Thermal Coupler Parts

This fixed, non-adjustable thermostat switches at approximately 140°F to control or limit temperature in the appliance. Replacing a fatigued thermostat restores accurate temperature regulation and helps prevent underheating, overheating, or erratic cycling.

• Senses temperature and changes state near 140°F to switch a circuit as designed
• Helps regulate heaters, fans, or act as an over-temperature protector
• Failure can cause no heat/low heat, runs too hot, or inconsistent cycling
• May prevent a fan or heater from turning on or off when expected

• Disconnect power and allow components to cool before servicing
• Verify the temperature rating and terminal style match the original
• Note wire positions; transfer any mounting clips/insulators from the old part
• Ensure firm, clean contact with the mounting surface; avoid overtightening or flexing the disc

This cycling thermostat regulates on/off heat cycles to maintain consistent operating temperature. Replacing a failed thermostat restores proper temperature control and helps protect the appliance from overheating or underheating during normal operation.

• Senses internal temperature and opens/closes contacts to control the heating circuit
• Helps prevent overheating; supports stable, repeatable heat cycling
• Common failure symptoms include no heat, overheating/shutting off too soon, or longer-than-normal run times
• Electrical component—failure may be intermittent before complete loss of function

• Disconnect power (and gas supply, if applicable) before service
• Note wire locations; transfer connectors one at a time to the new thermostat
• Mount firmly against the mating surface for accurate temperature sensing
• After installation, verify proper operation and temperature cycling

This turbidity sensor detects how clear the dishwasher's wash water is so the control can adjust cycle time, rinses, and water changes. Replacing a faulty sensor helps restore proper cleaning performance and normal cycle lengths.

• Monitors soil level/clarity of the wash water
• Signals the control to extend or shorten wash and rinse phases as needed
• Helps optimize water use while maintaining cleaning results
• Failure symptoms can include unusually long or short cycles, poor cleaning, repeated draining/refilling, or cycles that won't advance

• Disconnect power and turn off the water supply before servicing
• Pull the dishwasher out as needed; access the sensor from the base area
• Place a towel to catch residual water; release the locking tab or twist-lock, unplug the connector, and install the new sensor fully seated and locked
• Restore power/water and run a test cycle; check for leaks

This cycling thermostat regulates the dryer's heat by sensing exhaust air temperature and switching the heater on and off. Replacing a faulty thermostat restores consistent drying performance and helps prevent underheating or overheating.

• Monitors dryer air temperature and cycles the heating element or gas burner to maintain the proper range
• Helps prevent overheating that can trip safety limits
• Failure can result in no heat, low heat/long dry times, or heat that doesn't cycle correctly
• May cause intermittent shutdowns due to temperature issues

• Disconnect power; if gas, also shut off gas supply before servicing
• Thermostat is typically mounted on the blower housing or exhaust duct
• Note/transfer wires to the same terminals and secure the thermostat with existing screws; ensure it seats flush to the housing
• After replacement, clean lint buildup and verify proper vent airflow to avoid repeat temperature problems

Color: brown. Each prong measures about 4-1/2 inches from the center.

This dishwasher sensor assembly contains the thermistor that monitors wash-water temperature and sends readings to the control. Replacing a faulty sensor restores accurate heating and cycle timing for consistent cleaning and to prevent temperature-related interruptions. What it does:

• Measures wash-water temperature via an NTC thermistor
• Sends a resistance signal to the control to manage heater operation and cycle timing
• Helps maintain target temperatures for proper cleaning performance
• Common failure symptoms include no heat or overheating, long/short cycles, temperature-related errors, or poor cleaning/drying

• Disconnect power at the breaker and shut off water before servicing
• Access the sump area from the bottom; you may need to pull the dishwasher forward for clearance
• Expect some residual water—protect the area with towels
• Seat the sensor fully in the sump opening, reconnect the harness, and run a test cycle to check for leaks and proper heating

The Electrode is an OEM replacement part for Whirlpool dryers. It is responsible for detecting the moisture levels in your laundry during the drying cycle, allowing the dryer to automatically adjust the drying time and temperature. It helps prevent over-drying or under-drying of your clothes, saving energy and protecting them from potential damage.

A bad electrode can occur due to wear and tear, damage, or a buildup of debris or lint. If you notice symptoms such as clothes taking longer to dry, the dryer shutting off prematurely, or inconsistent drying results, it may be time to replace the moisture sensor bar electrode.

