Dryer Turn Small Engine Ignition Coil Parts

The LP Conversion Kit is an OEM part for Whirlpool dryers. It allows the dryer to be converted from natural gas to liquid propane (LP), ensuring safe and efficient operation with LP fuel.

Causes of needing an LP conversion kit can include relocating to an area where only LP gas is available or choosing LP gas due to its efficiency and lower environmental impact. It is essential to use the proper conversion kit to avoid potential safety hazards and ensure the dryer operates correctly.

Symptoms indicating the need for an LP conversion kit include:

• Moving to a location with only LP gas availability
• Decision to switch from natural gas to LP for efficiency or environmental reasons

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Natural Gas Limiter is an OEM replacement part for Whirlpool dryers. Located where the gas supply connects, it regulates safe flow levels to fuel burners during heating cycles. Precise control prevents over-firing issues.

Symptoms of a faulty limiter include:

• Dryer not achieving proper temperatures or taking too long
• Yellow flames indicating abnormal gas-to-air ratios
• Fault codes showing problems with gas valve readings

Causes can range from debris accumulation reducing gas flow to mechanical wear of linkage components. This replacement restores optimized operation.

This OEM replacement part is compatible with select KitchenAid and Maytag brand models.

The Natural Gas Orifice is an OEM replacement part for Whirlpool gas dryers. Installed within the dryer burner assembly, it regulates gas fuel flow into the burner.

Common causes relate to natural deposits obstructing the small gas port, as well wear inducing intermittent ignition of flames during many years of laundering cycles.

Symptoms of a failed orifice include:

• Slow or inefficient drying times and extended cycles
• Uneven or incomplete drying of loads
• Changes in flame appearance like higher than normal yellow tips

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

The Liquid Propane Gas Orifice is an OEM replacement part for LG dryers. This orifice is specifically designed for models that run on liquid propane gas. It regulates the flow of gas into the burner, allowing the dryer to heat up and dry your clothes.

Causes of a faulty orifice can include corrosion from repeated heating cycles breaking down internal components. Orifices degrade naturally over extended use.

Symptoms of a failed orifice include:

• The dryer failing to properly heat or dry clothes
• Yellow flames or plumes of unburnt gas exiting the dryer vent
• Error codes related to gas or heating issues displayed

This OEM LG part is also compatible with some Kenmore models.

For natural gas order 4948EL4001B.

This is an igniter and bracket assembly, and it is intended for use in dryers. This is a genuine replacement part made by Speed Queen. The igniter is connected to the dryer on the back of the appliance, and it is used to heat the drying tub. A new igniter and bracket assembly might be needed if the dryer is unable to reach the correct temperature. If the heat in the dryer seems inconsistent during any drying cycle the igniter might be bad and will need to be replaced. For this repair the user will need access to the back of the appliance. Be sure the dryer is completely powered down and cooled before attempting to repair. This is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with Dryers made by Speed Queen.

The Ignitor is an OEM part for Frigidaire dryers. This part ignites the gas burner that generates the heat necessary for drying clothes.  Note: Part has been redesigned and is now a flat style ignitor instead of round ignitor.

Causes of a bad Ignitor can include wear and tear from regular use, electrical issues such as short circuits or power surges, and physical damage from debris or residue buildup.

Symptoms of a bad Ignitor include:

• The dryer not heating up, leading to clothes remaining wet after a cycle
• The ignitor not glowing or sparking when the dryer is turned on
• Extended drying times due to insufficient heat production
• The smell of gas without ignition, indicating a failure to light the burner

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Natural Gas Orifice is an OEM part for Whirlpool dryers. This part regulates the flow of natural gas to the burner, ensuring efficient and safe combustion for proper drying performance.

Causes of a bad natural gas orifice can include buildup of debris or lint, wear and tear over time, or damage from improper handling during maintenance.

Symptoms of a bad dryer natural gas orifice include:

• The dryer not heating up
• Inconsistent or weak flame in the burner
• Longer drying times than usual
• Unusual gas odors or hissing sounds

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Ignitor Assembly is an OEM replacement part for Frigidaire dryers. It serves as the ignition source safely firing up burners to initiate drying cycles. 

Causes usually relate to the continual thermal shock experienced from heating and then rapidly cooling over extended use. As a foundational safeguard, ignitors require OEM replacement when arcing declines. 

Symptoms of a faulty ignitor can include:

• The dryer fails to start or stop heating intermittently   
• Cycles taking overly long to complete or feel uneven
• Excessive service calls relating to "no heat" troubles  
• Risk of uncombusted gas pooling in dryer if ignition falters

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Igniter Assembly is an OEM part for Whirlpool dryers. This part ignites the gas burner to produce heat for drying clothes. It plays a crucial role in the dryer's heating process, ensuring that the gas is ignited safely and efficiently.

