Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Dryer shuts off too soon or won't heat? A faulty high limit thermostat often causes premature shutoff. Simple DIY fix—usually takes 15 minutes or less.
Changed out high limit thernasstat Read more
Fix a dryer that won't heat or takes forever to dry clothes. This heating element assembly restores proper drying. Video guide included.
Found a video on UTube on how to dissamble the dryer. It was striaght forward and helpful. In the process I found an unusal amount of lint in the pipe from the dryer to the vent pipe to the outside It was nearly blocked about 10" up the pipe.. Read more
Dryer door won't stay closed? A worn or broken door strike prevents proper latching. Easy 5-minute DIY fix with basic tools. Video guide included.
Replaced door strike and door latch Read more
Seals the drum bearing assembly to prevent air leaks and maintain drying efficiency. Replace when worn, cracked, or if dryer is noisy. Confirm fit with model.
Went ahead and replaced the pulley as well the drum bearing sleeve and O ring, drum belt and the front drum bearing slides. Put the unit back together and she ran like a top! Read more
Dryer door won't stay closed? This door latch secures the door and activates the safety switch. Easy snap-in repair, typically 5-15 minutes.
My GE dryer from the late 80's/early 90's was squealing when it would start up, belt or bearing I was thinking. I found a manual online that covered my model and I watched a video on this site that showed me how to take it all apart, mine was a bit different but the principles were the same. I took it apart and added some quick-disconnects to 2 wires so next time I can take the front panel off easily. When I got to the bearing it looked worn but not bad so I cleaned it and put it back. ... Read more
The bearing retainer secures the drum bearing assembly in your dryer. Replace if cracked, broken, or worn to restore proper structural support.
A few months back I changed out the "Bearing Slides" on the front side of the drum thinking that would stop the annoying squeaking every time we use the dryer. They were very worn and one was missing. But to my dismay it only lessened it by about 10%. After doing a bit more research I discovered the "Rear Shaft Bracket Assembly" also needed replacement. The tip was worn way down and clearly the source of the noise. It was actually a very simple repair except for the fact that the key to the... Read more
Dryer timer knob control for selecting drying cycles. Replace if your original knob is cracked, broken, stripped, or missing from the control panel.
Amazing story of speed & quality! Ordered on Friday 4pm, had parts in hand on 2pm on Sat, finished repair by 4pm ... 24hrs! The repair video was 100% on target. Replaced the rear drum bearing, front slides/glides, and the belt (cheap insurance!). All parts were exactly as described on APP.com. I (and my wife) couldn't be happier with the repair, and the exceptional service of APP! Do not be timid about trying this repair yourself. Take your time and watch the video. Priceless! Recommend... Read more
Fix a dryer timer that won't advance or automatic cycles that stopped working. This timer resistor regulates cycle duration. Easy 15-minute repair.
I Replaced the power resistor. The old resistor had a small burnt spot and tested infinity for resistance.The terminals were too small so I had to make new connector. Any 5000 ohm ceramic filled resistor would have worked also. Read more
Supports smooth dryer drum rotation and reduces friction. Replace if drum squeaks, wobbles, or rotates unevenly. Verify fit with your model number.
Watched a video online Read more
Fix melted plastic or goop marks on clothes with a new dryer heat diffuser. Replaces damaged diffuser that causes staining. DIY repair with 3 screws.
Removed 3 screws which required a torx bit. Used small headless nails to line up the holes and use as a guide for sliding on new diffuser. Put screws in one at a time and tightened down. rotating the drum helped with slight mis-alignement with the screw holes. Read more
Dryer door won't stay closed or pops open during cycle? This mounting plate anchors the door strike for secure latching. Quick DIY fix with video guide.
We ordered a door switch, dryer latch and strike plate. We realized that we only needed to replace the door switch. We watched a few videos and then replaced the switch. We couldn’t find a video for our model but they did give us a pretty good idea about what we needed to do. The hardest part was getting the original door switch out, all of the videos we watched showed us that it would pop out with a little pressure from a flat head screw driver, from the front of the switch. We could not get... Read more
Replaces a broken, cracked, or damaged lint trap duct assembly in your dryer. Directs airflow from the drum to the exhaust vent and houses the lint trap.
Our GE front loader dryer is approximately 10 years old. It started making a loud noise. Before we sank another $600 for a new dryer, I decided to go online to search Youtube videos to try to find out if anyone else had the same problem. I found that a lot of dryers had drum support bearings that wore out and needed to be replaced and a lot of dryers were also having clothes caught up in them. I then found an Appliance Parts Pro video on how to fix this problem and found out what parts... Read more
Dryer not heating or overheating? This safety thermostat (hi-limit L210) cuts power when temps get too high. DIY-friendly, 10-minute install with video.
Replaced the high limit safety thermostat. Ordering was easy, and the part came quickly. The video on the web site was helpful, although I was not able to follow the instructions fully. Unless you have super skinny, long arms, you cannot reach under and around the dryer tub to reach the belt tension arm. I ended up having to remove the side panel of the dryer to remove the belt from the motor. Replacing the thermostat was simple enough. At this point, it seems to have corrected the... Read more
Dryer won't start? A blown fuse is often the culprit. This part restores power to the circuit. Easy DIY fix—test with a multimeter first.
First I check the breaker for the dryer then I check the power cord and the ohms to the power cord when all this things were in working order I then check the ohms to the fuse to the control panel. The fuse had no ohms so I got a pair on needle nose pliers pulled out the fuse and replace it worked just find after that Read more
Replacement drum baffle installs inside your dryer to lift and tumble clothes during drying. Replace if cracked, broken, or mounting holes are stripped out.
I ordered two new baffles and 7 screws. I also ordered 6 large washers. We were running with one baffle held by only 2 of 3 screws. It appears that a repairman in the past had removed the large washers and over time, the screw heads reamed out the hole, causing the baffles to detach and break. In about 15 minutes, I was able to tighten up the existing baffle and add the two new ones. I also added the 6 big washers to help strengthen this to prevent future issues. I no longer have to listen to... Read more
Dryer barely blowing air or taking forever to dry? A worn blower wheel fails to pull air through the drum. This wheel restores airflow for efficient drying.