Mgrh752bdw Maytag Range Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Little to no heat when broiling
• Gas igniter glows, but will not light
• Gas smell
• Little to no heat when baking

I used the little video clip shown under the part and replaced it myself. Read more

• Oven is too hot
• Little to no heat when baking
• Won't start
• Oven not heating evenly

Online videos made this seem an easy fix. I unplugged the oven and removed the rear panel, then found where the temp sensor entered the oven. I unplugged the sensor's electric connector. Unlike the videos, this sensor screwed in from the inside of the oven, so I had to remove the 2 screws inside the oven which hold the sensor in place. Then I pulled the sensor out, careful not to tear the insulation with the wires and connector. Then I just pushed the new connector through the same hole and... Read more

• Door won't close
• Oven not heating evenly

First of all Appliance Parts Pros is the best!! I would not have had the confidence to make this repair myself without their outstanding videos and Q&A sections on their website. And their prices for parts are very competitive. Like many stories on the website, my oven would heat up beyond the temperature set point. When it reached the target temperature, the lower heating element (I think this is the “bake” element) would shutoff, but the top element (“broil” element I believe) would remain on... Read more

• Gas igniter glows, but will not light
• Won't start
• Element will not heat

After many years of excellent service the burner I use most often on the top of my JenAir range rusted through. After trying to remove the burner, which was firmly rusted into place, I decided to replace the cooktop pan, both burners and igniters. It was an easy repair to swap out the new parts for the old, and the only tool necessary was a #2 phillips screw driver. The only difficulty was that although the cooktop pan appears symmetrical, the screw hole pattern on each side is different. I did... Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

DIY. The delivery to Milwaukee took two days. The project was very easy and took about 1hr. The only tools required were a screw driver (electric) and a pliers. Just make sure your irganized with the screws so you don't lose any or mix up which ones go back in which holes. There's about 20 total screws. This $50 part saved me from having to buy my wife a $1000+ oven. Read more

Appliances will be sold with the house so the old oven racks were no longer shiny. Replacement racks present a better looking oven. Read more

Start by removing the frame on the sides and bottom of the door. (Do not unscrew the corner screw holding the side frame and bottom together.) Be careful the glass will fall once the last screw is removed from the bottom so hold tight. Carefully remove glass and set aside. Remove top frame that held the handle. Once all the frame work and outer glass is removed unscrew the bracket that held the door handle from the door. Taking the top frame and bracket insert screw and washer and screw the... Read more

One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more

Removed oven door by simply lifting it off of the hinges. New models of most stoves have two screws easily accessible from inside the oven door, but this older stove required the entire inner part of the oven door to be disassembled and the interior glass removed before the two screws that attach the handle can be accessed. Make sure to note how the door comes apart because it can be quite puzzling to put the door back together, especially for someone inexperienced with this repair, Read more

The problem was partly caused because the original legs were at full extension. The replacement legs were longer than the originals and were more secure at the needed length. One difficulty was that the threaded base plate where the legs screwed in had been damaged and had to be reshaped, I was able to reshape the sockets with some effort, to allow the legs to thread in, though one remained slightly angled. (A metal tool of some type which could be threaded in and used to bend the socket area... Read more

I ordered the brioler pan for my new stove from y'all it was a little small but that's the part number in the book that I got with the stoveyall did a great job fast shipping just what I ordered will by from again thanks Read more

• Door won't open or close

I replaced the hinge due to the hinge spring breaking. To replace the hinge you do the following: 1. Disconnect power to stove, either at circuit box or at outlet. 2. Lift door off of outside hinge arms ; no screws are used to attach the door to the hinge 3. Remove two screw on under side of cook top, one on each side. 4. Disconnect cook top connector. 5. Lift cook top off 6. Remove screws from top rail of stove that hold the side panel. 7. Remove the screw on the back that hold the side... Read more

These are very easy to replace ,just gave the old one a quarter turn lifted it out took the two wires off (noted where each one will go on the new burner ) pop the wires onto the new burner put it on and good to go. Read more

SIMPLY followed the U-2 video posted at Appliance Parts Pros. It was so easy and probably saved us a couple hundred dollars (in parts mark-up and labor) compared to hiring it out. It was a 10 minute job and it was done. Jeff PS. I ordered the part Sunday PM and received the part Tuesday morning...THANKS! Read more