Gde21dmkes Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This dryer tumbler seal fits at the front or rear of the drum to close the gap with the bulkhead. It restores proper airflow, reduces friction and noise, and helps prevent clothes from snagging at the drum edge.

• Seals the drum-to-bulkhead gap to maintain correct airflow and drying performance
• Provides a smooth surface that helps reduce squealing, scraping, or thumping noises
• Helps prevent clothing from catching at the drum opening
• When worn, symptoms include longer dry times, increased cabinet lint, or frayed/missing seal material

• Disconnect power; shut off gas supply for gas dryers
• Access the front or rear bulkhead per your model; remove panels/drum as needed
• Remove the old seal and clean mating surfaces thoroughly
• Install the new seal evenly; if your model requires adhesive, follow the service manual; hand-rotate the drum to verify clearances before reassembly

This compressor start device attaches to the compressor to help it start and protect it from overheating. Replacing a failed device can help restore reliable compressor starts and consistent cooling.

• Provides the initial boost to start the compressor, then disengages
• Protects the compressor by opening the circuit on overcurrent/overheat
• Common symptoms of failure: compressor won't start, repeated clicking or buzzing from the rear, warm temperatures, short cycling
• Often shows heat damage or a burnt odor at the connector when failed

• Disconnect power and remove the rear access panel to reach the compressor
• Note wire locations and compressor pin orientation; take a photo before removal
• Push the device straight onto the compressor terminals until fully seated; replace any burnt connectors
• Restore power and verify smooth compressor start without repeated clicking

This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:

• Detects door position and allows operation only when the door is fully closed
• Interrupts operation when the door opens for safety
• Common symptoms include: won't start, stops when the door is moved, or "door open" message/error
• Intermittent starts due to worn actuator or internal switch contacts

• 1 door switch

• Disconnect power before servicing
• Access the switch from the front or top panel; release mounting screws or tabs
• Move wires to the new switch one at a time to maintain correct positions, then secure the switch
• Test operation before reassembly

The Temperature Sensor Grille is an OEM part for GE refrigerators. This grille covers and protects the temperature sensor, ensuring it accurately measures the internal temperature of the refrigerator.  

Causes of a bad grille can include physical damage from impacts, regular wear and tear, or the buildup of dust and debris that can obstruct airflow.  

Symptoms of a bad temperature sensor grille include:

• Inaccurate temperature readings
• The refrigerator running continuously or not cooling properly
• Visible damage or obstruction on the grille
• The sensor becoming loose or dislodged

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This idler spring attaches to the idler arm to keep the drive belt properly tensioned, preventing slip and chatter. Replacing a weak or broken spring restores steady rotation and helps reduce noise and belt wear.

• Maintains correct belt tension by pulling the idler arm into position
• Helps prevent belt slippage, squealing/chirping, and premature belt wear
• A failed spring can cause no or intermittent rotation and the belt coming off
• Typical signs include a loose belt, off-track belt, or rhythmic squeak from the base

• Disconnect power before servicing; if working on a gas appliance, shut off the gas supply
• Access the idler assembly; note belt routing before removal
• Relieve belt tension, then move the idler arm to remove and replace the spring on the same mounting holes
• After reassembly, rotate by hand to verify smooth belt tracking before test

The Ice maker is an OEM component for GE side-by-side refrigerators featuring an internal ice production system. Precisely engineered to harvest cubes and eject them for convenient access, it provides invaluable functionality. A reliable ice supply relies on a functioning ice maker.

Causes of failure often relate to the wearing of plastic gears and rollers over extended use, water damage causing sensor degradation over time, or mineral buildup limiting water and energy delivery.   

Symptoms include:

• Reduced or ceased ice production even when the refrigerator was cooling properly  
• Clumped ice clogs rather than individual cubes dispensing
• Strange noises or vibrations coming from the ice compartment  

Replacing with this genuine GE icemaker restores a workhorse feature through precise component integration and resilient materials selection. Compatible replacements suit Hotpoint, RCA, or Kenmore units.

The Valve & Guard Assembly is an OEM part for GE refrigerators. This component controls water flow into the ice maker and water dispenser systems. It incorporates both inlet and outlet valves along with a filter guard to protect internal components. 

Symptoms of a bad valve assembly include:

• Drips or leaks around the valve area 
• Failure to dispense water through the external dispenser 
• Inability to adequately fill the ice maker when producing cubes

Causes can be mineral buildup over time, worn valve seals, or damage to valve components.

