Parts for Lg LFXS28566S/00: Refrigerator Parts

Replacement mounting screw for refrigerator assembly. Secures components and panels inside your fridge. Order a new screw if yours is stripped or missing.

Replacement mounting screw for refrigerator panels, brackets, and internal assemblies. Restores secure fastening when original screw is missing, stripped, or damaged.

Replacement mounting stud for refrigerator door handles. Installs inside the door to secure handle assembly. Needed when stud is damaged or missing.

Replacement mounting screw for refrigerator panels, brackets, and assemblies. Needed when original fastener is stripped, worn, or missing.

Secures panels, brackets, and assemblies inside your refrigerator. Replace when original screws are missing, stripped, or damaged to restore proper fit.

Replacement freezer door handle for bottom-mount refrigerators. Installs on the freezer compartment door. Order if your handle is cracked or broken.

This rear door handle replaces a worn or damaged handle on compatible LG appliances, restoring a secure grip and smooth opening. It's a direct-fit exterior handle that keeps the appliance door operating and looking right. What it does

• Provides a secure gripping point to open and close the appliance door
• Replaces cracked, loose, or broken rear handle hardware
• Restores correct alignment and feel when the door is operated
• Helps prevent further damage to the door edge from makeshift handles

• Power off and unplug the appliance before starting work; remove food or shelves as needed for access
• Keep fasteners and mounting clips; transfer original hardware unless new hardware is explicitly included
• Test door operation and alignment after installation; tighten fasteners evenly to avoid stress

Ice or water dispenser leaking or dripping inside your fridge? This dispenser funnel assembly channels water and ice properly, stopping leaks and drips.

Plastic drain tube that channels defrost water from evaporator coils to drain pan. Replace if cracked, melted, broken, or causing water leaks in freezer.

Adjustable leveling leg that threads into the refrigerator base frame to support and stabilize the unit. Replace worn, broken, or missing legs.

Insulation duct for bottom-mount refrigerators. Installs inside the unit to help maintain temperature efficiency. Replace if cracked, torn, or missing.

Freezer drawer roller assembly enables smooth gliding of your refrigerator's lower drawer. Replace if drawer sticks, wobbles, or is hard to open. Confirm fit with your model number before ordering.

Dual roller wheel assembly that mounts to the rear wall of the freezer drawer. Replace when wheels are missing, broken, or cracked for smooth sliding.

Replace a cracked, broken, or worn refrigerator drawer tray assembly. Restores stable storage in your drawer compartment and keeps food contained.

Replaces cracked, damaged, or missing glass shelf in the fresh food compartment. Restores stable storage space for food and containers inside your fridge.

Glass shelf assembly with frame for bottom-mount refrigerator fresh food compartment. Replace cracked, broken, or missing shelves to restore storage.

Replaces the rear outer panel on your refrigerator. Restores finished appearance and protects internal components. Order a new cover if yours is cracked or missing.

Replace a cracked, broken, or missing refrigerator shelf assembly. Restores storage space with a stable surface for food and containers.

Replacement fresh room tray assembly for your refrigerator. Installs at the bottom of the fresh room drawer to contain spills and support produce storage.

Drawer slide rail guide assembly for refrigerator shelves and bins. Replaces worn, broken, or damaged rails that cause sticking or misalignment.

Air duct connector for refrigerators. Channels airflow between compartments. Replace if cracked, broken, or missing to restore proper air circulation.

Protective tray cover for refrigerator interior. Shields tray from spills and debris while maintaining clean appearance. Replace if cracked, broken, or missing.

Deli drawer front cover panel for LG bottom-mount refrigerators. Replaces cracked, broken, or discolored decorative cover. Clips onto panel.

Control panel decor trim assembly covers and protects refrigerator controls. Replace when cracked, scratched, or faded to restore appearance. Verify fit.

Refrigerator lamp cover protects the interior light bulb. Replace if cracked, discolored, or broken to restore proper lighting. Verify fit with model.

Replace your refrigerator's LED light assembly to restore bright, even interior illumination. Fixes dim or flickering lights. Confirm fit with your model.

Replaces a cracked, broken, or missing tray cover lid in your refrigerator. Restores proper coverage and helps keep tray contents secure and protected.

Keeps refrigerator drawers aligned and sliding smoothly. Replace if your drawer sticks, sags, or won't glide properly. Confirm fit with your model number.

