Cfw8000gw Parts

This metric machine screw features an M5 x 0.8 thread used to secure panels and assemblies inside your appliance. Replacing missing or damaged hardware restores a tight, rattle-free fit and helps maintain proper alignment of parts.

• Fastens appliance components using an M5 x 0.8 machine-thread
• Replaces missing, loose, or stripped screws
• Helps reduce vibration and rattling noises
• Maintains correct alignment of brackets, panels, or internal assemblies

• Disconnect power before servicing; if working near water connections, shut off the supply.
• Match thread and length to the original screw and replace in the same location.
• Start threading by hand to avoid cross-threading; use the correct driver and do not overtighten.
• Reinstall any original washers or lock hardware used with the screw.

This replacement water inlet valve regulates water flow from the household supply into the washer. It restores proper filling and rinsing when the original valve leaks, sticks, or fails to open.

• Opens and closes to control water entering the dispenser/tub as directed by the control
• Helps maintain correct fill levels and flow during wash and rinse cycles
• Typical symptoms: no fill, slow fill, leaking at the valve, or water continuing to fill when off
• Often required when valve coils test open/short or mineral buildup causes the valve to stick

• Disconnect power and turn off both water supplies before servicing
• Place towels to catch water; relieve line pressure and label hoses/connectors for reassembly
• Transfer any mounting hardware from the old valve if needed; do not overtighten fittings
• Restore water and power, then run a fill cycle and check all connections for leaks

The Control Board is an OEM part for Frigidaire washing machines. This part manages the various functions of the washer, such as filling, agitating, rinsing, and spinning. 

Causes of a bad control board can include power surges, moisture exposure, and general wear and tear over time. Electrical issues within the household or improper use of the washing machine can also lead to damage.

Symptoms of a bad Control Board include:

• The washer not starting or stopping mid-cycle
• Error codes appearing on the display
• Inability to select or change wash cycles
• The washer performing erratically or not responding to controls

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This drum baffle (vane) mounts inside the dryer drum to lift and tumble clothes as the drum rotates, improving airflow and drying performance. A damaged or missing baffle can lead to longer dry times and poor tumbling.

• Helps lift and separate laundry for even drying and reduced tangling
• Worn, cracked, or loose baffles can cause thumping, snagging, or extended dry times
• Replacing a broken vane restores proper tumbling action and airflow
• Common fix for rattling inside the drum or items not tumbling well

• Unplug the dryer before servicing
• Remove the drum screw(s) securing the old baffle; retain hardware if reusable
• Align new baffle over drum holes and tighten fasteners securely
• Rotate drum by hand to verify clearance before reassembly and test

This cap is a small protective cover used in select appliances. It helps secure and seal its mating component, preventing leaks, debris intrusion, or loosening during normal operation.

• Maintains a secure seal/cover over the designated fitting or opening
• Helps prevent leaks and contamination in the covered area
• Can resolve issues like minor leaks, loose or missing cap, or rattling noises
• Restores proper fit and finish after the original cap is lost or damaged

• Disconnect power and shut off water or gas supply before servicing
• Note the orientation of the original cap for correct placement
• Hand-tighten only unless the OEM specifies otherwise; do not overtighten
• Inspect the mating surface or threads for damage before reinstalling

This is the siphon insert for the washer dispenser's bleach and softener compartments. It restores proper siphoning so additives empty at the right time and helps reduce standing water or residue in the drawer.

• Creates the siphon action that draws bleach and fabric softener from their cups during the rinse cycle
• Promotes complete dispensing and consistent rinse performance
• Helps minimize leftover liquid and residue buildup in the dispenser
• Typical symptoms include bleach or softener remaining after the cycle, standing water in the cups, or weak/irregular dispensing

• Disconnect power and turn off water before servicing
• Remove the dispenser drawer; lift out the old siphon from the bleach/softener cup
• Clean any debris in the cup; firmly seat the new siphon, aligned per the cup markings
• Reinstall the drawer and run a rinse cycle to verify proper draw and no leaks

The Outside Door Panel replaces a cracked or broken outer trim on your washer door. It restores appearance and alignment, supporting the door glass and handle so the door latches correctly and cycles can start.

• Forms the exterior frame/trim and handle area of the washer door
• Supports and positions the door glass while aligning with the hinge and latch
• Helps ensure the door closes properly to allow a cycle to begin
• Typical symptoms: cracked/broken trim, loose or misaligned door, difficulty opening/closing

• Disconnect power; turn off water supplies before servicing
• Open the door and support the assembly; remove perimeter screws securing the outer to the inner door panel
• Transfer door glass, handle components, and any reusable hardware from the old panel to the new one
• Reassemble and tighten screws evenly; verify smooth operation and proper latching before use

This drain hose carries wastewater from the washer's drain pump to your home standpipe or sink, ensuring proper draining and helping prevent leaks or backflow. Replace a cracked, kinked, or clogged hose to restore reliable draining.

