Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Oven won't heat properly or overheats? A faulty temperature sensor may be the cause. Simple 15-minute DIY repair with basic tools and our video guide.
I have a Whirlpool RBS245PDQ12 wall mount oven. Gathering information from AppliancePartsPros.com resulted in two possibilities: The Thermal Switch or the Control Panel. Talking with Appliance Parts Pros led to testing the Oven Temperature Sensor. It's supposed to test at 1080 Ohms at 70 degrees Fahrenheit. Mine tested at 960 Ohms so I knew it was bad... I found the service manual on the top of the Oven on the left behind the control panel. It has values for testing (Ohms of resistance)... Read more
Broiler not heating or only outer ring works? This broil element provides high heat for even browning. Easy DIY fix—disconnect power and test continuity.
DISCONNECT CIRCUIT BREAKER!!!. Remove oven door. Remove two screws that attach the element to the back of the oven, and two screws that secure element to the oven roof, then remove element. Had to be careful that the four wires don't slip into the back of the oven (difficult) to keep them from falling back as they are very short. Remove and replace element. I should have also detached the temp probe as it gets in the way and is easily broken off its flimsy mounting plate. The hardest part is... Read more
Burned or damaged terminal block causing power loss? This connection point fixes arcing, sparking, and burnt wire issues. DIY repair with basic tools.
I determined the hidden bake element below the oven cavity was not working, because the bottom of the oven was cold during normal use. If you have a built-in microwave + oven combination (mine is KitchenAid Model No. KEMS308SSS05), this is a difficult repair. The engineer who designed this oven should be invited to succeed elsewhere. It is impossible to access the bake element from the inside of the oven, so the How To video associated with this part will not help you. I had to remove the... Read more
Oven not reaching temperature or taking too long to preheat? A failed bake element is often the cause. Moderate DIY repair, 1-2 hours with rear access.
Oven won't heat after self-cleaning? This thermal fuse cuts power when overheating occurs. Common DIY repair takes under 10 minutes with basic tools.
This is for the Whirlpool in-wall double oven GBD307PDS10. No power and the door locked after the shutdown before the self-cleaning cycle was over. I watched some video and this is a known issue the fuses blow during self-cleaning. I opened the door with a 90-degree hook, an easy task. Took doors off (watch video from others), unscrewed from the wall, and made a very small platform. and took the oven out (need two people and take the doors off first. The doors are heavy and you won't lift the... Read more
Dual burner not heating or inner element burned out? This surface element restores both small and large heating zones. DIY-friendly repair in under an hour.
Replaced the Infinite Switch and that solved the problem. Did not need to replace the Surface Element Read more
Seals your oven door to prevent heat loss and maintain cooking temperatures. Replace if worn, cracked, or heat escapes. Confirm fit with your model.
Replacing the Door Gasket is very easy and will take about 2-3 mins per door. Simply remove the Gasket Retainer (1 screw), and pull off the old Gasket. Install the new gasket by simply pushing the gasket clips into the holes where the old clips came out from. Be sure to start gasket at the first hole either side of the Gasket Retainer and work your way around. Reinstall Gasket retainer. The Door Insulation is a very involved repair, and best to follow specific repair manual instructions. Door... Read more
White acrylic spray paint for appliance exterior touch-ups. Restores worn, chipped, or scratched surfaces on refrigerators, ranges, and more. 13 oz can.
Replaced It With New One Read more
Range won't turn on or keeps tripping breaker? Melted or burnt terminal block disrupts power flow. DIY-friendly repair, typically 5-15 minutes to replace.
I was going to just throw my stove out and get a new one until I did some research. I stumbled onto this site and found my broken part watched a quick video thanks to this wonderful site, they convinced me I could do it. I ordered the part on a Saturday night and Tuesday I got my part I was shocked. Took 5 minutes to fix and this site saved me hundreds of dollars on buying a new stove. Would buy again from this site in a heart beat. Thanks appliance parts pros! Read more
Touch-up paint for covering scratches, chips, and minor blemishes on appliance exteriors. Restores appearance and protects surfaces when finish is damaged.
Touch up paint Read more
Replacement door hinge for wall ovens. Supports the oven door for smooth opening and closing. Replace if bent, broken, or door won't stay horizontal.
Oven door would no longer close completely, ordered replacement hinges, 30 minute repair. Read more
Replace your worn, warped, or missing oven rack. This durable rack installs inside your oven cavity to hold cookware and allow proper air circulation.
Contacted Ashlee in the Customer Service Department of AppliancePartsPro and she not only explained the return policy but help ensure that I ordered the correct parts for my Whirlpool oven. She was wonderful and it was truly great customer service. I will continue to do business with this company. Read more
Replaces the inner heat-resistant glass panel in your oven door. Needed when glass is cracked, shattered, or broken during cleaning or use.
Replaced it myself. Read more
Heating element not working? This mounting screw securely fastens the heating element in place. A simple DIY repair that takes about 20 minutes to complete.
We ordered the part and one extra screw(which we didn't end up using). If possible take door off your oven for easy access and have lighting source to see well. Taking part out was easy. Putting back in was more difficult because you have to match up two layers of parts in our oven. The broiler coil and the broiler shield above it. We used small craft clothes pins to keep wires from going behind the built in oven. We used a small diameter screw driver to match up holes before putting... Read more
Replacement mounting screw for securing components and housings in place. Order a new screw if yours is stripped, missing, or damaged during repairs.
One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS! p.s. In doing my research come to find Maytag did little to insulate control panel from oven... Read more
Burner won't heat or stays cold? This surface heating element restores consistent heat distribution. Most DIYers complete this repair in under 30 minutes.
Your on line video pointed out the problem, how to test, and how to replace the element. I ordered the part it came the next day. Wife is very happy. Read more