Guide rail assembly for refrigerator drawers. Installs on drawer sides to keep drawers aligned and sliding smoothly. Replace if rails are cracked or worn.

Restores insulated core inside freezer door to maintain cold retention and reduce frost. Replace when door loses cooling efficiency or frost builds up.

Replace your worn freezer door gasket to restore an airtight seal. Keeps cold air in, reduces frost buildup, and maintains stable temperatures. Confirm fit with your model number before ordering.

Decorative cover for refrigerator door handle. Installs over the handle assembly to provide a finished appearance. Replace if cracked, discolored, or missing.

Cosmetic door handle trim for refrigerator doors. Replaces cracked, broken, or worn handles to restore a secure grip and finished appearance.

Hinge cover assembly for refrigerators. Replaces broken, cracked, or missing hinge covers on door hinges. Restores appearance and protects mechanism.

Covers and protects the refrigerator door hinge assembly. Replace this cap if cracked, missing, or worn to restore a finished appearance and keep hinges clean.

Covers and protects the door hinge area on your refrigerator. Replace if cracked, broken, or missing to restore a finished look and shield wiring.

This name plate displays model and serial numbers on your refrigerator exterior. Replace if cracked, faded, peeling, or missing for proper identification.

Handle assembly for bottom-mount refrigerator freezer drawers. Includes handle and operating mechanism. Replace if cracked, broken, or loose from wear.

Fix condensation or frost buildup on your refrigerator door with this inner foam insulation assembly. Restores thermal performance and sealing efficiency.

Home bar case assembly for bottom-mount refrigerators. Installs in the door to house the drink dispenser. Replace if cracked, damaged, or missing.

Seals the home bar compartment door on your bottom-mount refrigerator. Replace if torn, cracked, or allowing warm air in. Verify fit with model number.

Refrigerator door gasket seals the door to maintain temperature and prevent air leaks. Replace when worn, cracked, or not sealing properly. Confirm fit.

Door gasket creates an airtight seal to keep cold air in and warm air out. Replace if torn, cracked, or no longer sealing properly. Confirm fit by model.

Connects French doors on refrigerators. Replace if cracked, broken, or spring-damaged. Installs between doors to maintain proper seal alignment.

Replacement door basket for bottom-mount refrigerators. Installs on the inner door to organize condiments and beverages. Needed when original is cracked or broken.

Replacement door basket for bottom-mount refrigerators. Installs on the refrigerator door to hold bottles and small items. Replace if cracked or broken.

Replacement door basket assembly for refrigerators. Organizes items in the door compartment. Replace if cracked, broken, or missing to restore storage.

Replacement door-mounted storage basket that restores inside-door shelf space. Needed when original basket is cracked, broken, or missing. Mounts to door.

Molded plastic door basket that mounts on the refrigerator door to hold bottles, jars, and condiments. Replace a cracked, broken, or missing bin.

Stabilizes rotating assemblies in your refrigerator to reduce wobble, wear, and noise. Replace when you notice excessive movement or grinding sounds.

Lower hinge assembly supports and pivots your refrigerator door for smooth operation. Replace if door sags, misaligns, or doesn't seal properly. Confirm fit with your model number.

Door stopper assembly for refrigerators. Installs on the door to limit opening angle and prevent wall damage. Replace if cracked, broken, or missing.

Hinge assembly for refrigerator doors. Installs at door pivot point to support door weight and enable smooth opening/closing. Replace if cracked or worn.

Replace a loose, cracked, broken, or missing refrigerator door handle assembly. Restores a solid grip on the fresh food door and refreshes appearance.

Complete door handle assembly for bottom-mount and French door refrigerators. Replace cracked, bent, or loose handles to restore secure grip and door function.

Plastic rail holder that secures shelf rails inside your refrigerator. Replace this holder if it's cracked, broken, or missing to restore proper shelf support.

Replacement drawer slide rail for refrigerator freezer compartments. Restores smooth drawer gliding when original rail is cracked, broken, or worn out.

Supports and guides refrigerator drawers for smooth gliding. Replace when worn, broken, or causing binding. Confirm fit with your model number.

Fixes non-working dispenser or ice maker caused by damaged wiring. This harness assembly restores electrical connections between components. DIY-friendly repair.

Replace a worn or broken freezer drawer bar connector assembly to restore smooth gliding and proper alignment. Confirm fit with your model number.

