106-565-39400 Parts

Replaced filter cap with new one. The minor challenge was to find a method of pulling the filter out of refrigerator (which is normally done by pulling on the filler cap. The filter was recessed to far into the refrigerator for me to be able attach the new cap. I had to find another tactic to remove the filter. The solution was to look at the replacement filter to notice where two slots were located at the end of the filter. I then used a paint can opener (found at most paint stores) to slip... Read more

• Fridge too cold
• Fridge too warm

The site came up on a Google search suggesting a new air diffuser which was indeed the problem. I got a thermistor too just in case but probably want needed. Saved a fortune compared to a repair man and was able to cancel an order I had for a new unit saving over $1200+! Very happy with the whole process and videos on you tube etc. Great site! Thanks! Read more

Very easy to replace. Take off cover to auger compartment. Unplug power connector from auger motor. Remove four screws holding auger motor to refrig. Put new auger motor in place, insert screws, insert power connector, replace cover. Use ice maker! Read more

The problem was that the motor coupler & shaft had a tiny bit of rust at their union. With the weight of the ice bin it rusted in the lowest position. This didn't allow the motor coupler to float on the shaft. There is a spring inside the shaft that pushes up on the motor coupler keeping it engaged in the ice bin coupler above. This coupler in turn rotates the auger in the bin to dispense the ice. I removed the motor coupler & shaft, tapped the coupler loose and filed off the rust. This allowed... Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

After watching installation videos on each felt I could pull it off and ordered and received replacement water reservoir and water dispenser tube assembly. Reservoir installation went off without a hitch outside of the added step of the need to remove the entire main in waterline assy in order to access the connectors which also were not as represented in video, in that they were not the press-to-release type but standard threaded compression types. Water Dispenser tube/spout assembly was much... Read more

• Leaking

I have a Whirlpool Side-by-side Model ED22PWXBW01. A year ago, the ice cubes started freezing together in the rear of the ice bin for no apparent reason. Although the problem started off small, it gradually grew much worse, and finally I could see water dripping out of the ice mold and into the bin during the fill cycle. Re-levelling the refrig didn’t help, nor did adjusting the cube size / fill level. With guidance from the video, I removed the icemaker from the wall of the freezer. The... Read more

With the help of the fantastic videos provided on the web site for each replacement part, it was extremely easy to complete the repair Read more

I noticed Ice maker Quit for the third time in 15 years so I decided to buy another Ice maker, I installed it and NO ice still?? Well I went after the other problem thinking if it does not get cold enough maybe ice maker won’t work. I ordered Defrost Switch, Heater and Evaporator Fan just to be safe. I replaced all three, the fan was noisy, the heater OHM’d ok but I replaced it as did the defrost switch, I put it back together, the Freezer got to 0 degrees and the frig got to 38 degrees so I... Read more

The problem was that the motor coupler & shaft had a tiny bit of rust at their union. With the weight of the ice bin it rusted in the lowest position. This didn't allow the motor coupler to float on the shaft. There is a spring inside the shaft that pushes up on the motor coupler keeping it engaged in the ice bin coupler above. This coupler in turn rotates the auger in the bin to dispense the ice. I removed the motor coupler & shaft, tapped the coupler loose and filed off the rust. This allowed... Read more

Easy to remove the metal parts from the old bin. The only problem was that the screw that holds the adapter has red thread locker and screwdriver rounded off the head of the screw. Drilled the screw and heated the screw to loosen the thread locker and used an ease out to remove the screw. Read more

Cut piece to fit Read more

Put the new hinges on the doors fyi you need to tell what size the screws are for the hinge kits would help a lot Read more

• Light not working

I saw your video on you tube and it seems very easy to do it my self, so I ordered the parts and I did it my self. It was very easy. Thank you for sharing with us on how to did it. One more thing, the parts arrived on the time they said it would come. Read more

Replaced icemaker and shutoff arm. Easy project. Read more

Found the parts in the diagram of my fridge and simply installed it very easy Read more