Etw 4300 Tqo Parts

This valve controls the flow of household water into the dishwasher during the fill portions of the cycle. Replacing a weak, stuck, or leaking valve restores proper filling and helps prevent fill errors and water damage. What it does:

• Opens and closes to let the correct amount of water into the tub
• Common symptoms: no fill or very slow fill
• Water entering the tub when the dishwasher is off or won't stop filling
• Drips or leaks from the valve body or hose connection

• One water inlet valve assembly

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water; relieve line pressure at the supply
• Note wire and hose orientation before removal; move connections one at a time
• After installation, restore water and power, then run a brief fill to check for leaks

Push-in.

This Agitator Auger is the upper half of a dual-action washer agitator. It works with the agitator cam and dogs to create the screw-like motion that pulls clothes downward; replace if the top agitator slips, cracks, or stops turning.

• Forms the upper agitator that produces the ratcheting, spiral action for proper wash turnover
• Common symptoms include the upper agitator not moving, free-spinning or slipping under load, and visible cracks or stripped splines/fins
• Restores correct clothing movement and agitation performance when the upper section no longer drives

• Disconnect power and water before servicing
• Remove the fabric softener dispenser and inner cap, then unbolt and lift off the agitator to access the auger
• Transfer internal components (cam and agitator dogs) if reusing; inspect for wear during reassembly
• Align splines, seat the auger fully, tighten fasteners securely, and test the agitation function

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

This vacuum break valve (also called a vacuum breaker or anti-siphon valve) prevents dirty water from being drawn back into the supply when flow stops, protecting your water supply and helping maintain proper fill and drain performance.

• Breaks siphon/backflow after fill or drain cycles to prevent contamination
• Helps maintain correct water levels and consistent filling
• Common symptoms of a failed valve: leaks at the valve/hoses, unintended draining or backfilling, intermittent or slow fill, gurgling noises
• Restores the proper water flow path when replaced

• Disconnect power and shut off the water supply before servicing
• Place a towel or tray to catch residual water when removing hoses
• Note hose orientation and transfer existing fittings/clamps as needed
• Restore water/power and run a test cycle; check carefully for leaks

This washer agitator is the central wash-motion component. It mounts to the drive hub and churns laundry through water and detergent, restoring proper turnover when the original agitator is cracked, stripped, or missing.

• Creates the back-and-forth wash action that moves clothes through the wash water
• Restores proper turnover and cleaning when the old agitator is damaged or worn
• Typical symptoms: no or weak agitation, clothes not moving, clicking/ratcheting from the agitator area, or a loose/wobbly agitator
• Visual issues may include cracks, stripped splines, or a unit that lifts off easily

• Disconnect power and shut off water before servicing; wear cut-resistant gloves
• Remove the softener dispenser and cap, then the center bolt/retainer; pull the old agitator straight up
• Align splines and seat the new agitator fully; reuse existing bolt and cap unless damaged
• Do not overtighten the fastener; run a short test cycle to ensure proper agitation

This agitator drive shaft sits inside the washer's gearcase and transfers motion to the agitator. Replacing a worn or stripped shaft restores firm engagement and reliable wash action while helping reduce slip and grinding during agitation.

• Transfers oscillating motion from the transmission to the agitator
• Provides the splined interface that engages the agitator/coupler
• Common symptoms include no agitation, intermittent/slipping agitation, or grinding/clicking from the gearcase
• Visible wear, rounded splines, or a bent shaft can lead to a loose or non-moving agitator

• Disconnect power and water; use proper PPE
• Requires removing the cabinet and gearcase; drain and reseal the gearcase per service procedures
• Keep gears, spacers, and clips in order; reassemble in the original orientation
• Inspect mating parts (agitator coupler/splines, drive block, seals) and replace if worn

Used for lid switch.

This is the central wash-action component in select top-load washers. Replacing a worn or damaged agitator restores proper agitation so clothes circulate through water and detergent for consistent cleaning performance. What it does:

• Converts drive motion into the back-and-forth action that moves laundry
• Circulates clothes to improve soil removal and reduce tangling
• Replaces cracked, stripped, or loose agitators that cause weak or no agitation
• Common symptoms include poor cleaning, clothes not moving during wash, or an agitator that wobbles or spins freely by hand

• 1 agitator assembly

• Disconnect power and turn off water supply before servicing
• Remove the fabric softener dispenser and inner cap to access the center bolt
• Remove the bolt, lift off the old agitator, seat the new agitator on the splined shaft, and secure the bolt
• Reinstall the cap/dispenser; reuse original hardware as applicable and check for a secure fit before testing

This centerpost bearing supports the washer's spin basket on the stationary center post, providing a low-friction surface for smooth, quiet rotation. Replacing a worn bearing helps restore proper spin performance and reduce noise and vibration.

• Supports and centers the spin basket on the tub centerpost/drive shaft
• Provides a low-friction bearing surface to reduce wear and noise
• Helps maintain basket alignment and stability during spin
• When worn, may cause grinding or squealing in spin, excessive vibration or wobble, and poor/slow spin

• Disconnect power and water supply before servicing; use proper PPE
• Access typically requires removing the agitator, inner basket, and related drive components
• Clean mating surfaces; inspect the centerpost/spin tube and tub seal and replace any worn seals per service guidance
• Seat the bearing fully and verify smooth basket rotation before reassembly

This anti-rattle clip adds light spring tension to keep a small component snug and quiet during operation. Replacing a bent or missing clip helps reduce vibration noise and maintains a secure fit of the attached part.

• Applies tension to prevent rattling and buzzing during use
• Helps keep the mounted piece properly seated and aligned
• Common symptoms of failure: audible rattle, loose/wobbly component, missing or deformed clip
• Simple, drop-in replacement where the original clip is used

• Disconnect power to the appliance before servicing
• Note the original clip's orientation; transfer the new clip the same way
• Use needle-nose pliers for placement; avoid over-bending the clip
• The component is secure and clears adjacent parts before reassembly

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This gray control knob replaces a worn or broken knob on the console so you can accurately select settings. It fits onto the timer/selector shaft and restores a secure grip with smooth, positive engagement. What it does:

• Attaches to the control/timer shaft on the front panel
• Lets you turn and select cycles or options
• Restores a snug fit when the original knob is cracked or stripped
• Common symptoms: knob spins freely, falls off, won't turn settings, or is missing

• 1 gray control knob

• Disconnect power before servicing
• Pull the old knob straight off the shaft; retain any insert/clip used by your model
• Align the new knob with the shaft and press firmly until fully seated
• Test all settings for proper engagement

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Contains two, six foot long braided hoses with 90 degree ends.