Ellen July 23, 2023 for Model Number JFC 2089HEP Hi, Water dispenser still not working after replacing every part possible. Ice Maker was also replaced and that's fine. I get one short burst of water out of the dispenser then it stops. I did replace the Water Inlet Valve already but perhaps it is a bad valve again. When checking across the connectors of each valve what should the ohms reading be? I get 246 ohms and 191 ohms. I am thinking the valve is faulty. Thoughts? How to Replace Dual Water Inlet Valve WP67006531 / AP6010515 #WP67006531
1 Answer Ellen, Check the water valve for proper voltage when the dispenser is pressed. If you have power to the valve and it does not open the valve is bad. Read More...
Donny June 15, 2022 for Model Number MCD2257KES I am getting large blocks of ice in the ice cube bin. They block the ice maker dispenser outlet. What is leaking after ice maker dispenses water to refill?
1 Answer Hello Donny, check the ice maker fill tube is in place, check the ice maker's fill cup is not out of place or cracked, if both ok likely it is a faulty water valve allowing too much water into the ice maker WP67006531. Read More...
Rob February 22, 2022 for Model Number MSD2641KEW I am not getting water to the icemaker. I am getting water at the dispenser at the door. Could my problem in the water valve?
1 Answer Rob, the inlet tube going to the ice maker fill cup will need to be inspected for an ice blockage. If there is an ice blockage, the ice would need to be cleared and the valve WP67006531 would need to be replaced. If there is not an ice blockage, the ice maker would need tobe tested for 120VAC from terminal N to terminal V during a harvest cycle. If there is not voltage at the end of the harvest, the ice maker D7824706Q has failed. If there is, the valve has failed. Read More...
Brandon September 22, 2021 for Model Number MFC2061KES The ice maker was not working so I replaced the unit in the freezer. And I still don’t have ice. Any chance you guys have any ideas?
1 Answer Brandon, Check the temperature in the freezer at the ice maker to be sure it is below 8°F. Then check the fill tube to make sure it is not frozen up. Then check the fill valve for the ice maker to see that it is working. Read More...
Cal May 16, 2020 for Model Number MSD2652KES Infrequently when we try to dispense water, there is a vibrating noise and the water rate slows to a trickle. I can't determine where to noise is coming from. I've watched your videos to replace the dual water valve, water filter head and the micro switch behind the water/ice dispenser. We have run a lot of water through the dispenser so I don't think its air. Haven't seen any water leaks. Have also disconnected the filter and reattached several times. There is a pinhole stream of water coming from the filter head when the filter is removed. The filter is fairly new. Could it just be a bad filter? What parts should I replace first?
1 Answer Cal, Based on your post information and description you should consider the WP67006524 / 67006524 Water Filter Head and Tube Assembly. If the bypass "fingers" are distorted or bent, etc. there can be a vibration inside the mechanism, and if the water is leaking from the filter head " There is a pinhole stream of water coming from the filter head when the filter is removed." there is a failure in the filter head. Read More...
Byers, R.E. April 11, 2020 for Model Number KBFS25EVMS00 Icemaker does not work - Found ice blockage at rear of ice maker inside of fridge - Used wife's hair dryer to melt ice - Unit then produced 3 trays of ice, but froze up again - do I replace dual water valve or the entire ice maker ? Suspect water is getting by shut off valve after it cuts off. Thank You, Bob Byers
1 Answer Bob, it sounds like your inlet valve is letting water seep into the icemaker, therefore causing an ice blockage, you can replace the ice maker inlet valve, part number WP67006531 and it should take care of the problem. Read More...
Ron February 09, 2020 for Model Number Maytag water valve # 12544118 Need push to connect fitting. Its blue 5/16 tubing.Has P3 stamp
Bubba September 06, 2019 for Model Number MSD2641KEW Water is leaking from our water/ice dispenser. We replaced the filter recently and it made it worse. Could this possibly be the inlet valve has gone bad?
1 Answer Hello Bubba, This can only be caused by air in the system, a pinhole in a water line, or a failing water valve WP67006531. Read More...
Vbch September 14, 2018 for Model Number KBF S25EVMS00 I replaced the dual water inlet valve on this refrigerator two years ago (almost to the date). How long are these inlet valves supposed to work before failure? I'm having issues dispensing water again; I can hear the pump kick on but no water is coming out. I removed the filter, installed the bypass cap and still nothing. The tank is not frozen, I think it's the valve but shouldn't the replacement part last longer than two years?
1 Answer Hello VBCH, The life of the water valve is dependent on the mineral deposits and sedimentation of the water supply and also the fact that the part is manmade has to be considered since man is not a perfect creature, (man cannot make a perfect part). This sounds like the water valve WP67006531 has failed again if no tubes or the water tank are frozen. Read More...
Norris H August 17, 2017 for Model Number GI5SVAXVLOO whirpool I recently replaced the dual water valve, and when I re-connected the piping, it would not fit properly. If I re mount the valve, it is under a strain and the discharge fittings drip. Can I re-shape this hard plastic piping hsing a heat gun or hair dryer to relieve the strain? Also, this valve and the previous one, it was very difficult to remove the piping. The collars on the valve are almost flush with the valve and won't move to release the piping. Thanks.
1 Answer Norris, When removing the tubing you push in on the collar and then pull out as you are pushing. When reinstalling the tubing you have to make sure that you push the tubing in all the way. It will get to a stopping point where you think it is all the way in but may have to push a little harder to get it to fully seat. You do not want to reshape the part and you want to make sure that you have a straight cut off. Read More...