Need Help?
Call or text
Usually ships within 4 - 14 days
This is a Whirlpool washer control board. This is the main control board behind the user interface, not to be confused with the motor control board located within the body of the washer. This part controls the main functions of the washer and toggles between different cycles. Certain functions may become unavailable intermittently when the main control board loses function. The washer may also continue to spin, not following the regular timeline of the cycle.Start the repair by pulling the control knob from the front of the washer. Pull the washer out from the wall to access the rear panel. Remove the screws from the back panel, and push back on the control panel while sliding a flat head under the right corner to release the mounting clip. Repeat this on the left side, and the central console should pull free. Release the clips for the wire harness and remove the air hose from the control board. Remove the mounting screws and pull the control board from its protective console. Reverse this process to install the new component.This product is a genuine OEM part sourced directly from the manufacturer. This part is compatible with Whirlpool, Maytag, and JennAir appliances.
Replaced wax motor and circuit board Read more
Color: White. For gray order 2206781. Front load washer dispenser lid. If you need the pins to attach the lid order the long pin WP6-912678 and the short pin WPY912679
After much internet research (primary YouTube) as to why my Maytag Neptune washing machine's spin cycle stopped working, I ordered the parts I needed to fix it. Sure enough, it was a failed wax motor and a blown control board at fault. After replacing both parts, we have a functioning washing machine again. While I was at it, I replaced the soap dispenser's bezel and lid since they were deteriorating and now we have a "new" washer! I also replaces the thermostat in the matching dryer and we... Read more
Specs: 10 - 16 x .375
Replaced the Injector valve, nozzle and sleeve-in using new hose clamps Read more
This hinge screw fastens a hinge to the appliance cabinet or door, helping keep the door aligned and operating smoothly. Replace a missing or stripped screw to restore solid hinge support and reliable closure.
Replaced coils on gas valve; while at it replaced door screws which were starting to wear from assorted repairs over the years. Read more
Installed a new water velve but there was still some leakage, discovered that there was three holes in the door boot....will order a new one. Read more
Did not know if these were the right parts. I believe i talked to someone named Robin and she was very helpful and friendly. Said she wasn't sure these were the parts since they were not listed on my model number but said if they didn't work i could send them back. been to many parts stores and nobody could find these two items or even suggest them. Very good employee who helped me. Was really surprised how fast my order got here. Excellent service. I've bookmarked your site and will be doing... Read more
Front load washer door boot seal, comes with drain plug and clamp.
I used the instructions from some of your previous customers. When I was ready to pull the inner tub from the outer tub, it pulled very hard. The front bearing had been HOT and really marked the shaft. The SEAL appeared to be almost plastic, not much left. I removed the seal from the Front bearing. This model had the original type seal with the plastic spacer behind the seal and in front of the front bearing.. BE SURE TO NOTE HOW THE PLASTIC SPACER CAME OUT--feet on spacer toward the... Read more
Busted unit open, found leaks, ordered parts. Cleaned out the mess, put new parts in, works like a champ! Easy as it can get! Read more
Ordered the parts, watched the video and went to work on both. It was all very easy! Read more
This is a Whirlpool washer drive motor and control board. The drive motor and motor control board are responsible for the spin cycles of the washer. A faulty motor may show signs of malfunction through a slower than average spin cycle. When the control board shorts out, the washer typically will not spin at all.Begin installation by removing the body of the washer. There are two screws at the base of the console. Remove these screws and flip the console back. Two clips are holding the body in place. Remove them with a flat-head screwdriver. Push these clips and pull the body off the washer. Now that the motor is exposed, remove the screws holding the motor in place with a nut driver. Two more clips fasten the motor. Push these clips with the flat head, and the motor is free to remove. Unplug the control board's wire harness from the washer. The new component is ready for install after these steps.The part is sourced directly from the manufacturer as a genuine OEM product. This kit is sold separately from the washer. This product is compatible with Whirlpool, Maytag, and Admiral appliances.
I had watched some videos on youtube to understand how to disassemble & gain access to the various washer components & their location. Very easy. I had first replaced the wax motor, but that was not the problem. I reviewed the diagnostic procedures that were present near the control board, followed the directions to remove the main plug from the motor control board, which should allow the washer to spin at 50 rpm. No spin, & upon closer inspection, I observed that one of the phase drive... Read more