Mgd5 Parts

The Natural Gas Regulator is an OEM part for Whirlpool ranges. This regulates the pressure of natural gas entering the appliance, ensuring safe and efficient operation. It maintains a consistent gas flow to the burners and oven, allowing for precise temperature control and optimal cooking performance.

Over time, the natural gas regulator can wear out or become damaged due to exposure to high temperatures, contaminants in the gas supply, or mechanical failures.

Symptoms of a bad natural gas regulator include:

• Inconsistent flame or burner performance
• The oven or burners not igniting or staying lit
• Unusual odors or hissing sounds near the regulator

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Console Clip is an OEM part compatible with Whirlpool dryers. This clip secures the control console assembly to the top panel, ensuring it is firmly mounted during operation. Properly functioning clips are necessary to maintain the correct alignment of controls and prevent detachment. 

Causes of a bad clip can include wear and fatigue from repeated opening and closing of the dryer door. Excessive force or impact could also bend or break the clip over time.

Symptoms of a bad clip include:

• Loose console assembly that is not securely fastened  
• Misaligned or dangling controls that do not sit flush
• Dislodged console at risk of detaching from housing
• Missing clip leaving an open mounting point

This OEM Whirlpool replacement clip is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This sensor wire harness links a sensor (such as a thermistor) to the appliance's control system, ensuring accurate readings and dependable operation. Replacing a damaged or corroded harness restores proper communication and stable performance.

• Carries low-voltage sensor signals between the sensor and main control
• Enables the control to respond correctly to sensor feedback for normal operation
• Typical failure signs: erratic readings, intermittent operation, nuisance sensor/error codes, or visible wire/connector damage
• A damaged harness/connector may be the cause

• Disconnect power before servicing; turn off water supply if moving the appliance requires it
• Access the harness at the sensor/control ends per your model's service information
• Match keyed connectors and seat fully without forcing; do not pull on wires
• Route along the factory path and secure away from sharp, hot, or moving parts

This genuine OEM replacement part is a burner and gas valve assembly for dryers. The burner and gas valve assembly is a complete assembly that contains the burner that distributes the gas in a way that creates an even flame allowing for heat to be distributed properly to perform the dryer's essential function. If the dryer is no longer drying clothes effectively or heating properly, then it might be time for it to be replaced. Luckily repairing a gas valve assembly is a relatively simple job.To replace the burner and gas valve assembly, begin by shutting off power to the appliance. Next, pull the dryer away from the wall to gain access to the back panel. Remove the back panel and locate the burner and gas valve assembly. Remove the mounting screws that hold it in place. After removing the screws use both hands to pull and release the old burner assembly. Set it off to the side and proceed to install the new one by refastening the screws that hold it in place.This replacement part is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand washers.

This support washer is a flat spacer used within the mechanism to support and separate mating parts, maintaining alignment and smoother movement. Replacing a worn washer helps reduce friction and wear so components operate properly. What it does:

• Maintains proper spacing and support between adjoining parts
• Helps prevent metal-to-metal contact, reducing scraping or grinding noises
• Addresses wobble or excess play when the original washer is worn, deformed, or missing
• Restores smoother movement and alignment in the assembly

• One support washer

• Disconnect power and water supply before servicing; for gas combos, also shut off gas
• Refer to your model's parts diagram for location and orientation
• Track the order of any shims/spacers during disassembly and reinstall in the same sequence
• Tighten fasteners to manufacturer guidance to avoid deforming the washer or binding parts

This 3/8-16 nut secures appliance components and helps prevent loosening and vibration. Replace a worn, stripped, or missing nut to restore a tight, reliable connection and consistent operation.

• Provides a 3/8-16 threaded fastener connection for applicable bolts or studs
• Helps keep brackets, panels, and other parts firmly in place
• Replaces damaged or missing hardware that can cause looseness or rattling
• Signs of failure include rounded corners, stripped threads, corrosion, or inability to tighten securely

• Disconnect power and, if applicable, shut off water and gas before servicing
• Match thread size to the original part; start threading by hand to avoid cross-threading
• Reinstall any washers/spacers in the original order; tighten securely without over-tightening
• If the original used a locking feature or threadlocker, reinstall per your product's service information

The Broken Belt Switch Kit is an OEM replacement part for Whirlpool dryers. It is an assembly that includes a microswitch and bracket installed to monitor the dryer drum belt status. The broken belt switch plays an important safety role by automatically stopping the dryer if it detects the drum belt breaking or slipping off the motor pulley during a cycle. The kit includes a switch, actuator lever, screws, and wire terminals.

Causes of a bad broken belt switch can include wear and tear over time, electrical malfunctions, or physical damage from a broken belt or other internal issues. Ensuring the switch is functioning correctly is crucial for the safe and efficient operation of the dryer.

Symptoms of a broken or failing switch include: 

• The dryer failing to shut off if the belt breaks during operation
• Inability to diagnose belt issues through error code displays  
• Intermittent stopping or variance in belt tension detection

This genuine Whirlpool switch replacement is also compatible with Kenmore, Maytag, Jenn-Air, and KitchenAid dryer models.

This burner tube channels the gas-air mixture to the burner and includes an adjustable air shutter to set proper combustion. Replacing a damaged assembly helps restore reliable ignition, stable flame, and consistent heating performance.

