Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Agitator barely moving clothes? Worn agitator dogs prevent the ratcheting action needed for proper washing. Simple DIY fix in under 30 minutes.
I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more
Washer won't spin or agitate? A broken motor coupling disconnects the motor from the transmission. DIY repair in 30-45 minutes with basic tools.
My whirlpool washer was no longer spinning, so my first stop was YouTube where I found the video from AppliancePartsPros showing how to replace the motor coupling. In addition to the replacement guide, Matt also shows you how to diagnose the problem by looking for rubber shavings under the washer. Seeing the rubber shavings under the washer, combined with the fact that the washer still drained meant that the motor was still working, so something else in the drive train was bad. I took the... Read more
Washer won't spin or leaves clothes soaking wet? A worn clutch assembly prevents the tub from spinning properly. Moderate DIY repair with video guide.
A couple of years ago, I had an issue with my Whirlpool washer which is every bit of 18 years old. I checked the internet for what might be wrong and stumbled across some how to videos on how to fix it. So, the other day, when my washer quit spinning the first thing I did is go to the internet again to see if I would be able to fix again. Thank you, Appliance Part pro.com, for your very helpful website with the very informative video's on how to replace parts! After I watched a... Read more
Washer leaking water underneath or not draining? This drain pump removes water during the cycle. DIY repair typically takes 10-15 minutes with basic tools.
With much trepidation, I Googled leaking washing machines and deduced that our problem was likely (but not certain) that we needed to replace the direct drive washer pump. After viewing the AppliancePartsPros video, I decided that ordering the $30 part was worth the risk (vs a $120 plus service call). The pump arrived w/in 2 days and my wife and I experienced an enjoyable bonding experience installing it :). But it's now working great and there is no leak. ... Kudos to AppliancePartsPros for a... Read more
Fix a washer agitator that won't turn or makes grinding noises. This medium cam repair kit includes dogs, cam, and seals. Easy 20-30 minute DIY repair.
Replacement suspension spring for washers. Supports and stabilizes the tub during wash and spin cycles. Replace if broken, stretched, or detached.
When I removed the cabinet, all of the springs appeared in tact, I had already replaced the counter balance spring so I knew that was not the issue. None of the suspension springs or brackets were broken but they did look worn/rusty so I replaced all of the brackets (2 in front and 1 large in back), all of the suspension spring retainers, and all of the suspension springs and it fixed the issue! I plan to also replace the Self leveling leg spring which is an easy fix since it's on the back of... Read more
Washer won't fill or drips water after cycle? The water inlet valve controls hot and cold water flow. DIY-friendly repair with video guide included.
I watched the how-to video on your website to learn how to get at the valve to replace it. Before watching the video, I did not know how to take the washer cabinet apart to replace the valve. I searched on your website for my washer model, but the exact model number was not listed. I chose a very similar model number and looked up the info for that machine's replacement valve . It looked like it would work in my washing machine so I decided to take a chance and order the valve. I placed my... Read more
Suspension spring that supports and stabilizes the washer tub during operation. Replace if broken, worn, or missing to prevent tub lean or imbalance.
Agitator not working or spinning loosely? This washer agitator bolt secures the agitator assembly. Simple DIY fix in under 20 minutes with basic tools.
I had replaced the Agitator cams a couple of times already due to my brother-in-law overloading the machine which stripped the teeth off of the cams. I also noticed the agitator seemed to 'wobble' and made 'knocking' noises quite a bit. I reviewed the video on the Appliance Parts Pros web site, disassembled the agitator and cleaned everything up, which helped a little, but not enough. Figuring the agitator itself was worn out also, I looked up and ordered all the parts for the upper agitator on... Read more
Seals the center post/agitator shaft to prevent water leaks during wash cycles. Replace if you notice pooling water under your washer. Confirm fit with your model.
Washer won't spin or agitate? A worn drive block often causes spinning failure. This connects the transmission to the tub. Moderately difficult repair.
Replaced washer drive block and Cam. I called around and finally settled on Appliance Parts Pros because they helped diagnose the problem, told me what parts to replace and had videos to show me how to do it. In completing the repair I had to remove quite a few pieces of hardware in order to get at the part I was to replace. The videos helped but there is a learning curve while you familiarize yourself with the parts and figure out how the remove them. Eventually I got to a large nut that,... Read more
Replacement tub suspension pads for washing machines. Install under the tub to cushion and stabilize during spin cycles. Replace if cracked or missing.
First went through the troubleshooting guide on the website and read the various stories and watched the repair videos for replacing the springs and suspension pads. Then before ordering any parts disassembled the machine only to the point of removing the cabinet to see if there were any obvious issues. The springs appeared OK but I couldn't tell of they were fatigued or not and all were in place but the tub suspension pads were definitely worn out. I then put the machine back together and went... Read more
Fix a washer that won't spin or agitate with a new transmission. Common symptoms include loud clunking noises or clothes staying wet after cycles.
Using appliancepartspros.com site took washer apart to diagnose bad clutch. The clutch was bad but once inside I noticed grease everywhere and after a quick online chat with rep. determined gear case was leaking and needed replacement. Replaced clutch & gear case. Followed video tutorial and took a little more than 30 minutes start to finish for me - I have no experience. The most difficult part for me was actually just getting the retainer ring (little wire) to secure clutch in place-took... Read more
Fix an agitator that won't turn or leaks fabric softener with this inner cap. Simple 5-minute repair—remove the outer cap and replace. Video guide included.
Washer won't start or stops mid-cycle when door opens? The door switch detects door position for safe operation. DIY repair in 10-20 minutes with video.
The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more
Washer won't spin or agitate? A faulty direct drive motor often causes spinning failure and burning smells. Moderate DIY repair in under 2 hours.
All's well that ends well, but the getting there was a bit of a pain. The web site suggests 3 possible causes for my problem (incl. the burning smell). I began with the first two since they were inexpensive compared to the motor, which was the third cause (and also the least often cause). There is no way to visibly tell if the motor is bad or not. After replacing the clutch assembly, which did have some plastic pins broken off) and the motor coupling (which actually looked fine, but the... Read more