970-688530 Parts

Restore dependable oven-light operation. This door-activated switch turns the oven's interior light on when the door opens and off when it closes, letting you check food at a glance and preventing the light from staying on unnecessarily. What it does:

• Detects door position to control the oven cavity light on/off
• Worn or stuck contacts can make the light stay on with the door closed
• Failed switch can prevent the light from turning on when the door opens
• Intermittent or flickering light may indicate a failing switch

• 1 switch

• Disconnect power to the appliance before servicing
• Access the switch (typically mounted in the front frame near the door opening)
• Move wires to the new switch one at a time to maintain correct placement
• Reinstall, then test door/light operation before final reassembly

This clamp secures a hose to its fitting, maintaining a tight, leak-resistant seal at the connection. Replace a fatigued or missing clamp to help prevent drips and stop hoses from working loose under vibration.

• Holds a hose firmly on a pump, tub, dispenser, or valve outlet
• Maintains clamping force to help minimize leaks at the joint
• Helps keep hoses from slipping off during operation
• Common signs: water at a hose joint, loose/slipping hose, damaged or corroded clamp

• Disconnect power and shut off water supply before servicing
• Place a towel or pan to catch residual water at the connection
• Note hose position; remove the old clamp, seat hose fully on the fitting, position the new clamp over the bead, and secure
• After reassembly, run a short cycle and check for leaks

This replacement bolt secures internal components in your appliance. A stripped, rusted, or missing bolt can let parts loosen and vibrate; installing a new bolt restores a tight, stable connection for reliable operation.

• Provides a secure, threaded fastener for brackets, weights, or assemblies
• Helps maintain alignment and reduce movement during operation
• Typical issues: missing hardware, stripped threads, or visible corrosion
• Helps address rattling or excessive vibration caused by loose hardware

• Safety first: Disconnect power; for water- or gas-connected units, shut off supplies
• Support the component being secured before removing the old fastener
• Start threads by hand to avoid cross-threading; tighten evenly to manufacturer guidance—do not overtighten
• Reuse original washers/spacers and thread locker only if they were originally present

This is a nut that is used in many microwave ovens. It is typically used to hold interior fan in place. A nut is a fastener that is used to hold two items together or keep one component secure against a surface. Use and time can cause the nut to become stripped, damaged, or broken. If the nut is broken, it will no longer hold the fan in the right location. The nut will need to be replaced.Before replacing this part, the microwave should be unplugged. Open the refrigerator door and remove the cover that goes over the fan. The nut can then be removed using a nut driver. Replace the other parts before using the appliance.This nut is used in microwave ovens manufactured by Crosley, Electrolux, Frigidaire, and Kenmore. It is sold as a single part. This is an authentic OEM replacement part is sourced directly from the manufacturer.

This electronic control board manages your appliance's core functions and timing. Replacing a failed board restores proper operation when controls are unresponsive or cycles won't run as designed. What it does

• Distributes power to key components and executes programmed cycles
• Monitors inputs from switches/sensors and controls motors, valves, and heaters as needed
• Can resolve symptoms such as no power to controls, won't start, or cycles not advancing
• Address intermittent operation, error codes/abnormal beeps, or unexpected shutdowns

• 1 electronic control board

• Disconnect power before servicing; verify no voltage is present
• Use ESD precautions and handle the board by the edges only
• Photograph/label wiring and move connectors one at a time to the new board
• Ensure all connectors are fully seated and the board is mounted securely before test

This genuine replacement spring restores proper tension and smooth movement in the affected mechanism, helping your appliance operate reliably. Replacing a weakened or broken spring can reduce noise and correct misalignment caused by lost tension.

• Maintains tension and provides return force for connected levers, brackets, or linkages
• Helps keep components in position and minimizes excess play or rattling
• A weakened, stretched, or broken spring can cause poor engagement or inconsistent operation
• Common signs include parts not returning to rest, excess slack, or new noises from the area

• Disconnect power; also shut off water supply
• Note the spring's hook orientation and routing; take a reference photo before removal
• Control the spring with pliers and wear gloves/eye protection to avoid snap-back injuries
• Inspect related brackets/retainers and replace any worn components to ensure proper tension

Specs: Hex head ,1/4-20 x 5/8

This water level pressure switch senses tub water level through an air hose and signals the control when to stop filling and allow spin. Replacing a failed switch restores proper fill levels and reliable cycle progression. What it does:

• Monitors water level via air pressure from the tub's air dome hose
• Signals the control to start/stop filling at the correct level
• Prevents overfilling and enables spin only when the tub is empty
• Common symptoms: overfills or underfills, won't fill, keeps filling, won't advance or won't spin

• Pressure switch

• Disconnect power and water supply before servicing
• Access the switch (typically under the top or rear panel) and release its mounting clip/screws
• Transfer wires one at a time; move the air hose to the new switch and ensure a tight, unobstructed connection
• Secure the switch and run a test fill/spin; inspect the air hose for kinks, cracks, or soap residue

This center hinge spacer sits on the refrigerator's center hinge pin to keep the door properly spaced and pivoting smoothly. Replacing a worn spacer helps restore even door alignment and a reliable gasket seal for easier opening and closing. What it does

• Maintains the correct gap between the door and center hinge to prevent metal-to-metal wear
• Supports smooth, quiet door movement on the hinge pin
• Helps keep the door level so the gasket seals evenly
• Worn or missing spacers can lead to door sagging, rubbing/squeaking, or doors that don't close cleanly

• One center hinge spacer

• Disconnect power and remove items from the door; support the door before loosening hinge hardware
• Lift the door off the center hinge pin and remove the old spacer
• Place the new spacer on the hinge pin, reinstall the door, and check alignment and seal
• Re-tighten hinge fasteners and verify the door opens/closes smoothly

This air duct seal creates a tight barrier between the dryer's lint housing and cabinet. Replacing a worn seal helps prevent air leaks, maintain proper airflow through the lint filter, and restore consistent drying performance.

