Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Secures the control console to the washer cabinet. Replace if missing, stripped, or rusted to eliminate panel wobble and restore a tight, stable fit.
THIE REPAIR WAS ON A WHIRLPOOL TOP LOAD WASHING MACHINE At first I suspected the leak was from the pump because I had replaced the pump 2 times over 10 years. This time with the cabinet removed and filling the tub with water, I saw water running down one of the steel support arms that go under the tub, so I was guessing that it was coming from the tub seal. I had to use a jumper wire to bypass the Lid Switch so the water would drain. Several months before I had this issue with the water leaking... Read more
Fix washer rattling noise or loose cabinet with this retaining clip. Secures cabinet to back panel. Easy snap-in installation takes 10 minutes or less.
After looking at several YouTube videos, we decided we could attempt to fix this ourselves. We found the easiest video to follow from Appliance Parts, and ordered the clips and lid switch assembly (the clips we had to replace because we goofed that one ourselves). The parts came within a couple of days. The repair took a little over 1/2 hour only because we had to re-do some steps because my husband was over anxious and did some things without reviewing the video. Overall, it was a very... Read more
Loud rattling or loose agitator during wash? This clip secures the agitator assembly to eliminate noise and restore proper back-and-forth motion. Quick DIY fix.
Found that by manually spinning agitator one direction it seemed free, but spinning counterclockwise it seemed to stick a little. Pulled dispenser and agitator and found the agitator washer hole was oval rather than round. Replaced the agitator washer and the washer seems to sound normally for now. Not sure if the new agitator washer will eventually grind down due to non-circular action from the transmission, or if the agitator and clip will keep the transmission centered long term. Should... Read more
If your washer agitator spins freely or won't move clothes, the upper agitator may be worn. Often replaced with agitator dogs. Video guide available.
I had replaced the Agitator cams a couple of times already due to my brother-in-law overloading the machine which stripped the teeth off of the cams. I also noticed the agitator seemed to 'wobble' and made 'knocking' noises quite a bit. I reviewed the video on the Appliance Parts Pros web site, disassembled the agitator and cleaned everything up, which helped a little, but not enough. Figuring the agitator itself was worn out also, I looked up and ordered all the parts for the upper agitator on... Read more
Spacer that maintains proper alignment between the washer cabinet and top panel. Replace if broken, cracked, or missing to restore stability.
Replacement timer knob for washers. Installs on the control panel to adjust wash cycle settings. Replace if cracked, broken, or won't stay attached.
Replaced fill level switch and tube and replaced timer knob Read more
Rubber inlet hose that connects your washer to the water supply. Replace if cracked, leaking, or worn. Standard 5-foot length with included washers.
Replaced flow meter and control valve Read more
Structural bracket that secures the rear panel to the washer chassis. Replace if cracked, broken, or missing to restore proper alignment and cabinet stability.
In the end, with a new coupler. But I relearned old lessons the hard way. The washer is in a rental unit and the tenant complained of no spin. My first intuition was that the coupler failed again because I bought a cheaper one elsewhere a couple of years ago and not the brand name available here at AppliancePartsPros. But we’ll come back to that. Lesson #1: Verify the symptoms firsthand. I dug in right away, popped out the motor and the coupler appeared okay. When I spun it by hand, it turned... Read more
Fix loud grinding noise or basket won't spin issues. This washer transmission gearcase drives the agitator and basket rotation. Moderate DIY repair.
Symptoms: Machine was spinning and spitting a dark colored oil in a circular pattern on the floor under the machine. No strange noises, just messy. Researched issue, Gear-case bad, seal deteriorated and not preventing water from entering gear-case. The additional cam, belt etc I had replaced due to the amount of oil and transmission residue attached to them. Ordered parts, EVERYTHING parts-wise that is needed is included in gear-case package. **NOTE: You WILL need to get a whirlpool spanner... Read more
Washer motor shield deflects water, lint, and debris away from the drive motor. Replace if cracked or missing to prevent motor damage. Simple install.
Washer won't spin or agitate? A faulty drive motor causes humming noises and stopping mid-cycle. This direct replacement restores drum rotation.
This was a tricky one to figure out. The Maytag Centennial MVWC400XW4 would fill and wash, then stop before spin cycle or would not complete the spin cycle. We had to manually move the dial to rinse & spin, etc. to get it to finish a load. This technique worked but it definitely became a pain to do and at the time we didn't notice how much longer the machine took calibrating a wash load. I called Sears initially thinking I really didn't want to mess with this and they came out. They... Read more
Fix washer shaking and excessive vibration during spin cycles. This leveling leg locking nut secures adjustable legs to stabilize your machine.
Replaced 2 springs and brackets. Also replace rear legs and front legs and re leveled. Works fine. Read more
Mounts the washer top panel to the cabinet frame. Replace if screw is stripped, rusted, missing, or damaged during cabinet disassembly and repair work.
I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair... Read more
Washer thrust ring acts as a bearing spacer between the outer tub and basket drive, controlling end-play and reducing friction. Replace when worn to restore smooth, quiet operation and prevent premature wear.
Purchased parts from your site and did a self repair. Excellent quality , speedy delivery and easy to install. Now our 13 year old washer works as good as new. Read more
Rubber grommet that cushions the motor mount stud on your washer. Replace if cracked, worn, or missing to properly secure the motor to the mounting plate.
Replaced dog ears. Read more
Fix washer not spinning or loose cam driver with this wire retaining ring. Secures basket drive components to prevent shifting. DIY-friendly repair.
Based on recommendation to replace the clutch if clothes aren't spinning dry enough, I ordered a new clutch. Upon disassembly, I observed no Ring Wire/C-Clip and that the bearing appeared worn. Where did the clip go? Well, the bearing wore down such that it wore out the clip and bearing up to the sleeve of the shaft. Knocked out the old bearing, tapped in the new and was done. I disassembled the brake shoes but believe you can get the bearing in and out without doing so. Not a bad job, just... Read more