Service spanner tool for refrigerator maintenance. Provides secure grip for loosening and tightening service fittings and retaining nuts. Replace if lost.

Secures and aligns refrigerator doors for smooth operation. Replace if doors sag, misalign, or don't seal properly. Confirm fit with your model number.

Replacement ring for your refrigerator. Installs on internal components to secure or seal parts. Order a new ring if yours is cracked or missing.

Center hinge assembly supports and pivots your refrigerator door at mid-point. Replace when door sags or won't close flush. Verify fit by model number.

Upper hinge assembly supports your refrigerator door and ensures smooth opening. Replace when door sags or gaps appear. Verify fit with your model number.

Upper door hinge assembly for bottom-mount refrigerators. Mounts at the top of the cabinet to support the door. Replace if cracked, broken, or lost.

Seals and secures refrigerator air duct connections to maintain proper airflow. Replace if damaged, cracked, or missing. Confirm fit with your model.

Spring component for bottom-mount refrigerators. Installs internally to provide tension or support. Replace if broken, worn, or missing from assembly.

Lever spring for bottom-mount refrigerators. Provides tension for internal lever mechanisms. Replace if broken, stretched, or missing to restore proper fit.

If your refrigerator lever won't return to position or feels loose, this lever return spring restores proper tension for smooth operation. Direct-fit part.

Replacement door hinge spring for refrigerators. Provides tension for smooth door opening and secure closure. Replace if door sags or won't stay closed.

Fix unresponsive or stuck refrigerator buttons with this control panel actuator lever. Restores reliable button feel and switch response. Simple repair.

Internal bracket assembly that mounts and secures the door handle to your refrigerator door. Replace if the bracket is cracked, broken, or stripped threads.

Control panel button won't respond or feels stuck? This push-style lever button restores tactile control to activate dispenser or panel functions. Simple DIY fix.

Magnetic gasket strip that ensures your refrigerator door closes securely and maintains an airtight seal. Replace when door won't stay closed or seal feels weak. Confirm fit with your model number.

Rubber cap for bottom-mount refrigerators. Installs on various internal components. Replace if cracked, worn, missing, or damaged to restore appearance.

Refrigerator not cooling or freezer warm? The compressor assembly circulates refrigerant to maintain temperature. Professional installation recommended.

Refrigerator not cooling or freezing properly? The evaporator coil assembly absorbs heat to cool your fridge. Moderately challenging repair for DIYers.

Compressor won't start? This thermistor assembly monitors temperature and signals the control board to start the compressor. Simple DIY swap.

Refrigerator stopped cooling after power outage? The compressor overload protector prevents overheating damage. Easy DIY fix when compressor won't run.

Fix erratic temperature readings or sensor errors with this PTC sensor cover. Shields the sensor from debris and damage. Simple 5-minute snap-on repair.

Refrigerator not cooling or making unusual noises? This compressor sealing pipe restores proper refrigerant flow. Moderate difficulty repair part.

Drain tray assembly that collects condensation beneath your refrigerator. Replace if cracked, broken, or missing to prevent water leakage issues.

Front cover panel for your refrigerator door. Snaps into place to restore appearance and protect controls. Replace if cracked, broken, or missing clips.

Replaces broken or missing refrigerator door stop. Limits door travel to prevent over-extension and maintain proper alignment and smooth operation.

Precision pin for refrigerator drawer slide roller bearings. Replaces bent, worn, or missing pins that cause drawers to stick or drag. Restores smooth operation.

Support roller that mounts to the refrigerator base, allowing the unit to roll for cleaning or service. Replace if worn, broken, or causing uneven positioning.

Fridge door baffle won't stay flat when opening? This door restrainer spring keeps the baffle panel sealed. Common fix for French door models.

Drier assembly for refrigerators. Installs in the sealed refrigerant system to remove moisture and contaminants. Replace if damaged or worn during repair.

Water pooling under your refrigerator? This drip tray collects condensation and defrost water to prevent leaks and water damage beneath the appliance.

Refrigerator not cooling properly? A faulty condenser assembly may be blocking heat release. This wire condenser restores cooling efficiency. DIY-friendly.

Fix uneven cooling or frost buildup with a refrigerator fan assembly. Restores proper airflow across coils to maintain consistent cabinet temperatures.

Fix uneven cooling or warm spots in your refrigerator with a new evaporator fan blade. This part circulates cold air throughout the unit for consistent temps.