• Seals the air duct/lint housing to the front panel to direct airflow through the lint screen and drum
• Helps maintain dryer efficiency and temperature control by preventing bypass air leaks
• Common symptoms of a failed seal include longer dry times, weak exhaust airflow, excess lint inside the cabinet, or lint around the door opening
• Replaces a deteriorated or missing seal to restore the intended air path

• Disconnect power; shut off gas supply for gas models
• Access the air duct by removing the lint screen and top/front panels as needed
• Remove the old seal and any residue; clean mating surfaces before installing the new seal
• Seat the duct evenly against the panel when reassembling to ensure a uniform seal

This dryer control thermostat regulates internal temperature by cycling the heater on and off. Replacing a failed thermostat restores proper, consistent drying temperatures to protect fabrics and improve overall drying performance.

• Monitors exhaust temperature and opens/closes contacts to maintain target heat
• Helps prevent underheating and overheating during drying cycles
• Common symptoms of failure: no heat or low heat, long dry times, runs too hot, inconsistent temperatures
• A sticking thermostat may cause the high-limit safety to trip

• Disconnect power before servicing
• Access location varies by model; typically mounted on the blower or heater housing
• Move wires one at a time from the old thermostat to the new one; ensure tight, secure connections
• After replacement, clean the lint path and verify exterior venting for proper airflow

Replacement glass panel that restores visibility and helps protect internal components for compatible Frigidaire appliances. Use this glass to replace cracked, chipped, or shattered panels and return your appliance to safe, usable condition. What it does:

• Replaces broken or damaged glass panels used on the appliance door, shelf, or panel area.
• Stops loose shards and visible cracks that can cause safety concerns or interfere with normal use.
• Restores clear visibility through the door or panel.
• Helps prevent further damage to internal components by replacing compromised glass.

• Disconnect power and unplug the appliance before beginning any repair.
• Handle with care and wear cut-resistant gloves and eye protection; glass edges may be sharp.
• May require partial disassembly for removal and installation—follow OEM instructions.

This electronic control board is the appliance's "brain," directing power and timing to key components. Replacing a failed board restores proper operation, responsive controls, and reliable cycle performance. What it does:

• Interprets inputs from the control panel and sensors, then executes programmed cycles
• Distributes power to motors, pumps, valves, and other components as needed
• Manages timing, sequencing, and safety interlocks during operation
• Supports self-diagnostics; faults may present as error codes or lights
• Common symptoms of a failed board include no power, won't start, stops mid-cycle, unresponsive controls, or erratic behavior

• 1 electronic control board

• Disconnect power to the appliance before servicing; observe ESD precautions when handling the board
• Photograph wiring and move connectors one at a time to the new board
• Ensure all plugs are fully seated and the board is properly mounted before reassembly
• Some models require an initialization or programming step—follow the unit's service/tech sheet after installation

This small spacer fits on the idler assembly shaft to properly space and align the belt tensioner. Replacing a worn spacer helps keep the drive belt tracking correctly so the drum/tub runs smoothly and quietly. What it does:

• Spaces and centers the idler pulley on its shaft
• Helps maintain proper belt alignment and tension
• Can reduce squeaking or chirping from the idler area
• A worn or missing spacer may let the belt ride off, fray, or stop the drum/tub

• 1 idler spacer

• Disconnect power before servicing; let hot components cool
• Access the idler assembly per your model, relieve belt tension, and remove retaining hardware to slide off the pulley and old spacer
• Install the new spacer in the same location/orientation; reassemble and route the belt correctly
• Rotate the drum/tub by hand to verify smooth belt tracking before restoring power

This factory screw secures panels, brackets, and other components in your cooking appliance. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and keep parts properly aligned during use.

• Fastens components to maintain proper alignment and stability
• Helps prevent vibration, rattling, and loose parts during operation
• Replace if threads are stripped, the head is damaged, or the screw is missing
• Commonly used to mount internal or exterior parts in ranges and wall ovens

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Use the correct driver bit to avoid stripping the screw head
• Install in the original location and do not overtighten
• If the receiving threads are damaged, repair or replace the mating part before installation

This is the graphic control panel overlay for the oven/range user interface. It restores legible labels and a clean appearance for touchpad buttons, helping you see and select functions accurately when the original film is worn, bubbled, or damaged. What it does

• Adheres to the control panel/touchpad to provide printed button labels and icons
• Protects the underlying keypad from spills and cleaning wear
• Helps resolve faded, peeling, or unreadable control markings
• Can improve button feel and responsiveness when the old overlay is lifting
• Restores a finished, factory look to the control panel

• One control panel graphic overlay

• Disconnect power to the appliance before starting
• Clean and dry the control panel surface thoroughly; remove all adhesive residue
• Align carefully before applying—once set, adhesive may not reposition cleanly
• Press firmly and evenly to ensure full adhesion and avoid bubbles