Frigidaire Ftf2140fs0fs Parts

The Drive Motor is an OEM part for Frigidaire washing machines. This motor powers the drum's rotation during both the wash and spin cycles. It ensures that the drum agitates and spins correctly, allowing for effective cleaning and rinsing of laundry.

Over time, the drive motor can fail due to regular wear and tear, electrical issues, or overloading the washing machine.  

Symptoms of a bad drive motor include:

• The drum not spinning or agitating
• Unusual noises or humming sounds during operation
• The washing machine stopping mid-cycle
• Burning smells coming from the motor area

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This O-Ring creates a tight, leak-resistant seal between appliance components. Replacing a worn or flattened ring restores proper sealing, helps stop drips at the joint, and protects nearby parts from moisture and mineral residue.

• Provides a compression seal between fittings, housings, or tubes
• Helps prevent water leaks and loss of pressure at the connection
• Common signs of failure: moisture or residue around the joint, visible cracks/flattening, leaks after reassembly
• Regular wear, heat, chemicals, or age can harden or deform the ring

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place a towel to catch residual water
• Clean mating surfaces; lightly lubricate the new O-ring with food-grade silicone grease
• Seat evenly without twisting or pinching; reassemble and check for leaks

This is the water inlet valve that controls the flow of household water into your washer during fill and rinse. Replacing a failing valve restores proper filling performance and helps stop unintended water entry when the machine is idle.

• Opens and closes to allow the correct amount of water into the washer as commanded by the control
• Failure can cause no fill, slow/long fill, or continuous filling/fill when off
• Leaks from the valve body or hose connections indicate the valve should be replaced
• Electrical coil failure may lead to intermittent or no operation

• Disconnect power and shut off the water supply before servicing
• Place a towel or pan to catch residual water; label and disconnect hoses and wiring
• Install the new valve; transfer any brackets or clips from the old part if needed
• Restore water and power, then check all connections for leaks and run a test fill

Note: Control may no longer include the housing.

This clamp secures a hose to its fitting, maintaining a tight, leak-resistant seal at the connection. Replace a fatigued or missing clamp to help prevent drips and stop hoses from working loose under vibration.

• Holds a hose firmly on a pump, tub, dispenser, or valve outlet
• Maintains clamping force to help minimize leaks at the joint
• Helps keep hoses from slipping off during operation
• Common signs: water at a hose joint, loose/slipping hose, damaged or corroded clamp

• Disconnect power and shut off water supply before servicing
• Place a towel or pan to catch residual water at the connection
• Note hose position; remove the old clamp, seat hose fully on the fitting, position the new clamp over the bead, and secure
• After reassembly, run a short cycle and check for leaks

This shipping bolt kit, also called a shipping support kit, secures the washer's tub and suspension for safe transport. Install before moving or shipping the appliance to help prevent internal movement and damage, then remove before operating. What it does:

• Locks the wash tub in place to reduce movement during transit
• Helps protect against vibration and damage while the unit is moved
• Ideal when relocating or shipping the appliance; replaces lost original shipping hardware
• Not for normal operation—remove all shipping bolts before use

• One shipping bolt kit

• Disconnect power, turn off water, and move the appliance to access the rear.
• Insert bolts into the designated shipping holes and tighten evenly until snug; do not overtighten.
• Follow your model's installation guide for bolt locations and quantity.
• Before first use after transport, remove all shipping bolts and any spacers; save for future moves.

This washer drum baffle mounts inside the tub to lift and tumble laundry during the wash cycle. Replacing a cracked or missing baffle helps prevent snags and restores quiet operation and proper garment turnover.

• Lifts and guides clothes inside the drum to improve wash action and distribution
• Helps reduce tangling and balling of large items during cycles
• Replace if broken, loose, or missing
• Common symptoms: rattling/thumping from the tub, visible damage or missing paddle, clothes snagging/tearing, poor tumbling

• Unplug the appliance and turn off water supplies before servicing; wear cut-resistant gloves
• Access the baffle's retaining screw or locking tabs per your model; rotate the drum to align and remove the old baffle
• Transfer any reusable hardware; seat the new baffle fully and secure it
• Rotate the drum by hand to verify clearance, then run a short test cycle

This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.

• Fastens cabinet panels, brackets, or internal parts in washers and dryers
• Direct replacement for worn or lost screws to keep assemblies aligned and secure
• Helps address loose/vibrating panels, rattling noises, or visible gaps/misalignment
• Spec: #10-16 thread; 0.75-inch length

• Disconnect power; for washers, also shut off water supply
• Match the original screw location; start threads by hand to prevent cross-threading
• Use a driver that fits the screw head properly; tighten snugly without overtightening

This access panel service cover replaces a damaged or missing cover to protect internal components and give technicians safe access for diagnostics and repairs. It restores a finished appearance while preventing dust and debris from entering service areas. What it does:

• Covers and protects internal components, wiring and controls from dust and damage.
• Provides a removable service access point for diagnostics and repairs.
• Common symptoms: cracked, bent, loose or missing panel; exposed components; rattling or drafts near the service area.
• Replacement helps restore safety, reduce drafts and eliminate noise caused by a loose or damaged panel.