Refrigerator making loud noise or overheating? This fan grille assembly shields fan blades, directs airflow, and reduces noise. Direct-fit replacement.

Fix a refrigerator that's too warm or has frost buildup with this defrost heater. Melts ice from the evaporator to restore proper cooling and airflow.

Refrigerator light stays on or door alarm won't work? This magnet switch senses door position to control interior lighting and alerts. Quick DIY fix.

Fix a stuck or non-working ice/water dispenser with this micro switch. Common cause of dispensers running continuously or not activating. Easy DIY repair.

Fix warm refrigerator or freezer temps with this evaporator fan motor assembly. Circulates cold air throughout compartments. Located behind freezer wall.

Powers the dispenser cover door mechanism on your refrigerator. Replace if the motor has worn out, failed, or no longer operates the cover smoothly.

Uneven cooling or noisy damper? This damper motor support bracket secures the air control assembly for proper airflow between compartments. DIY fix.

Refrigerator not cooling properly? This damper motor support secures the air damper assembly that controls airflow between compartments. Simple DIY fix.

This button holder secures a control panel push button in place so button presses register reliably and the panel stays finished. It restores proper button positioning and prevents the button from falling out or sticking. What it does:

• Holds a control panel push button in the correct position for reliable operation
• Keeps the button aligned so presses engage the switch or membrane consistently
• Prevents the button from popping out or becoming loose during normal use
• Helps maintain the appliance's finished appearance around the control area

• One button holder

• Turn power to the appliance off before attempting any service to avoid shock or injury
• Remove the control panel or bezel per the manufacturer's instructions to access the holder
• Inspect surrounding buttons and switches for wear; replace damaged components as needed

Replacement handle cap that covers and secures the end of a refrigerator or freezer door handle for a finished appearance and to protect exposed hardware. Restores a clean look and hides fasteners. What it does:

• Covers the exposed end of a door handle to conceal screws and mounting holes.
• Protects handle hardware from dirt and wear.
• Improves the appliance's appearance when an original cap is cracked, broken, or missing.
• Helps prevent snagging on a damaged or loose handle end.

• High-level snap-on or screw-on installation; handle removal may be required for access.
• Use basic hand tools as needed and avoid forcing parts to prevent damage.
• Confirm fit and finish before final installation.

This door stopper cushions and limits the travel of a refrigerator door to prevent slamming and reduce wear on the hinge and cabinet. Replaces a worn or broken stopper to restore smooth, controlled door movement. What it does:

• Acts as a bumper and travel limiter to prevent the door from hitting the cabinet
• Absorbs impact to reduce noise and protect hinge components
• Helps the door close and align properly when opening and closing
• Commonly replaced when cracked, missing, or excessively worn

• Turn off and unplug the appliance or disconnect power before starting any work
• Remove the hinge or door trim as needed to access the stopper following the manufacturer service instructions
• Replace the stopper by removing the old piece and securing the new stopper in the same position; retain original fasteners unless replacement is required

Fix a sagging or misaligned refrigerator door with this replacement door support bracket. Restores proper alignment and prevents door rubbing issues.

Fixes refrigerator not powering on or functions not working. This main control board manages all refrigerator operations. Requires rear panel removal.

Supports and stabilizes your refrigerator door for proper alignment. Replace if bracket is cracked, broken, or causing door misalignment issues.

Restores screen illumination by replacing failed backlight strip. Returns even, bright lighting to LCD panel for clear picture and menu visibility. Verify fit with your model number before ordering.

Compressor humming but not starting? This start capacitor provides stable starting power to your refrigerator compressor. DIY-friendly repair.

Refrigerator won't start or compressor struggles to run? The run capacitor provides the power boost needed to start and maintain compressor operation.

Fixes refrigerator power loss, sparking, or intermittent operation. This power cord assembly restores safe electrical connection from wall outlet to appliance.

Refrigerator not cooling evenly or running constantly? This DC motor assembly drives the fan to restore proper airflow and temperature control in your fridge.

Fix a refrigerator that won't cool, has no display, or shows error codes with this main control board. Controls cooling, ice making, and temperature.

Protective cover assembly that shields the printed circuit board (PCB) in your refrigerator. Replace if cracked, broken, or missing to protect electronics.

Replace a cracked or scratched control panel display cover. This assembly protects buttons and the display screen from wear while restoring appearance.

