Mh614oxkq-1 Parts

The Charcoal Filter is an OEM part for Whirlpool microwaves. This filter is designed to remove cooking odors and smoke from the air circulated through the microwave's venting system. It is especially important in over-the-range microwaves that recirculate air rather than venting it outside. The filter measures about 12 inches wide by 6 inches deep. This is a 2 Pack.

Causes of a bad charcoal filter can include saturation from grease and odors over time, blockage from accumulated debris, or deterioration of the filter material. Regular replacement is necessary to maintain effective air filtration and proper microwave performance.

Symptoms of a bad Charcoal Filter include:

• Persistent cooking odors lingering in the kitchen
• Reduced ventilation efficiency
• Smoke not being properly filtered during cooking
• Noticeable decrease in the microwave's air circulation

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

15 Amp, 125/250 Volt. Package of 2. Switches have 3/16 inch terminals.

This is a Whirlpool microwave magnetron. The microwave magnetron is one of the main components that control the heating function in the appliance. If a microwave has suddenly stopped heating but is still turning on normally, the problem could be the magnetron. Use a voltage tester to confirm whether this part is causing the problem. This component is made for installation in a microwave and oven combo where the microwave doubles as a vent hood. To replace this part, begin by unplugging the appliance and removing it from above the oven. Two people will be needed for this repair. This part requires exposure to highly sensitive electrical parts that could cause severe injury.This is a genuine OEM replacement part sourced directly from the manufacturer. This part is compatible with Whirlpool, Magic Chef, Amana, and Maytag appliances.

Color: chrome. Size: 7 5/8 x 5 inch. For charcoal grease filter use 4359331.

Replace a worn or misaligned interlock with this microwave door interlock assembly. It aligns and supports the door switches so the control accurately senses a fully closed door, restoring safe, reliable operation.

• Interfaces with the door latch hooks to actuate the safety door switches
• Ensures the microwave only runs when the door is fully closed
• Useful when the original interlock is cracked, loose, or out of alignment

• Disconnect power before service; microwaves can retain dangerous high voltage even when unplugged
• Access is typically behind the control panel; over-the-range units may need to be taken down for service
• Mount securely and verify the door latch hooks smoothly actuate the switches
• After reassembly, test door closure and start/stop operation before regular use

The Mount-Cabinet is an OEM part for Whirlpool microwaves. This part securely attaches the microwave to surrounding cabinetry, ensuring stability and safety in your kitchen setup. The Mount-Cabinet provides a firm hold, reducing the risk of movement or shifting that could lead to damage or operational issues.

Causes of a bad Mount-Cabinet can vary, including the natural wear and tear over time, improper installation leading to undue stress on the mount, or physical damage from external forces. 

Symptoms of a bad Mount-Cabinet include:

• The microwave becoming loose from its cabinet mounting
• Visible wear or damage to the mounting parts
• Increased noise or vibration during operation, indicating a lack of stability

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Microwave glass turntable tray. Color: clear. Measures about 13 inches in diameter.

This magnetron capacitor is the microwave high-voltage capacitor that helps supply the magnetron with the pulse of energy needed to produce heat. Replacing a failing capacitor restores normal heating performance and reduces arcing or loud humming. What it does

• Stores and releases the high-voltage pulse required by the magnetron so the microwave can generate heat.
• Prevents unstable magnetron operation that can cause weak or no heating.
• Common symptoms of a failing capacitor: oven runs but doesn't heat, intermittent heating, loud buzzing/humming, or visible arcing inside the cavity.
• A failed capacitor can also cause blown internal fuses or tripped circuits.

• One capacitor.

• Disconnect power and verify the appliance is completely de-energized before servicing.
• Capacitors can hold dangerous charge; discharge the capacitor safely with an insulated tool.
• Use the exact replacement part and follow the appliance service manual for routing and connections.

The Screw is an OEM part for Whirlpool microwaves. It is responsible for securing various parts of the microwave together. This screw ensures a tight and secure fit for parts and helps maintain the structural integrity of the microwave, preventing any loose or rattling parts.

