Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Oven light stays on or won't turn on when door opens? This door-activated switch restores automatic light control. Easy 15-minute DIY repair.
Replaced light switch Read more
Secures hoses to pumps, tubs, and valves preventing leaks. Replace if worn, loose, or causing drips during cycles. Confirm fit with your model number.
New hose and clamp. Read more
Fix leaking or noisy washer drums caused by broken trunnion bolts. This fastener secures the trunnion assembly to prevent water leaks and vibration.
The seal at the bottom of the tub had started to fail. On large loads water would leak so I ordered a new one rubber seal. Getting the trunnion off the transmission shaft was hard as it was calcified and corroded. I used a wire brush to get some of it off and then used a lot of WD-40. The bolt holding the trunnion plate on sheared off when I tried to remove it on one side and the other came out ok (the bolt hole through the trunnion is not threaded so it should slide out once the plate is off... Read more
Securing nut for ovens and ranges. Holds interior components like convection fans in place. Replace if stripped, damaged, or missing during repair.
Everything was straight forward and easy to repair, I had an appliance tech come out and troubleshoot the repair and watched what he did and asked questions. I then ordered the parts from here and did the repairs myself and saved on having the tech make another trip out. Read more
Washer won't start, stops mid-cycle, or shows error codes? The control board manages all functions. Moderate DIY repair restores full operation.
Hi, it's me again. So I learned a valuable appliance repair lesson when trying to fix this washing machine: don't fix something until you figure out why it broke in the first place! The first speed control board died (fixed with my last story on year) and I assumed it was just a cheap part of something, but I was in fact proved wrong when, to my dismay, the new board died a week or so later. Being the self-appointed washing machine expert I became after the last repair, I got right into the... Read more
Replacement suspension spring for washer tub support systems. Restores proper tension when original spring is weakened, broken, or causing tub tilt.
Watched a few of your videos and ordered the springs and a insert, and actually got the parts right. I am not a Appliance repair guy but I am retired and I am pretty handy so I thought what the heck. I watched the videos, a lot of common sense, common tools, and plenty of time. My knuckles are busted up and a little blood, but I got it done. Was actually kind of rewarding. Works like a champ. The Videos, ARE AWESOME. Read more
Hex head screw secures refrigerator door hinges to the cabinet. Replace if missing, stripped, or lost during moves or repairs. 1/4-20 thread size.
My 10 year old frig door was hanging down to the point it wasnt fully closing and sealing unless you picked up on it. I ordered a lower hinge bracket, upper and lower bearing, and spacer. My bracket was bent down a little due to my kids hanging on the door when looking at the bottom shelf and i discovered my bracket was held on by only two bolts when there was supposed to be three. I ordered a bolt too. I was able to remove the bottom hinge, remove door to replace upper and lower bearing and... Read more
Fix E32 error codes or washer stopping during fill with this water level pressure switch. Senses water level and controls fill cycles. DIY-friendly repair.
The E32 diagnostic code that the Frigidaire washer was throwing after a quick water fill attempt was not in the supplied Data Sheet that came with the washer and Frigidaire would not provide and updated Data Sheet because, "it's a liabiliity issue" was their statement, but they did tell me that the problem was in the Fill Pressure Sensor/Wire Harness or the Main Control Board (the display board). I ordered the Pressure Sensor and Main Control Board from AppliancePartsPros after checking... Read more
Sits on the center hinge pin to maintain proper door spacing and smooth pivoting. Replace if worn, cracked, or missing to restore even door alignment.
Seals the dryer's lint housing to the cabinet, preventing air leaks and maintaining proper airflow. Replace if worn to restore drying efficiency.
Old, unused stack set. Washer was great, dryer was grinding. Started with the mounting bracket/bearing and the belt. The old ones were slightly beatup. Put it back together and the problem persisted. Found the real problem when I pulled apart the blower to get to the motor. The fan had broken fins that had jammed in the side of the blower housing, and the friction had melted through the outer wall of the fan. Got the blower housing from APP, got the fan from a competitors for $30 less. When it... Read more
Dryer overheating or taking too long to dry? This control thermostat regulates internal temperature by cycling the heater on and off. Easy replacement.
I replaced both thermostats, the seals and the heating element and the belt. It's an easy job to keep my dryer last longer. Read more
Outer door glass panel for electric ranges. Replaces cracked, chipped, or shattered glass. Restores visibility and protects internal components.
Ordered new one. Read more
Fix a washer that won't start, stops mid-cycle, or leaves clothes wet. This electronic control board restores proper operation and reliable cycles.
Small spacer that fits on the idler assembly shaft to properly align the belt tensioner. Replace if worn, cracked, or missing to maintain proper spacing.
Reviewed items that might be the issue and ordered them. After installed noise was gone. Read more
Replace a broken, worn, or missing leveling leg on your range. This adjustable foot installs at the base corner to stabilize and level your appliance.
Bolt replaced. Read more
Black graphic overlay that adheres to your range control panel. Replaces worn, bubbled, or damaged film to restore clear button labels and a clean look.
I read that the controller and probe controlled the oven temperature. Also read if replacing controller you should replace the overlay. So I ordered all three parts and installed myself with no problem. I took a photo with my phone prior to unplugging wires so I knew the right way to plug the wires into the new controller. Works like new. Only need a nut driver and screwdriver to repair. Job from star to finish approximately 30 minutes. Read more