Dlg 2702V Parts

This replacement igniter lights the gas burner in your range or wall oven, restoring reliable starts and consistent heat. Swap in a fresh igniter to resolve hard-to-light burners and no-heat situations so cooking cycles begin as they should. What it does:

• Provides the ignition source to light the bake or broil burner flame
• Helps ensure fast, consistent burner light-off at the start of a heat cycle
• Common symptoms of failure: no ignition/no heat, delayed or intermittent ignition, repeated clicking without flame, or a gas odor before light-off

• 1 igniter assembly

• Disconnect power and shut off the gas supply before servicing; allow the appliance to cool completely
• Note wire connections and mounting orientation from the original part for correct reassembly
• Handle the ceramic/element carefully to avoid damage
• After installation, restore gas and power, then check for leaks with a soap solution

This motor pulley transfers power from the drive motor to the washer belts. The 60 Hz sizing restores the correct speed and belt tracking so the tub agitates and spins smoothly without squeal or slippage. What it does:

• Drives the belt(s) that power the washer's drive system (and on some models, the drain pump)
• Maintains the correct speed ratio for 60 Hz operation
• Worn or damaged pulley can cause belt squeal, burning rubber odor, or frayed/slipping belts
• Result in no/slow spin or agitation if the belt can't grip properly

• One motor pulley (60 Hz)

• Disconnect power before servicing; wear cut-resistant gloves
• Access the motor, relieve belt tension, and note belt routing
• Loosen the pulley set screw and remove the old pulley from the motor shaft
• Install and align the new pulley; adjust belt alignment/tension per service information, hand-rotate to check clearance, then test

• Designed for 60 Hz electrical systems; match the Hz rating to your original part

This drying rack sits inside the dryer drum to hold items that shouldn't tumble. It keeps shoes, sweaters, and other delicates stationary so they dry gently using the dryer's airflow and heat.

• Provides a stationary platform in the drum for rack-dry items
• Helps dry shoes, hats, sweaters, and stuffed toys without tumbling
• Replace if the rack is cracked, warped, missing, or won't stay seated
• Enables use of the rack-dry feature on compatible models

• Disconnect power and let the dryer cool before installation
• Open the door and slide the rack into the designated guides until fully seated and level
• Place items flat on the rack; avoid overloading or letting items hang over the edges
• Remove the rack before running regular tumble cycles

This door gasket seals the dryer door opening to keep heat and moisture inside the drum. Replacing a worn gasket helps restore proper airflow and drying performance while reducing lint and warm air leaking around the door.

• Creates a tight seal between the door and front panel to prevent air leaks
• Helps maintain correct airflow for efficient, consistent drying
• Reduces escaping heat and humidity around the door area
• Common signs it's failing: visible wear or tears, flattened/compressed gasket, lint accumulation near the door, longer dry times, warm air leaking when the door is closed

• Disconnect power; for gas dryers, also shut off the gas supply
• Remove the door assembly as needed and separate door panels to access the gasket (procedure varies by model)
• Remove the old gasket and clean the mating groove/surface of residue and debris
• Press the new gasket fully and evenly into place; align the seam, reassemble the door, and verify an even seal

This drying rack sits inside the dryer drum to hold items stationary while warm air circulates around them. It lets you rack-dry shoes and delicates without tumbling, helping prevent banging and scuffing that can happen when items rotate. What it does:

• Provides a stable platform inside the drum for stationary drying
• Allows heated air to circulate around items while preventing tumbling
• Used for shoes, sweaters, hats, and other items approved for rack-dry cycles
• If missing or damaged (cracked frame, broken tabs, poor seating), you may hear rattling or be unable to rack-dry items

• 1 drying rack

• Disconnect power and allow the drum to cool before inserting or removing the rack
• Insert the rear of the rack into the drum supports, then rest the front edge on the door opening; ensure it is level and fully seated
• Load items evenly and do not overload; use the rack-dry or low-heat settings recommended in your owner's manual
• Remove the rack before resuming standard tumble cycles

10 - 16 x 1/2

This cycling thermostat regulates your dryer's internal air temperature by switching the heat source on and off, helping prevent overheating and keeping drying performance consistent. Replace it if temperatures are erratic, items run too hot, or dry times increase. What it does:

• Monitors drum air temperature and opens/closes to control the heater
• Maintains stable temperatures across fabric/temperature settings
• Failure symptoms include no or low heat, overheating/scorch smells, long dry times, or inconsistent cycling
• Helps protect against damage from excessive heat when functioning correctly

• 1 cycling thermostat

• Disconnect power; if it's a gas dryer, also shut off the gas supply
• Allow the unit to cool; access the thermostat (typically on an internal air duct or blower housing); note wire positions
• Transfer wires to the new thermostat one at a time; mount flush against the metal surface; do not overtighten
• After installation, clean lint passages and ensure proper airflow and temperature control

This spring fastener applies constant tension to hold a component securely in place inside your appliance, helping prevent looseness, vibration, or gaps. Replacing a fatigued or missing clip restores a tight, reliable fit.

• Provides spring tension to clamp and retain a part, seal, or panel
• Helps maintain alignment and reduce vibration or rattling
• Restores secure attachment when the original clip is bent, stretched, or missing
• Symptoms can include a part not staying put, visible looseness, or a clip that's damaged or gone

• Disconnect power; turn off water supply if applicable
• Use needle-nose pliers or a suitable spring tool; wear gloves and eye protection
• Note the original orientation before removal to ensure proper reinstallation
• Make sure the mating part or seal is fully seated and the fastener is fully engaged before reassembly

Specs: 10-16 x 1/2 inch.

Kit contains 2 pads, 1 right glide, 1 left glide, and instruction sheet. Support brace no longer included.

For propane order 383EEL3002A.

This part is a motor clamp. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or broken motor clamp on certain makes of indoor appliance models. Motor clamps are essential for properly securing the drive motor on various types of indoor appliances such as washers, dryers, and refrigerators. Without the use of a motor clamp, the drive motor is free to move around or become detached. This can easily cause serious damage to the equipment and prevent proper functionality. Proper tools are needed to replace this part and appropriate safety measures should be adhered to when working on any type of equipment. For accurate information on how and where to install this replacement motor clamp, specific manufacturer diagrams should be referred to.As an authentic replacement part, this motor clamp can be used on multiple different models of washers, dryers, refrigerators, and washer/dryer combos manufactured by Kenmore, Maytag, Whirlpool, and Amana. Please note that this motor clamp is a genuine part made of high-quality materials and is sold individually.

The Cover, Lamp is an OEM part for LG dryers. This component covers and protects the interior lamp inside the dryer, ensuring it stays secure and free from damage while providing illumination inside the drum.

Over time, the lamp cover can become cracked or damaged due to the high temperatures and vibrations within the dryer. It is essential to replace a faulty lamp cover to maintain the proper lighting and protection for the lamp.

Symptoms of a bad lamp cover include:

• The interior lamp not staying in place
• Visible cracks or damage on the cover
• Reduced or blocked light inside the dryer drum
• The cover falling off or becoming loose

This OEM LG part is also compatible with Sears/Kenmore models.

This distortion spring applies the correct tension within the dryer mechanism so parts return to position and operate smoothly. Replacing a fatigued or broken spring helps prevent loose movement, rattling, and inconsistent operation of the related assembly. What it does

• Provides the designed return/tension force for the associated dryer mechanism
• Helps maintain alignment and smooth movement of moving parts
• Can reduce rattling or squeaking caused by weak or missing spring tension
• Symptoms include components not returning to position or intermittent operation

• One distortion spring

• Disconnect power; for gas dryers, also shut off the gas supply
• Allow internal components to cool before service
• Control the spring during removal/installation—springs are under tension and can snap back
• Note the original spring orientation and attachment points to ensure proper reassembly

Right hand side. Used most Admiral, Crosley, Norge, and Magic Chef dryers. Includes glide and felt pad.

This door seal replaces a worn or damaged gasket around the oven door, creating a tight barrier between the door and the front frame. A fresh seal helps the appliance heat efficiently and maintain steady cooking temperatures. What it does:

• Seals the gap between the door and oven frame to minimize heat loss
• Helps the oven preheat faster and hold set temperatures more consistently
• Replace if the gasket is torn, brittle, flattened, or frayed
• Common signs include heat escaping around the door edge and longer cook times

• 1 door seal

• Disconnect power and allow the oven to cool completely before beginning
• Open the door and carefully remove the old seal, noting its routing and attachment points
• Clean the mating surface to remove debris for a proper seal
• Install the new seal evenly without stretching; ensure all ends and anchors are fully seated