Kuds30ixss-4 Parts

This fold-down tine pivot for the lower dishrack acts as the hinge and latch for the adjustable tine row. Replacing a worn pivot restores stable loading and allows the tines to flip up or down as designed. What it does:

• Supports and pivots the fold-down tine row on the lower dishrack
• Holds tines in either position to accommodate different dish loads
• Common symptoms: tines won't stay upright, adjustable row detaches, cracked or missing pivot
• Helps prevent dishes from tipping during wash cycles

• Disconnect power and water supply to the dishwasher for safety; remove the lower rack
• Release the old pivot's locking tabs and slide it off the rack/tine row
• Align the new pivot with the rack wires and tine row; snap securely into place
• The tine row pivots smoothly and holds in both positions

This inner door seal forms a moisture barrier between the dishwasher tub and the door assembly, helping keep wash water and steam contained. Replacing a worn seal can stop drips at the door and protect internal components.

• Seals the joint along the inner door to contain wash water and steam
• Helps prevent door-area leaks or drips during cycles
• Blocks moisture from entering the door cavity where electrical parts reside
• Common signs: water at the bottom/sides of the door, damp control area, visible wear/flattening or tears on the seal

• Disconnect power and turn off water supply before servicing
• Open the door and remove perimeter screws to separate inner/outer door panels
• Remove the old seal; clean the mounting surface and note seal orientation
• Press the new seal firmly into place, reassemble, and run a leak check

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

This hose clamp secures dishwasher hoses to fittings and ports to maintain a tight, leak-resistant seal. Replacing a worn clamp helps prevent drips and loose connections that can cause water under the unit.

• Secures drain or circulation hose to the pump, sump, or other dishwasher fittings
• Helps maintain a watertight seal at hose connection points
• Can help resolve water dripping from a hose joint or a loose hose
• Replace if corroded, deformed, cracked, or no longer holds tension

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Fully seat the hose on the fitting, position the clamp over the barb/connection, and secure firmly
• After reassembly, run a brief fill/drain and check all connections for leaks

12 Ft in length

This cover screw secures an appliance cover or access panel to the cabinet, protecting internal components and reducing vibration. Replace missing, stripped, or corroded screws to keep panels tight and the unit safe and quiet.

• Fastens a cover or access panel to the appliance chassis
• Maintains proper panel alignment and enclosure integrity
• Helps eliminate rattles or buzzing from loose panels
• Typical symptoms: loose/misaligned cover, missing screw, vibration noise

• Disconnect power; for gas/water appliances, shut off supplies before service
• Wear cut-resistant gloves—sheet-metal edges can be sharp
• Align the cover and start the screw by hand to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin metal

Color: Black

Includes two screws, two clamps, and undercounter mounting brackets.

This genuine OEM part is a touchpad control panel assembly for dishwashers. The touchpad control panel assembly is the plastic piece that houses the selection buttons of the dishwasher that control the desired setting of the washer. If the touchpad control panel assembly is no longer responsive to touch, it will need to be replaced.To replace this part, start by turning off the power to the appliance. Then take a screwdriver or putty knife to release the control panel from its locking tabs. Pull up gently to pry the control panel out of its place. Once removed set it to the side, and remove the wire harness and any individual wires that are attached to the control panel. Once removed, place the wires into the new unit in their correct terminals. Snap the new control panel assembly into its proper position and restore power to the dishwasher. This authentic replacement part is sourced directly from the manufacturer and is sold individually. It is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand dishwashers.

Color: White

This insulation pad installs in the factory location to isolate and cushion components or panels. It helps reduce vibration and limit unwanted heat transfer, supporting quieter operation and proper performance where the original pad was installed.

• Provides a thermal and acoustic barrier between parts or panels
• Helps minimize vibration and rattling noises
• Restores proper spacing/cushioning when the original pad is missing or deteriorated
• Replace if the pad is brittle, compressed, contaminated, or falling off
• Common signs include increased noise or rattles and localized hot spots or condensation

• Disconnect power (and gas/water, if applicable) before servicing
• Allow hot or cold surfaces to return to a safe temperature
• Note the original pad's location/orientation; remove old pad and clean the surface
• Install the new pad in the same spot without over-compressing; secure per the original method and verify clearances

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

Also Order Spray Arm Seal

This replacement utensil basket holds silverware and small kitchen tools upright in the dishwasher so they stay separated for better cleaning and don't fall through the lower rack. Durable plastic design for everyday use. What it does:

• Holds forks, knives, spoons and small utensils upright and separated for improved wash coverage
• Keeps utensils from falling into the wash area or getting trapped under the rack
• Helps reduce rattling and clumping of cutlery during the cycle
• Useful when the original basket is cracked, broken, or missing

• No tools required; slide or drop the basket into the lower rack in the designated position
• Ensure the lower rack is pulled out enough to seat the basket fully and that it sits flat
• Clean basket with mild detergent; avoid harsh solvents or abrasive pads

This run capacitor helps start and keep the motor running smoothly by providing the necessary phase shift and torque boost. A weak capacitor can cause hard starting, humming, or intermittent motor operation.

• Supplies continuous phase shift to maintain motor rotation
• Helps the motor start reliably under load
• Symptoms can include humming, slow or no start, or overheating shutdown
• Restores normal operation when the original capacitor has weakened

• Disconnect power before servicing; discharge the old capacitor safely
• Note wire locations and transfer leads to the new capacitor one-by-one
• Mount securely in the original bracket or location to prevent vibration
• If the motor still won't start, further diagnosis of the motor or start device may be required