Whirlpool Adg 954/1 Parts

This lint filter traps lint and fibers as air moves through the dryer, helping maintain proper airflow and drying performance. Replace a damaged or missing screen to reduce lint buildup inside the machine and along the vent.

• Captures lint and debris during the drying cycle to protect the blower and venting
• Helps maintain airflow for consistent drying results and temperature control
• Reduces lint redepositing on clothes and around the door opening
• Replace if the mesh is torn, the frame is warped/cracked, or if you notice longer dry times or excess lint inside the drum

• Disconnect power before servicing
• Remove the old screen and vacuum out the lint chute/housing; inspect and clean the exhaust vent as needed
• Insert the new filter and ensure it seats fully and flush—do not operate the dryer without the filter in place
• Run a short test cycle to confirm proper airflow at the exhaust

This push button switch mounts in the appliance's control panel and sends an electrical signal to the control when pressed. Replace a worn or sticking switch to restore dependable button response and function activation. What it does:

• Panel-mounted switch that closes its contacts when pressed to signal the control
• Restores reliable front-panel input for starting or selecting a function
• Helps address no response or intermittent response when the button is pressed
• Replaces switches with loose action, sticking, or heat-discolored/burned terminals

• 1 push button switch

• Disconnect power before servicing to avoid electrical shock
• Access the console/control panel to reach the switch
• Note wire positions (take a photo) and transfer connectors one at a time; ensure firm, fully seated terminals
• Secure the switch in the panel (nut/clip as applicable), verify button action, then reassemble and test

This limit thermostat monitors dryer temperature and opens the heating circuit if temperatures climb too high, helping protect the appliance and laundry. Replacing a failed thermostat restores reliable heat and safe temperature control. What it does:

• Monitors temperature at the heater/blower housing and opens at its limit to prevent overheating
• Helps maintain safe drying temperatures during normal cycles
• Common symptoms of a failed thermostat: no heat or intermittent heat, dryer runs too hot/overheats, or cycles end early due to overheating

• 1 limit thermostat

• Disconnect power and, if applicable, shut off gas before servicing
• Access the thermostat location per your model (typically on the heater housing or blower duct), remove mounting screws, and note wire positions
• Transfer wires to the new thermostat and mount it flush for proper sensing
• After reassembly, clear lint and verify venting/airflow to prevent repeat overheating

The Thermal Fuse is an OEM part for Whirlpool dryers. This part prevents the dryer from overheating by cutting off power to the heating element if the dryer exceeds a safe temperature. It helps protect the appliance and home from potential fire hazards caused by overheating.

Causes of a bad thermal fuse can include lint buildup restricting airflow, a malfunctioning thermostat, or excessive load causing the dryer to overheat.  

Symptoms of a bad thermal fuse include:

• Dryer not starting
• Dryer not producing heat
• Dryer shutting off mid-cycle
• No power to the dryer despite other electrical components functioning

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This 3-position fabric selector switch is the control behind the knob that lets you choose the fabric setting on your unit. Replacing a worn switch restores positive detents and ensures your selection is recognized instead of ignored or stuck.

• Provides three selectable fabric settings to tailor operation
• Routes the chosen setting to the timer/control
• Typical symptoms: no response when changing settings, intermittent selection, or being stuck on one mode
• Physical clues of failure: loose/no detent feel, broken shaft, or heat-discolored terminals

• Disconnect power before servicing
• Access the control console; remove the knob and retaining hardware to free the old switch
• Photograph/label wire positions and transfer each lead to the same terminals on the new switch
• Reassemble and test all three positions for proper engagement

This lint filter captures lint and fibers from the drying airflow to protect the blower and vent path. Replacing a damaged or missing screen helps maintain airflow, reduce lint buildup, and keep drying performance consistent.

• Traps lint and debris as air circulates through the dryer
• Helps maintain proper airflow and drying efficiency
• Replace if mesh is torn, frame is warped/cracked, or the filter won't seat fully
• Common symptoms: longer dry times, lint on clothes or around the door, or a filter that pops out

• Disconnect power; for gas models, also shut off the gas supply
• Remove the old filter from the lint opening and vacuum any lint from the housing
• Insert the new filter fully so it sits flat and seals properly
• Never operate the dryer without the lint filter installed

10 - 16 x 1/2

Specs: 10-16 x 1/2 inch.

Size: 8 x 1/2 ab.

This seal kit restores a proper water-tight barrier in the washer's drive area to prevent leaks and protect bearings and motor components on 1992-and-newer units.

