Maytag Lat9557aae Top Load Washer Parts

Removed the old tub cover/gasket by removing the front panel and top lid. Then, unclipped the tub cover. Read more

New parts did the trick. Very easy to replace. Did not need to replace the base agitator, the fabric dispenser, or the screw; but, while it was apart it was simple to do. Read more

Removed lid sanded down all rust spots, taped over the printed instructions on the inside of the lid, washed with alcohol and spray painted with appliance white epoxy paint. Replaced the plastic hinge-balls and one of the lid support/bumper grommet. It was actually easier to install the lid than removing it; used a small amount of grease to hold both balls in place, by holding the lid vertical and placing the left side to the inserted ball and then pushing the right side down. The lid slides... Read more

We watched the video before we purchased the parts for this project. We wanted to make sure exactly what parts we would need. Thanks for having this information available. We purchased the mounting stem repair kit,,tub bearing kit, 3 new bolt/washers that hold the outer tub in place and the spanner wrench. Cleaned everything... NOTE :TAKE THE TIME TO CLEAN YOUR FILTERS ON THE BOTTOM. Thing went back together smoothly. We refereed back to the video when in doubt. Total repair $118.00... Read more

Simple. Remove top back panel. (4 screws) Remove old injector. (1 nut screw.) Rotate to remove. (Other side is a tab in a slot.) Unsnap the upper injector. Snap upper injector on to new lower injector. Replace in reverse order. Run washer, look for leaks. Read more

I emailed appliancepartspros.com with what my problem was and they informed me what was wrong they gave me a part number to order, tools needed and a brief explanation how replace the seal. they also have online video's for different repairs. I watched the video for lip seal(part # 207843) replacement.I also had to remove the brake assembly in order to replace the seal so I watched that video also. I went online and got the part numbers for items I needed to make my repairs.Just follow the... Read more

American appliances are very easy to fix in comparison to imported ones. Just open the washer and take de transmission cover out change the pinion inside removing a simple retainer. In the agitator there is a screw that you loosen it take it out, then de tub and take the shaft out and put a new seal and a new c clamp and reinstall everything back. Top-loading washers are very easy to fix in comparison to front-loading washers that are very difficult to fix. Read more

• Leaking

Here's the story. All my appliances except the dryer broke. Yeah. talk about bad luck. First I tried to fix the refrigerator. Replaced both motherboard and inverter board. Now it wakes up but the compressor does not kick in. Need another part. The washer, well I have to pull out the sink to get enough room to pull out the washer to fix it. Since the refriigerator is still in the middle of the kitchen, I don't need to tear apart another room. Nevertheless, let me say this, I love my "older"... Read more

Here's the story. All my appliances except the dryer broke. Yeah. talk about bad luck. First I tried to fix the refrigerator. Replaced both motherboard and inverter board. Now it wakes up but the compressor does not kick in. Need another part. The washer, well I have to pull out the sink to get enough room to pull out the washer to fix it. Since the refriigerator is still in the middle of the kitchen, I don't need to tear apart another room. Nevertheless, let me say this, I love my "older"... Read more

Purchased and installed new tub bearing and seals. Decided to replace the tub bolts as well, since I had it apart. Now if I could just find a new outer tub (which the manufacturer has discontinued). Appliance parts pros has a great "how to" video which made it simple! Read more

After the timer quit we had one more load to do so we ran each cycle manually, advancing the timer by hand through the pre-soak, wash, rinse, spin cycles. That told us there were no problems with the other switches. Pulled the back off the control assembly and it was no big deal to get the old timer out. I suggest doing that before you order and comparing the part you are replacing to the images shown online (since there are two timer versions for this model) to make sure you get the right... Read more

I emailed appliancepartspros.com with what my problem was and they informed me what was wrong they gave me a part number to order, tools needed and a brief explanation how replace the seal. they also have online video's for different repairs. I watched the video for lip seal(part # 207843) replacement.I also had to remove the brake assembly in order to replace the seal so I watched that video also. I went online and got the part numbers for items I needed to make my repairs.Just follow the... Read more

The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more

Orde red replacement Read more