A bad microwave screw can occur due to wear and tear, accidental damage, or misplacement during maintenance or repairs. If you notice symptoms such as loose or wobbly components, difficulty in opening or closing the microwave door, or abnormal noises while the microwave is in use, it may be time to replace this part.

Symptoms of a bad microwave screw include:

• Loose or wobbly components
• Difficulty in opening or closing the microwave door
• Abnormal noises during operation

Restore your Whirlpool microwave by replacing the faulty or missing microwave screw with this genuine OEM part.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This electrical safety fuse opens the circuit when a short or overcurrent occurs. Replacing a blown fuse can help restore power after the root cause is corrected, protecting controls and wiring from further damage.

• Protects the appliance by interrupting power during overcurrent or short-circuit events
• When open/blown, the appliance may be completely unresponsive
• Helps prevent damage to control boards and wiring during faults
• Often fails after a component shorts or a power surge occurs

• Disconnect power to the appliance before servicing
• Use a multimeter to test the fuse for continuity; replace only if open
• Install a fuse with the exact same rating and form factor as the original
• If the new fuse blows again, stop and diagnose the underlying fault; consider service for high-voltage systems

Color: Black. For biscuit order 98008169. For white order WP98008544.

This mounting bracket secures a designated component to the appliance frame, keeping it properly positioned and stable. Replacing a bent or broken bracket restores support and helps eliminate looseness, vibration, and misalignment during operation.

• Anchors the specified part to the chassis or panel
• Maintains proper alignment and clearances for reliable performance
• Helps prevent vibration, rattling, or shifting during use
• Common signs of failure: bent or cracked bracket, loose or misaligned components, new rattling noises

• Disconnect power and allow any hot surfaces to cool before servicing
• Note the original bracket's orientation and fastener locations for accurate reinstallation
• Transfer and tighten existing hardware securely without overtightening
• After installation, verify the supported part is secure and properly aligned

Refresh your microwave's appearance and door alignment with this white outer door frame. It replaces a cracked, warped, or discolored front frame, providing a clean factory look and proper support for the handle and inner door components. What it does:

• Forms the visible front trim of the microwave door
• Provides mounting points for the door handle and screws
• Helps keep door components aligned for smooth opening/closing
• Common symptoms: cracked/broken frame, loose handle area, misaligned door trim, cosmetic damage/discoloration

• White outer door frame

• Disconnect power before servicing; microwaves can retain dangerous voltage—do not access internal circuitry
• Remove the door and place it on a padded surface to prevent scratching
• Transfer the handle, screws, and any clips from the old frame to the new one
• Reassemble carefully to avoid damaging the inner glass and door choke/gasket

This replacement screw secures appliance panels, brackets, or internal components to keep them tight and aligned. Replace a missing, stripped, or damaged fastener to restore a solid, rattle-free fit and reliable operation.

• Fastens parts to the cabinet or frame to prevent movement
• Replaces missing, stripped, or corroded hardware that can cause looseness, vibration, or noise
• Helps correct gaps or misalignment after service
• Maintains proper support for covers, trims, or brackets

• Disconnect power; shut off gas/water if applicable before servicing
• Match screw length and location to the original position
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace damaged clips/inserts before installing the new screw

This replacement screw secures appliance components and panels in their proper position. Replacing worn, stripped, or missing hardware restores a tight fit, reduces vibration or rattles, and helps maintain safe, reliable operation per the manufacturer's design. What it does:

• Fastens panels, brackets, or assemblies where specified in the model's parts diagram
• Replaces missing, rusted, or stripped hardware
• Helps eliminate looseness, rattling, or vibration
• Restores secure alignment of mounted components

• 1 screw

• Disconnect power and shut off water/gas before servicing.
• Verify the exact location in your model's parts diagram and replace screws one at a time to maintain alignment.
• Use the correct driver/bit; start threads by hand to avoid cross-threading and do not overtighten.
• Inspect mating holes/clips for damage; repair or replace related hardware if threads are compromised.