Causes of a bad igniter assembly can include general wear and tear, electrical surges, or damage from repeated heating and cooling cycles. 

Symptoms of a bad igniter assembly include:

• Dryer not heating
• Clothes taking longer than usual to dry
• No glow from the igniter
• Intermittent heating during cycles

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This genuine OEM replacement part is a burner and gas valve assembly for dryers. The burner and gas valve assembly is a complete assembly that contains the burner that distributes the gas in a way that creates an even flame allowing for heat to be distributed properly to perform the dryer's essential function. If the dryer is no longer drying clothes effectively or heating properly, then it might be time for it to be replaced. Luckily repairing a gas valve assembly is a relatively simple job.To replace the burner and gas valve assembly, begin by shutting off power to the appliance. Next, pull the dryer away from the wall to gain access to the back panel. Remove the back panel and locate the burner and gas valve assembly. Remove the mounting screws that hold it in place. After removing the screws use both hands to pull and release the old burner assembly. Set it off to the side and proceed to install the new one by refastening the screws that hold it in place.This replacement part is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand washers.

This burner tube channels the gas-air mixture to the burner and includes an adjustable air shutter to set proper combustion. Replacing a damaged assembly helps restore reliable ignition, stable flame, and consistent heating performance.

• Directs the fuel/air mixture from the gas valve to the burner port
• Integrated adjustable shutter regulates primary air for proper flame
• Helps maintain efficient heat output and reliable burner operation
• Failure can present as no or intermittent heat, burner that lights then goes out, yellow/lazy flame, or soot

• Disconnect power and shut off the gas supply; allow the appliance to cool before servicing
• Access the burner compartment and transfer any clips/brackets from the original tube
• Note the current shutter position; after installation, adjust for a steady blue flame
• After reassembly, leak-test gas connections with a soap solution and verify burner operation

This LP conversion kit contains the calibrated components needed to convert compatible natural gas appliances to operate on liquid propane, helping ensure proper fuel flow and flame performance when switching gas sources.

• Provides propane-rated orifices and components to adjust gas flow from natural gas to LP
• Helps correct issues like yellow, lazy, or oversized flames after a fuel change
• Supports safe, efficient burner ignition and heating on LP
• Used when local fuel supply is propane instead of natural gas

• For safety, shut off gas and electrical power before beginning; allow the appliance to cool
• Conversion must follow the appliance's service manual and LP instructions
• Adjust regulator setting and burner/orifice sizing per included and model-specific guidance
• Leak-test all gas connections with an approved method before restoring service

This replacement igniter lights the gas burner in your range or wall oven, restoring reliable starts and consistent heat. Swap in a fresh igniter to resolve hard-to-light burners and no-heat situations so cooking cycles begin as they should. What it does:

• Provides the ignition source to light the bake or broil burner flame
• Helps ensure fast, consistent burner light-off at the start of a heat cycle
• Common symptoms of failure: no ignition/no heat, delayed or intermittent ignition, repeated clicking without flame, or a gas odor before light-off

• 1 igniter assembly

• Disconnect power and shut off the gas supply before servicing; allow the appliance to cool completely
• Note wire connections and mounting orientation from the original part for correct reassembly
• Handle the ceramic/element carefully to avoid damage
• After installation, restore gas and power, then check for leaks with a soap solution

If the mounting clip is burnt order WE1X941.

The Dryer Gas Valve is an essential component for your Samsung dryer, ensuring proper gas regulation and efficient drying performance. This genuine OEM part guarantees a perfect fit and reliable operation, matching the exact specifications of your appliance. Designed for durability, the Dryer Gas Valve maintains consistent gas flow, preventing interruptions during your drying cycles and enhancing overall dryer efficiency. Installing this gas valve helps restore your dryer's functionality, especially if the original component is faulty or worn out. Compatible with a wide range of Samsung dryer models, this part provides peace of mind with its high quality and dependable performance. Choosing this genuine OEM Dryer Gas Valve ensures safe operation and extends the lifespan of your Samsung dryer, allowing you to manage your laundry needs effectively and without hassle.

The LP Gas Conversion Kit is an OEM part for Whirlpool appliances. This kit allows for the conversion of natural gas appliances to use liquid propane (LP) gas. It includes all necessary components, such as orifices and instructions, to ensure a safe and efficient conversion.

Over time or due to specific needs, you might need to convert your appliance from natural gas to LP gas. Causes for needing this conversion include moving to an area where only LP gas is available or preferring LP gas due to its efficiency and environmental benefits.

Symptoms indicating the need for a gas conversion kit include:

• Moving to a location that only supplies LP gas
• Changing energy preferences for better efficiency
• Appliances set up for natural gas needing adaptation to LP gas

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.