• Disconnect power (and water if applicable) before removing or installing the panel.
• Wear gloves to protect hands from sharp sheet-metal edges.
• Reuse existing screws or mounting clips when possible; basic hand tools typically required.

This genuine replacement screw secures appliance components and panels in place to keep your unit assembled and operating smoothly. Use it to replace a missing or damaged fastener so parts stay tight and properly aligned.

• Fastens brackets, panels, or assemblies as designed by the manufacturer
• Helps resolve loose or rattling panels caused by a missing/stripped screw
• Maintains proper alignment after service or repair
• Restores secure mounting when an original fastener is lost or damaged

• Disconnect power (and shut off gas/water if applicable) before servicing
• Use the correct driver to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Replace any damaged clips or inserts the screw threads into

This machine screw secures panels, brackets, and internal components in compatible appliances. Replacing a missing, rusted, or stripped #10-16 x 3/4-inch screw restores a snug fit and helps keep assemblies properly aligned and quiet.

• Fastens panels, brackets, guards, or other hardware in appliance assemblies
• Replaces lost, corroded, or stripped mounting screws
• Helps reduce vibration and rattling from loose fittings
• Maintains proper alignment and secure attachment of components

• Disconnect power before servicing; turn off gas and/or water supply if applicable
• Note original screw locations and any spacers or clips for correct reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• Use the appropriate driver or nut driver; wear gloves and eye protection

This dispenser assembly replaces a worn or damaged refrigerator dispenser to restore reliable dispensing of water and ice. It provides the dispenser housing and interface needed for proper user operation and sealing at the door. What it does:

• Houses the dispenser components and provides the push-lever/door opening for water and ice delivery
• Restores a broken, cracked or loose dispenser opening that causes poor engagement or cosmetic damage
• Helps stop minor leaks or drips at the dispenser area when seals and gaskets are intact
• Eliminates sticking or misaligned dispenser operation that prevents normal dispensing

• Disconnect power and shut off the water supply before beginning any work.
• Installation typically requires removing the refrigerator door panel(s) and detaching the old dispenser from the inner door; keep fasteners for reuse unless replacements are provided.
• Handle plastic parts gently to avoid cracking; inspect door seals and gaskets and replace if worn.
• After installation, restore power and water, then test dispenser operation and check for leaks.

Door hinge that restores proper door alignment and smooth pivoting for your refrigerator. Replacing a worn or bent hinge helps stop door sag, rubbing, and uneven gaps so the door seals and closes reliably. What it does:

• Supports and pivots the refrigerator door to keep it aligned and moving smoothly
• Helps stop door sagging, rubbing, sticking, or uneven gaps around the door
• Reduces door noise and wear by restoring stable pivot action
• Helps maintain a consistent door seal to limit moisture and cold-air loss

• Disconnect power and remove food and loose items from the door before starting work
• Support the door while removing fasteners to prevent dropping or damage
• Compare the new hinge to the old one for orientation before installing; tighten fasteners securely but avoid over-tightening

This air chamber directs refrigerated air from the freezer to the fresh food section to help maintain consistent temperatures and proper airflow. It replaces a cracked or damaged diffuser that can disrupt cooling performance. What it does:

• Channels cold air through the refrigerator compartments for balanced cooling
• Helps prevent temperature imbalance and warm spots in the fresh food area
• Reduces uneven frosting or condensation caused by airflow leaks
• Restores intended airflow path when the original chamber is broken or missing

• Disconnect power to the appliance before starting any repair
• Typically installs behind interior liners; remove shelves and panels as needed for access
• Handle the part and surrounding trim carefully to avoid damaging clips or seals

This is a Phillips pan head machine screw commonly used to secure panels and components in appliances. It provides a reliable, low-profile head for flush fastening and easy Phillips-driver installation. What it does:

• Fastens trim, panels, or internal components where a pan head screw is required
• Designed for secure grip in metal or threaded inserts compatible with #10-16 threads
• Helps prevent loosening from vibration when installed to correct torque
• Often used in refrigeration and major appliance assemblies in limited quantities

• One Phillips pan head screw (#10-16 x 5/8")

• Use the correct #2 Phillips driver and steady pressure to avoid cam-out or stripping
• Do not overtighten; stop when snug to avoid damaging threads or mating parts
• Replace only with an identical thread size and head style to ensure fit
• Wear safety glasses when working around sharp sheet metal and springs

No.8 pan head `10 - 10b x 0.50 `cr/sq drive