Washer Cold Pump Hose Parts

This replacement filter traps debris and contaminants within your appliance's system to help protect internal components and maintain proper performance. Swapping a clogged or damaged filter can restore flow/airflow, reduce odors and buildup, and support efficient operation. What it does:

• Captures grease, lint, dust, or food particles to prevent recirculation and protect internal parts
• Supports proper airflow or fluid flow for ventilation, circulation, or drainage
• Helps minimize odors and residue caused by a saturated filter
• Typical signs it's due: visible tears/warping, heavy buildup, restricted airflow/venting, lingering odors

• 1 filter

• Disconnect power before servicing and allow any hot surfaces to cool
• Note the filter's orientation and any tabs/clips; install the new filter the same way
• Clean the surrounding housing or channel before installation
• Do not operate the appliance without required filter(s); follow your model's maintenance schedule

This water recirculation pump moves wash water through the washer's recirculation circuit to help saturate loads and improve cleaning. Replacing a failed pump restores proper water movement and wash performance.

• Circulates water from the tub/sump back through the recirculation line during wash
• Maintains flow through the dispenser or spray nozzle for better saturation
• Replaces a pump that is noisy, leaking, seized, or not moving water
• Symptoms include no recirculation spray, reduced cleaning results, or a humming motor without water movement

• Disconnect power and turn off water supply before servicing
• Access is typically from the lower front or rear service panel; place towels to catch residual water
• Transfer hoses, clamps, and the electrical connector from the old pump to the new one
• Ensure correct hose routing and secure connections; check for leaks during a quick test cycle

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

The Pump Assembly is an OEM part for Frigidaire washing machines. This part is responsible for draining the water from the washer at the end of each wash cycle.  

Causes of a bad Washer Pump Assembly can include:

• Obstructions in the pump or its inlet/outlet hoses, which can hinder water flow.
• Wear and tear on the pump's motor or impeller, reducing its effectiveness in water evacuation.
• Electrical issues, such as faulty wiring or connections, that prevent the pump from operating.

Symptoms of a failing Washer Pump Assembly include:

• Water not draining properly from the machine.
• The washer fails to enter the spin cycle due to the presence of excess water.
• Unusual noises during the drain phase, indicating a struggling or damaged pump.
• Error codes displayed on the washing machine that indicate drainage problems.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This drain pump assembly moves water out of the washer during the drain and spin parts of the cycle. Replacing a weak, noisy, or leaking pump restores proper draining, prevents standing water, and helps cycles finish correctly.

• Pumps wastewater from the tub to the household drain
• Supports proper spin performance by clearing water from the tub
• Common symptoms: won't drain or drains slowly; water left in tub; loud humming/grinding from pump area; leaks around the pump; cycle stops with a drain-related error
• A clogged hose or debris in the pump can mimic failure—inspect for obstructions

• Disconnect power and water supply; wear gloves. Bail or wet-vac remaining water and place towels or a pan to catch spills
• Clamp and remove inlet/outlet hoses; note hose orientation and routing
• Move wiring connector(s) one at a time to the new pump and secure the pump in place
• Ensure hoses are clear and clamps tight; run a drain/spin test and check for leaks

This drain pump assembly removes water from the washer tub during the drain portions of the cycle, helping ensure proper rinsing and spinning and preventing water from remaining in the machine after a wash.

• Pumps wastewater from the tub through the drain hose to the household standpipe
• Common failure symptoms include the washer not draining, water left in the tub, loud humming or grinding from the pump area, or leaks around the pump/hose connections
• Restores proper drainage to support effective spin performance

• Disconnect power and turn off water supply before servicing; bail or wet-vac any standing water
• Keep towels or a pan handy to catch residual water when removing hoses
• Mark hose positions and transfer any existing mounting brackets or connectors from the old pump as needed
• Inspect and reseat hose clamps and the drain hose to ensure a watertight seal before testing

This pump and hose assembly replaces the appliance's drain pump to restore reliable water removal and prevent standing water or leaks. Use this direct-fit assembly when the unit won't drain or you see leaks from the pump area. What it does:

• Pumps drain water from the appliance and routes it out through the drain hose.
• Restores normal drain cycles when a failed pump stops water removal.
• Helps stop water pooling or leaking near the pump area.
• Reduces grinding, humming, or abnormal noises tied to a failing pump.

• Always disconnect power and shut off water to the appliance before servicing.
• Secure hose connections and clamps; check routing to avoid kinks.
• After installation, restore power and run a short drain cycle to check for proper operation and leaks.

Includes connector and both clamps.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Contains two, six foot long braided hoses with 90 degree ends.

This pump and brake assembly drains water from the tub and applies the basket brake in your top-load washer. Replacing a worn assembly restores proper draining and a safe, prompt basket stop between cycles. What it does

• Pumps water out of the washer during drain and spin phases
• Applies the brake to stop the spin basket between cycles or when the lid switch is activated
• Helps reduce extended coast-down and stopping squeal
• Typical symptoms: standing water, slow/no drain, leaking at the pump area, basket coasts too long or squeals when stopping

• One pump and brake assembly

• Disconnect power and water supply; drain remaining water from hoses before service
• Access from the washer's underside; support the unit securely
• Transfer existing hoses/clamps to the new pump and secure all connections; if belt-driven, verify proper belt routing and pulley alignment
• Run a brief fill/drain test and recheck for leaks and proper basket stop

Hose washer and plastic insert for inlet hose. To order separately: for washer use WPY013783, for strainer use WP22002960.

Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separately: WP356138

Size: 21 inches long. Clamp included.

This inlet hose carries supply water into the washer during the fill cycle. Replacing a worn or leaking hose restores proper water flow and helps prevent leaks and fill errors that can leave clothes unwashed or floors wet.

• Channels incoming water from the inlet valve into the washer
• Maintains a sealed connection to prevent drips and leaks
• Replaces hoses that are cracked, swollen, kinked, or clogged with mineral deposits
• Common symptoms: water leaking during fill, reduced water flow or fill error codes, visible cracks/splits

• Disconnect power and turn off both water supply valves before servicing
• Keep towels or a container handy; residual water may spill when removing hoses
• Note hose routing; fully seat ends and secure with existing or new clamps as required
• Restore water and power, then run a quick fill to check all connections for leaks

This is the water pump that moves water through your appliance so cycles can run correctly. Replacing a failing pump restores proper water flow and helps prevent standing water, poor performance, and leaks. What it does:

• Circulates and/or removes water as the appliance operates
• Supports proper flow so wash/rinse/drain steps can complete
• Maintains a sealed path at the pump connections to help prevent leaks
• Typical symptoms of a failing pump: standing water, weak/no water movement, loud humming or grinding from the pump area, leaks, or related drain/circulation errors

• 1 water pump

• Disconnect power and shut off water supply before servicing
• Have towels/containment ready; some residual water is normal when hoses are removed
• Move wires and hoses one-for-one to the new pump; tighten clamps and check any O-rings/seals
• Run a short test cycle and inspect for leaks and proper water movement