• Provides a sealed path for wastewater from the drain pump to the household drain
• A damaged or clogged hose can cause leaks, slow draining, or drain-related error codes
• Kinks, splits, or pinholes may allow water to escape during drain cycles
• Loose or worn hose ends can lead to drips at the pump or rear connection

• Disconnect power and water supply; pull the appliance forward to access the hose
• Expect residual water—use towels or a shallow pan and clamp off the old hose if needed
• Note hose routing and clamp locations; reuse existing clamps and secure connections firmly
• Route the new hose without kinks and set the discharge height per your installation guide to prevent siphoning

This component is a drive motor that is made specifically for washing machines. The drive motor is what spins the tub and drives the agitator.If the washing machine fails to start or makes strange noises, it could be the drive motor that is causing the issue. Other signs that this part is faulty are if the washing machine fails to fill with water, agitate, spin, or drain. An error code reading “E57”, “E58”, “E59”, or “srv cll” may also appear on the digital display. Make sure to disconnect the appliance from its power source prior to attempting to replace this part. Whoever is performing the replacement may choose to wear gloves to protect their hands during this process.This drive motor is compatible with washing machines that are manufactured by Whirlpool, Kenmore Elite, Electrolux, Frigidaire, Crosley, and Kenmore. It is sold individually and sourced from the manufacturer itself.

This replacement sealing gasket restores a tight, reliable seal between mating parts in your appliance. A proper seal helps prevent leaks and bypass, reduces noise, and supports overall performance and efficiency.

• Creates a compressible seal between components to prevent air or moisture bypass
• Helps maintain correct airflow/temperature containment for proper operation
• Reduces vibration and rattling caused by hardened or damaged seals
• Replace if the original is torn, flattened, brittle, missing, or leaking

• Disconnect power before servicing; shut off water supply if applicable
• Remove the old gasket and clean mating surfaces of residue/debris
• Match the original routing/orientation; do not stretch or over-compress the gasket
• Tighten fasteners evenly to ensure a uniform seal; verify no pinching or gaps

The Temperature Sensor is an OEM part for Whirlpool washing machines. Situated within the washer tub, the temperature sensor works closely with the control module to monitor water temperatures during all cycles. It provides vital temperature readings that allow the washer to heat water properly according to cycle settings.

Causes can be normal wear over time, impact damage or cracks in the fragile sensor head. Without this crucial component providing accurate temperature feedback, the washer lacks temperature regulation ability.

Symptoms of a failed temperature sensor include:

• Inability to heat water or inconsistent heating
• Error codes or failure to advance cycles
• Functioning only on cold water cycles
• Fluctuating or inaccurate temperature readings

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: Control may no longer include the housing.

This clamp secures a hose to its fitting, maintaining a tight, leak-resistant seal at the connection. Replace a fatigued or missing clamp to help prevent drips and stop hoses from working loose under vibration.

• Holds a hose firmly on a pump, tub, dispenser, or valve outlet
• Maintains clamping force to help minimize leaks at the joint
• Helps keep hoses from slipping off during operation
• Common signs: water at a hose joint, loose/slipping hose, damaged or corroded clamp

• Disconnect power and shut off water supply before servicing
• Place a towel or pan to catch residual water at the connection
• Note hose position; remove the old clamp, seat hose fully on the fitting, position the new clamp over the bead, and secure
• After reassembly, run a short cycle and check for leaks

This door switch detects whether the appliance door is open or closed. A working switch lets the machine start when the door is fully shut and stops operation when the door opens for safety.

• Monitors door position and allows the cycle to run only when closed
• Interrupts power to stop operation when the door opens
• Common symptoms of a failing switch: appliance won't start with the door closed, must press/hold the door to run, interior light stuck on/off, or a "door open" message on models with a display

• Disconnect power to the appliance before servicing
• Access the switch at the door opening/front panel; release mounting screws or locking tabs and remove the switch
• Move wires to the new switch one at a time to maintain correct positions
• After reassembly, test switch operation before running a cycle

This electronic control board manages your appliance's core functions and timing. Replacing a failed board restores proper operation when controls are unresponsive or cycles won't run as designed. What it does

• Distributes power to key components and executes programmed cycles
• Monitors inputs from switches/sensors and controls motors, valves, and heaters as needed
• Can resolve symptoms such as no power to controls, won't start, or cycles not advancing
• Address intermittent operation, error codes/abnormal beeps, or unexpected shutdowns

• 1 electronic control board

• Disconnect power before servicing; verify no voltage is present
• Use ESD precautions and handle the board by the edges only
• Photograph/label wiring and move connectors one at a time to the new board
• Ensure all connectors are fully seated and the board is mounted securely before test

This replacement screw secures appliance components and panels so they stay aligned and rattle-free during operation. Replace stripped, missing, or corroded hardware to restore a tight fit and dependable performance. What it does

• Fastens brackets, panels, and internal sub-assemblies in the appliance
• Helps maintain alignment to reduce vibration and rattling
• Replaces missing, rusted, or stripped screws that no longer hold
• Useful when a part won't mount securely or a screw backs out during use

• One screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Compare to the original for length and thread style for the location
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Do not overtighten; if the mounting hole or clip is worn, replace it