• Seals the drive shaft/tub interface to stop water migration
• Helps prevent bearing and motor damage from moisture
• Common leak symptoms: water under the washer, rust streaks at center post, noisy spin from moisture intrusion
• May also address oil/water contamination around the transmission area

• Disconnect power and water; move the washer to a stable, level work area
• Removal of agitator, inner tub, and drive components is typically required
• Inspect shaft and mating surfaces; clean and lightly lubricate as specified by service literature
• Use proper drivers/press tools; do not hammer seals into place

Kit contains 2 pads, 1 right glide, 1 left glide, and instruction sheet. Support brace no longer included.

Considered a crucial part of the dryer, the blower fan assembly is the part that pulls in air from outside and then circulates that air in the drum to ensure clothing gets dry. After the air is moved around the drum, it is then moved through the exhaust vent. This part is located on the motor shaft and is made of durable plastic. Regular use can lead to wear and tear or damage to this component. If this occurs, the air in the dryer may not dry the clothing. In this case, the blower fan assembly will need to be replaced.If the blower fan assembly needs to be replaced, first the dryer should be unplugged from power. Take the cabinet top off and remove the front panel on the appliance. Take out the drum, remove the motor clamp, and loosen the blower fan so it can be removed. Take it out and replace it with the new blower fan assembly.The blower fan assembly is designed to be used with dryers manufactured by Amana and Speed Queen. It is sold as an individual part. This is an authentic OEM replacement part that is sourced directly from the manufacturer.

This drive motor and pulley assembly powers the belt-driven system to rotate the drum or tub. Replacing a weak or seized motor restores consistent rotation and reliable cycle performance on compatible 120V/60Hz models. What it does:

• Drives the belt that turns the drum or tub for wash/spin or tumble
• Provides correct 120V/60Hz operation for North American units designed for this spec
• Helps address symptoms like humming with no start, drum/tub not turning, belt not moving, or burning/motor smell
• Replaces a worn pulley to improve belt tracking and reduce slippage or squeal

• 1 motor and pulley assembly

• Disconnect power before servicing; for gas units, also shut off gas supply
• Relieve belt tension, note routing, and transfer wiring/connectors from the old motor
• Align the pulley and set proper belt tension; rotate by hand to verify free movement before restoring power

This part is a motor clamp. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or broken motor clamp on certain makes of indoor appliance models. Motor clamps are essential for properly securing the drive motor on various types of indoor appliances such as washers, dryers, and refrigerators. Without the use of a motor clamp, the drive motor is free to move around or become detached. This can easily cause serious damage to the equipment and prevent proper functionality. Proper tools are needed to replace this part and appropriate safety measures should be adhered to when working on any type of equipment. For accurate information on how and where to install this replacement motor clamp, specific manufacturer diagrams should be referred to.As an authentic replacement part, this motor clamp can be used on multiple different models of washers, dryers, refrigerators, and washer/dryer combos manufactured by Kenmore, Maytag, Whirlpool, and Amana. Please note that this motor clamp is a genuine part made of high-quality materials and is sold individually.

Sturdy metal door strike that mates with the latch/lock on your machine's cabinet. It keeps the door closed and engages the door switch so cycles can start and run without nuisance stops.

• Interfaces with the door latch/lock mechanism to secure closure
• Engages the door switch/interlock so the appliance can start and continue running
• Restores proper door alignment and latch feel after wear or bending
• Typical symptoms: door won't latch or pops open; unit won't start/run; intermittent stopping mid-cycle; visible damage to the strike

• Unplug the appliance (and shut off gas to gas dryers) before servicing
• Remove the existing strike and retain mounting hardware; note orientation
• Install the new strike in the same position; tighten screws and verify alignment
• Close the door to confirm smooth latching and proper operation

This door seal replaces a worn or damaged gasket around the oven door, creating a tight barrier between the door and the front frame. A fresh seal helps the appliance heat efficiently and maintain steady cooking temperatures. What it does:

• Seals the gap between the door and oven frame to minimize heat loss
• Helps the oven preheat faster and hold set temperatures more consistently
• Replace if the gasket is torn, brittle, flattened, or frayed
• Common signs include heat escaping around the door edge and longer cook times

• 1 door seal

• Disconnect power and allow the oven to cool completely before beginning
• Open the door and carefully remove the old seal, noting its routing and attachment points
• Clean the mating surface to remove debris for a proper seal
• Install the new seal evenly without stretching; ensure all ends and anchors are fully seated