• Directs the fuel/air mixture from the gas valve to the burner port
• Integrated adjustable shutter regulates primary air for proper flame
• Helps maintain efficient heat output and reliable burner operation
• Failure can present as no or intermittent heat, burner that lights then goes out, yellow/lazy flame, or soot

• Disconnect power and shut off the gas supply; allow the appliance to cool before servicing
• Access the burner compartment and transfer any clips/brackets from the original tube
• Note the current shutter position; after installation, adjust for a steady blue flame
• After reassembly, leak-test gas connections with a soap solution and verify burner operation

This stationary drying rack sits inside the dryer drum to dry items flat without tumbling. It replaces a missing or damaged rack so you can properly dry sweaters, shoes, and other items that shouldn't rotate in the drum. What it does:

• Provides a stable, non-rotating surface inside the drum for flat-drying
• Allows airflow to dry items that should not tumble (e.g., sweaters or shoes)
• Restores the dryer's rack-dry capability when the original rack is missing or broken
• Typical symptoms: rack is cracked/warped, won't sit securely, or you need to dry items flat

• 1 drying rack

• Unplug the dryer before installing
• Open the door and position the rack so the rear support engages at the back of the drum and the front rests in the door opening
• Ensure the rack is level and secure before loading items evenly
• Do not run standard tumbling cycles with the rack installed; remove it when finished

This hinge retainer plate secures the appliance door hinge to the cabinet or door, keeping alignment and smooth operation. Replace a bent, stripped, or missing plate to stop hinge wobble and help the door close and seal properly.

• Anchors the door hinge and distributes load to prevent shifting
• Maintains proper door alignment and gap for smooth opening/closing
• Helps prevent door sagging, rubbing, or poor gasket sealing
• Typical symptoms include a loose hinge, wobbly door, or door not closing flush

• Disconnect power and support the door before removing any hinge fasteners
• Mark hinge locations to preserve alignment during reassembly
• Install the plate in the correct orientation; transfer any spacers/shims in original order
• Tighten fasteners evenly, then verify door alignment and gasket seal

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

This bearing ring is a small, low-friction spacer used in the dryer's drive system to let rotating components spin smoothly and quietly. Replacing a worn ring helps reduce drag, eliminate squeal, and protect related parts. What it does:

• Provides a bearing surface between a rotating wheel/pulley and its bracket
• Helps maintain smooth belt tracking and consistent tumble
• Reduces friction and wear on the belt and pulley/roller
• Common symptoms of wear: squealing/chirping while running, intermittent drum start, drag or burning-rubber smell

• 1 bearing ring

• Disconnect power; for gas dryers, also shut off gas supply
• Access the drive system; release belt tension and remove the affected pulley/roller as required
• Note the order/orientation of spacers, washers, and clips; install the new ring in the same position
• Hand-rotate the assembly to ensure free movement before reassembly and testing

This factory sensor provides critical feedback to the control so your appliance can adjust operation and protect components. Replacing a failed sensor restores accurate readings and helps eliminate erratic cycles and nuisance error messages. What it does:

• Monitors operating conditions and sends a signal to the main control
• Helps regulate timing, heating, and other functions based on real-time data
• A failing sensor can trigger error codes or stop a cycle prematurely
• Intermittent faults may cause unusually long/short cycles or inconsistent results

• 1 sensor

• Disconnect power before servicing to avoid electrical shock
• Access and mounting vary by model; refer to your unit's service information
• Transfer any brackets, seals, or screws from the original part if required
• Handle wiring connectors carefully; avoid pulling on the wires

This lint screen grille covers the lint filter opening inside the dryer drum. It supports the lint screen and provides a smooth surface at the opening to prevent snags, restoring proper fit and safe airflow. What it does:

• Supports and aligns the lint screen so it sits flush in the opening
• Shields the blower intake and keeps fabrics from contacting internal parts
• Provides a smooth edge to help prevent clothes from snagging or fraying
• Typical failure signs: cracked or missing grille, broken tabs, lint screen not seating properly, clothes catching near the lint opening

• 1 lint screen grille

• Disconnect power before servicing
• Open the dryer door and remove the screws securing the existing grille
• Lift out the old grille, position the new grille, and secure it with the existing screws
• Reinstall the lint screen and verify it slides smoothly and sits flush

The Lint Screen Door is an OEM replacement part for Whirlpool dryers. It is responsible for covering the lint screen area and protecting the inner components of the dryer drum. The lint screen door allows for easy access to clean out lint buildup after each load.

Over time, the door can suffer from wear and tear due to regular handling or accidental impacts. A faulty lint screen door can lead to improper lint trapping, which might cause airflow issues and potential fire hazards.

Symptoms of a bad lint screen door include:

• Difficulty opening or closing the door smoothly
• Gaps or openings that allow lint to bypass the screen
• Warping or misshapen door that no longer fits properly

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes missing or becomes damaged, it could cause the machine to vibrate more and seem louder.Nuts are made from metal and are built to last a long time. However, there can still be issues that arise. In some cases, the nuts might go missing if they become loose and the machine is moved. They could also corrode over time and need to be replaced. The replacement of the nut is typically a fast and simple repair.The nut is a genuine OEM replacement part sourced from the manufacturer. It can work with washers, dryers, and combo machines, and is compatible with models from Whirlpool, Kenmore, Maytag, and Roper. The part is sold individually. Owners may want to have several on hand.