor control detects high current for the motor module. ? Does basket turn freely? If not, determine cause of friction. Read More...