This GE OEM replacement restores the full functionality of the refrigerator's internal plumbing. Its durable valves and protected filter ensure dependable water access and protection from contaminants entering the system. Compatible with later produced Hotpoint, RCA, and Kenmore models.
 

The Ice Bucket is an OEM part for GE freezers. This part is specifically designed to store ice cubes, providing a convenient solution for keeping your drinks cool and refreshing. This ice bucket ensures proper storage and easy access to ice whenever you need it. It is made of high-quality materials that can withstand the freezing temperatures of your freezer and the daily demands of ice storage.

A bad ice bucket can occur due to accidental damage, wear and tear, or other factors. If you notice symptoms such as cracks, leaks, or difficulty in accessing the ice from your current bucket, it may be time to replace it with a new one.

Symptoms of a bad ice bucket include:

• Cracks or damage
• Leaks or drips
• Difficulty accessing ice

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This gasket is a sealing component used in select appliances. It fits between two mating parts to keep water or air where it belongs, helping prevent leaks and ensuring proper performance. What it does:

• Forms a tight seal between components or housings
• Helps prevent water drips, seepage, or air leaks at the joint
• Maintains correct appliance performance by keeping moisture/airflow contained
• Replace if the gasket is cracked, torn, flattened, or misshapen
• Common signs include residue, moisture, or visible gaps around the seal

• 1 gasket

• Disconnect power; turn off the water supply before servicing
• Note the orientation of the old gasket prior to removal
• Clean and dry the mating surfaces; remove any old gasket residue
• Seat the new gasket evenly without stretching; reassemble and check for leaks or proper seal

This dryer timer controls and advances the cycle you select, routing power to the correct components and shutting the dryer off at the proper time. Replacing a worn timer restores consistent cycle timing and end-of-cycle shutoff.

• Controls cycle selection and duration
• Advances the dial through the program and turns the dryer off at the end
• Routes power to dryer components at the correct times during the cycle
• Signs of a failing timer may include: cycle not advancing, running indefinitely, stopping early, or erratic timing

• Disconnect power; for gas dryers, also shut off the gas supply
• Remove the control knob and access the console to unmount the old timer
• Label or photograph wiring; move terminals to the new timer one at a time to avoid miswiring
• Align the timer shaft with the dial, secure the timer, and test operation before reassembly

This spring fastener applies constant tension to hold a component securely in place inside your appliance, helping prevent looseness, vibration, or gaps. Replacing a fatigued or missing clip restores a tight, reliable fit.

• Provides spring tension to clamp and retain a part, seal, or panel
• Helps maintain alignment and reduce vibration or rattling
• Restores secure attachment when the original clip is bent, stretched, or missing
• Symptoms can include a part not staying put, visible looseness, or a clip that's damaged or gone

• Disconnect power; turn off water supply if applicable
• Use needle-nose pliers or a suitable spring tool; wear gloves and eye protection
• Note the original orientation before removal to ensure proper reinstallation
• Make sure the mating part or seal is fully seated and the fastener is fully engaged before reassembly

This shelf support is the small rear rail clip that secures a refrigerator shelf or drawer rail in place. A worn or broken support can let the shelf tilt or drop, making storage unstable.

• Holds the rear of the shelf or rail securely to the cabinet wall
• Helps correct issues like a sagging, tilting, or loose shelf
• Replaces cracked, missing, or deformed supports causing poor fit
• Restores proper alignment so bins and shelves slide/seat correctly

• Unplug refrigerator before service
• Remove the shelf/bin to access the support
• Depress locking tabs and slide the old support out; snap the new one into the cabinet slot
• Ensure it's fully seated before reinstalling the shelf

The Terminal Block is an OEM replacement part for Frigidaire clothes dryers. It is the part the power cord connects to. This kit includes 3 screws and 3 terminals.

Causes of a bad terminal block can include damage from age, overheating from worn wires or loose connections, or improper installation during manufacturing.

Symptoms of a bad terminal block include:

• The dryer not powering on
• Intermittent heating issues
• Loose, frayed, or damaged wires

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Tube Lead is an OEM part for GE refrigerators. It is responsible for routing water through the unit.

Causes of a bad tube lead can include mineral accumulation restricting flow, loosened compression fittings, or cracked/split tubing exposing water to air.

Symptoms of an issue with the water line tube lead include:

• Slow or inconsistent water and ice production
• Water pressure or temperature fluctuations at the dispenser
• Leaks in the refrigerator's exterior bottom panel

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.