Parts for Frigidaire LRA187MT210: 03 - Recommended Spare Parts

This replacement air filter screens airborne particles before they enter the appliance. Installing a clean, intact filter helps maintain proper airflow and protect internal components so the unit can operate as designed. What it does:

• Traps dust and lint before they reach the fan and internal parts
• Helps maintain smooth, unobstructed airflow
• A clogged or torn filter can cause weak airflow or unusual noise
• Replace when the filter is missing, damaged, or will not stay seated

• 1 air filter

• Disconnect power before servicing
• Open the filter access or grille and remove the old filter
• Insert the new filter in the same orientation; ensure tabs/slots fully engage
• Do not operate the appliance without a filter installed

Color: gray. Measures about 2 inches wide by 3-1/2 inches deep.

This oven temperature sensor detects the internal temperature and sends readings to the range control so the oven can maintain accurate cooking temperatures. Replaces a failed or intermittent sensor to restore reliable temperature control. What it does:

• Senses oven cavity temperature and provides temperature data to the control board
• Helps the control maintain set bake/roast temperatures
• Common symptom: oven temperature is incorrect or fluctuates during cooking
• Common symptom: cook cycles take too long or oven does not reach set temperature
• Common symptom: oven displays a temperature sensor or sensor fault code

• One oven temperature sensor (1 each)

• Disconnect electrical power to the appliance before removing or installing the sensor
• Handle the sensor carefully to avoid damaging the probe or wiring and ensure proper connector seating
• Inspect wiring and connector for damage; replace if frayed or corroded

This electronic control board is the appliance's main PCB that manages functions and the user interface. Replacing a failed board can restore normal operation when the unit is unresponsive, erratic, or displaying control-related errors.

• Directs operation of key components based on user settings and sensor feedback
• Powers and communicates with the display/interface and control pads
• Coordinates timing through relays and interfaces with safety/protection circuits
• Common symptoms: no response to buttons, dead/blank display, unexpected cycling or beeping, control error codes, or visible damage on the old board

• Disconnect power before servicing and verify no voltage is present
• Use ESD precautions; handle the PCB by the edges and avoid flexing it
• Photograph/label connectors; transfer each to the same location on the new board, matching any jumpers or DIP-switch settings if present
• After installation, restore power and run the model's test/diagnostic or a cycle to confirm proper operation

This replacement capacitor stores and releases electrical energy to support proper operation of the appliance's circuit. Replacing a weakened or failed capacitor restores reliable startup and smooth performance in the affected component.

• Stores electrical energy and delivers a brief boost during startup as designed by the circuit
• Helps stabilize operation, reducing humming, stalling, or overheating from a weak capacitor
• Common signs include motors that hum but won't start, intermittent operation, breaker trips
• Visual clues of failure: swollen case, leaking oil, or burnt odor

• Disconnect power and verify no voltage is present before servicing
• Properly discharge the old capacitor using safe, approved procedures
• Note wire positions or take a photo; transfer leads to the matching terminals securely
• Mount securely in the existing bracket/strap; keep terminals clear of contact and test operation

This dryer lint filter captures lint and debris from the dryer's airflow to help maintain efficient drying and reduce lint buildup. Easy to remove and clean for routine maintenance and safer operation. What it does:

• Traps lint and fibers before they enter the exhaust system
• Helps maintain proper airflow for more consistent drying performance
• Reduces the chance of lint buildup that can cause longer dry times or overheating
• Makes routine maintenance simple — clean the screen after each load

• Remove power to the dryer before servicing; allow the dryer to cool
• Slide or snap the filter into the filter housing according to factory orientation
• Clean lint from the screen regularly with a soft brush or by rinsing and fully drying before reinstalling
• Refer to your dryer's user manual for any model-specific instructions or precautions

This blower wheel moves air through the dryer cabinet so clothes dry efficiently and the appliance vents properly. Replacing a worn or damaged wheel restores airflow and helps prevent overheating and long dry times. What it does:

• Spins on the blower motor shaft to draw air across the heating element and through the drum
• Restores proper airflow when a chipped or bent wheel causes reduced drying performance
• Reduces rattling or vibration caused by imbalanced or cracked fins
• Helps prevent overheating and extended cycle times due to restricted airflow

• One blower wheel

• Disconnect power (and gas if applicable) before servicing to avoid electric shock or injury
• May require removal of the dryer front or blower housing and loosening the motor to slide the wheel onto the shaft
• Ensure the wheel is oriented and seated correctly on the motor shaft and that set screws or clips are tightened as required
• Inspect motor shaft and housing for debris; spin the new wheel by hand to ensure free rotation before reassembly

This replacement blade fan moves cold air across the evaporator to help maintain even temperatures inside the compartment. It restores proper airflow for more consistent cooling and helps reduce frost buildup when working with a good motor. What it does:

• Circulates air across the evaporator to distribute cold air through the compartment
• Restores airflow when a cracked, warped, or missing blade reduces cooling efficiency
• Helps reduce uneven temperatures and localized warm spots caused by poor airflow
• Can reduce abnormal noises caused by damaged or unbalanced blades

• One replacement blade fan

• Disconnect power to the appliance before starting any repair
• Remove the evaporator cover/panel to access the fan assembly per your model's service instructions
• Handle the replacement blade carefully to avoid bending the blades or contaminating the evaporator
• If the fan motor or mounting hardware is damaged, replace those parts as well for reliable operation

This screw kit is a replacement hardware pack used to restore secure fastening of appliance panels and components. It provides the standard mounting screws needed when original fasteners are missing, damaged, or worn. What it does:

• Replaces missing or stripped screws that hold panels, trim, or small assemblies in place
• Restores secure fit to reduce rattling, vibration, or loose parts
• Helps correct minor alignment issues caused by lost fasteners
• Useful when preparing for panel removal/reinstallation during service

• Disconnect power to the appliance before servicing.
• Use the correct screwdriver or driver bit to avoid stripping screw heads.
• Tighten screws until snug; avoid overtightening to prevent damage.
• Follow OEM service instructions.