Chuck February 14, 2013 for Model Number mer6769baw Hi Just wanted to make sure I am getting the right part. Need the small front burner for the Maytag Gemini. Thanks
Stephen L. February 07, 2013 for Model Number 8770RV I have the Maytag Magic Check electric cook top (Model # 8770 RV) and the glass has broken. I found that you no longer carry the glass top itself and was curious if this glass can be purchased from a glass supplier or if you are aware of another supplier. Can you please assist?
1 Answer Hello Stephen. The glass top has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part. Read More...
Toni January 27, 2013 for Model Number MER6772BAB I need to replace the right front big burner on my maytag gemini ceramic top stove. It has the switch where you can make it a small burner or use it for the larger burner. Can you tell me what the parts number is for this element? Thank You.
Jason December 27, 2012 Replaced 6" element on Crosley glasstop stove. Now when I turn it on it acts like its on high setting even if on low. All other burners are normal.
1 Answer Hello Jason, It sounds like either the limiter is bad on the element or wired incorrectly. We could assist better with a model number for the unit. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Sheryl November 25, 2012 for Model Number MER6772BAW I need to replace the large, left front burner on my ceramic top stove. What part number would that be?
Michael L November 20, 2012 for Model Number jer8850aab I ordered a 6" element for my Jenn Air electric range. The instructions that came with it say to compare my old element limiter with the new one, and change the position of the wires on the terminals based on the new diagram, as the terminals ie. 1A, 1B, 2A, 2B are in different locations. Acutually 1A is a fixed jumper, so that location did not change. I spliced in the extra lenghts of wires that came with the kit, and installed the terminals per the new diagram. When I turned on my knob switch, the light came on but the element does not heat up at all. Any suggestions?
1 Answer Michael, You may have wired the element assembly wrong. Regardless of the instruction sheet, you need to verify the terminal locations on the new element limiter as compared to the original. and attach the corresponding wire to the corresponding terminal, ie, the 1B terminal should have the red wire, common to all the 1B terminls on all the elements, 2B should have the yellow wire that attaches to the hot surface indicator light. The 1A terminal has the metal jumper, and the 2A terminal should have the yellow wire from the H1 terminal of the infinite switch attached to it,the remaining yellow wire from the H2 terminal of the infinite switch will attach to the terminal on the side of the element housing. If you check and you're sure the replacement element is wired in this configuration, then you'll need to check for 220-240 VAC across the yellow wires (side of element and 2B) with the switch on, to determine if the infinite switch is at fault. Read More...
Bob November 12, 2012 for Model Number mer5730 aaw 6 in element shown in picture has a different connection. Mine has 4 legs and 2 legs, picture shows 2 legs connected together. Maytag mer5730AAW serial # 1449.Mfg. Part # is 74002653 how do you connect the wires ?
1 Answer Hi. The element part # W10823704. The double red wires connect to the element 1b terminal. One of them comes from the 1b terminal on the left front elemt. and the other one is from the 1b terminal of the rt rear element. The red wire from the hot surface indicator lights connect to the element 2b terminal. From the 12 pin disconnect plug on the surface burner wiring harness the # 1 wire connects to the element terminal. The # 3 red wire both connect to the sensor left open on the side of the element sensor "block". Thank You. Read More...
Ariel July 04, 2012 for Model Number cer3760aaa Which is the correct element for magic chef Serial # 173327759WW?
1 Answer Ariel, according to your model/serial combo the replacement 6" element is part number W10823704 and the 8" element is part number W10823707. Thanks! Read More...
Bruce S. April 25, 2012 for Model Number MER6750AAW The oven door is stuck in the lock position. Have tried disconnecting power and starting the clean cycle etc. and it will not unlock. How do I raise the cook top to replace the latch when the door is locked shut?
1 Answer Hello Bruce. Use an ice pick and reach inside the oven door vents WP74003653 and pull the lock WP74005575 over so you can open the door on the unit. Read More...
Roger February 25, 2012 for Model Number MES5770AAB ser 26151147AR Which 6" Burner AP4008687 or AP4012913
1 Answer Roger, the correct 6" element for your range, based on the model and serial number you supplied is W10823704. Your guess was pretty accurate. Thanks and Good Luck Read More...