The Ice Maker Assembly Kit is an OEM part for LG refrigerators. This kit includes all the necessary components to produce ice efficiently, ensuring your refrigerator maintains a steady supply of ice for your household. The kit also features a 20-pin and 3-pin wiring harness.

Causes of a bad ice maker assembly can include wear and tear over time, mineral buildup from hard water, or electrical malfunctions. Additionally, damage can occur due to improper handling or issues with other components in the ice-making system.

Symptoms of a bad ice maker assembly include:

• No ice production
• Slow ice production or smaller ice cubes
• Ice cubes that are misshapen or irregular
• Leaking water around the ice maker
•  Unusual noises during the ice-making process

This OEM LG part is also compatible with Sears/Kenmore.

Refrigerator not cooling properly? A failed evaporator fan motor stops cold air circulation. This motor replacement restores airflow across the coils.

Fix inaccurate temperature readings or sensor errors with this refrigerator sensor control board. Restores proper sensor communication and feedback.

Freezer not cooling below 24°F or refrigerator running too warm? This defrost thermostat sensor monitors temperature and signals the control board.

Fix a refrigerator that won't dispense ice or water with this dispenser lever. Controls crushed ice and water flow through the door mechanism.

Replaces damaged duct vent cap assembly on your refrigerator. Install when cap is cracked, broken, or missing to restore proper airflow. Verify fit with your model number before ordering.

Stores and supplies water to your refrigerator's dispenser and ice maker. Replace if cracked, leaking, or damaged from mineral buildup or freezing.

Leaking water line connections? This inline tube connector joins two sections of tubing for a secure, leak-resistant seal. Quick 10-minute fix.

Fix water leaks from your refrigerator with this water line tube assembly. Stops leaks caused by brittle or kinked tubing and restores normal flow.

Fix water leaks from your refrigerator with this water line tube assembly. Stops leaks caused by brittle or kinked tubing and restores normal flow.

Fix no water or ice issues with this water inlet valve. Common when ice maker won't fill or dispenser trickles. Easy 10-minute DIY with video guide.

Leaking water from your refrigerator or no water/ice from dispenser? This water inlet valve controls flow to ice maker and dispenser. DIY repair in 30 min.

Plastic cover cap for refrigerators. Snaps onto hinges, handles, or shelving brackets to conceal mounting hardware. Replace when cracked or missing.

Replace your refrigerator's water filter cover to protect the filtration system and maintain proper seal. Check your model number for exact fit compatibility.

Restores clean-tasting water and steady flow by filtering sediment and contaminants. Replace every 6 months or when flow weakens. Verify fit with your model.

Replace a broken or leaking water filter housing that prevents water flow to your dispenser and ice maker. Direct fit for bottom-mount refrigerators.

Covers and protects refrigerator tubing inside the cabinet. Replace this tube cover if the original is cracked, broken, or missing to restore proper appearance.

Replace your refrigerator's water filter cover to protect the filtration system and maintain proper seal. Essential when cover is cracked or missing. Confirm fit with your model number.

This replacement pipe holder secures a small appliance pipe or tube in place, reducing movement and vibration to help prevent noise, wear, or accidental disconnection. It restores proper routing and support for the pipe. What it does:

• Secures a pipe or tubing to the appliance frame or chassis to keep it from shifting
• Reduces rattling or vibration caused by loose plumbing or tubing
• Helps maintain proper alignment to avoid chafing or contact with other components
• Useful when a cracked, broken, or missing clip allows pipe movement

• Turn off and unplug the appliance before accessing internal components
• Remove any panels or covers to reach the pipe clip location
• Snap the clip over the pipe into the existing mounting tab; replace any damaged mounting hardware

Refrigerator pipe holder bracket secures water lines and tubing in place. Replace if cracked, broken, or missing to properly support pipes inside your fridge.

Home bar cover panel for bottom-mount refrigerators. Replaces cracked, broken, or missing exterior home bar covers. Restores appearance and finish.

Secures and pivots the ice bank door for smooth opening and proper sealing. Replace if door sags, won't close, or ice dispenser misaligns. Confirm fit.

Seals the ice bin compartment to prevent warm air and moisture intrusion. Replace when worn or torn to reduce frost buildup and ice clumping.

Seals the refrigerator door to keep cold air in and moisture out. Replace when worn or deformed to restore proper cooling and reduce frost buildup.

Molded trim cover that fits over the ice maker door lever on bottom-mount refrigerators. Replace if cracked, broken, or missing to restore appearance.