Symptoms of a bad electrode include:

• Clothes taking longer to dry than usual
• The dryer shutting off prematurely
• Inconsistent drying results, with some items remaining damp

Repair your dryer by replacing the faulty or damaged electrode with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

The Turntable Coupler is an OEM part for GE microwaves. This component connects the turntable motor to the microwave's glass tray, enabling the rotation of the tray during cooking. By ensuring even heating and cooking of food, the turntable coupler plays a vital role in the microwave's overall performance.

Causes of a bad turntable coupler can include wear and tear from frequent use, physical damage from heavy or uneven loads on the turntable, or breakage from accidental impacts.

Symptoms of a bad Turntable Coupler include:

• The turntable not rotating
• Uneven cooking or heating of food
• Grinding or clicking noises when the turntable attempts to move
• The glass tray being unstable or slipping off the coupler

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This safety thermostat is a temperature-sensitive switch for dryers. It monitors internal heat and opens the circuit if temperatures climb too high, helping prevent overheating. Replacing a failed thermostat restores proper heat control and safe operation.

• Monitors dryer temperature and cuts power to the heater if the limit is exceeded
• Helps protect against overheating and heat-related shutdowns
• Common symptoms of a failed or tripped thermostat: no heat or intermittent heat, dryer running too hot, or cycles ending early due to overheating
• Overheating or repeated trips often indicate restricted airflow—inspect venting and lint paths

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the thermostat location per your model's service information
• Note wire positions and transfer them one at a time; mount the thermostat flush to its mating surface
• After installation, clear lint and verify proper airflow through the exhaust and vent

This 155°F-rated electric dryer thermostat monitors and controls drum temperature. It cycles the heating element to maintain proper heat so loads dry consistently while helping protect the appliance from overheating.

• Regulates dryer temperature on electric models
• Controls heater cycling to maintain proper drying temperatures
• Failure may cause no heat or weak heat
• May lead to overheating or longer-than-normal dry times

• Disconnect power before servicing
• Access the thermostat for your model, note wire positions, and transfer connectors one at a time
• Mount the thermostat flat and secure for proper thermal contact
• Reassemble, restore power, and test a cycle for proper heating

Comes with 4 supports. Color: chrome.

This dishwasher turbidity sensor measures how dirty the wash water is and reports to the control. Replacing a faulty sensor can restore proper cycle times and cleaning performance for consistent results.

• Monitors water clarity/soil level during the wash
• Sends feedback to the control to adjust cycle length, rinses, and heating
• Failure can cause very long or very short cycles
• Can trigger sensor-related fault indications

• Disconnect power at the breaker and shut off water before servicing
• Access the sensor from the bottom near the sump; remove the toe panel if needed
• Unplug the wire harness; release the locking tabs or twist-lock to remove; avoid touching the optical window
• Inspect and reuse the existing seal/retainer if in good condition; seat fully and check for leaks after reassembly

This support secures and stabilizes a mating component inside your appliance, helping restore proper alignment and fit. Replace a damaged or missing support to stop wobble, sagging, or misalignment.

• Provides structural backing to keep the attached part level and in place
• Helps eliminate rattling, shifting, or uneven gaps
• Replace if cracked, deformed, or missing
• Symptoms can include loose or sagging parts, poor alignment, or difficulty reinstalling shelves/panels

• Disconnect power (and shut off water, if applicable) before service
• Remove the affected shelf/drawer/panel to access the support
• Transfer and reuse any model-specific fasteners or clips
• Seat the new support fully and check alignment before reassembly

This internal-bias thermostat controls exhaust temperature in your dryer, cycling the heat on and off to maintain proper drying temperatures. Replacing a failed thermostat can restore consistent drying performance and help protect the dryer from overheating shutdowns.

• Monitors exhaust air temperature and opens/closes the heating circuit to regulate heat
• Provides the bias function used by automatic cycles for correct temperature control
• Failure symptoms can include no heat or low heat, long dry times, overheating or high-limit trips, and inconsistent cycling temperatures
• Helps prevent thermal cutoffs caused by restricted airflow or faulty temperature regulation

• Disconnect power before servicing; for gas models, also shut off the gas supply
• Access location is typically on the blower/exhaust housing; note wire positions and transfer one at a time
• Ensure the thermostat mounts flush for proper sensing; tighten screws securely
• After replacement, verify good airflow and clear venting to prevent repeat failures

The Microwave Coupler is an essential component for maintaining your Samsung microwave's performance. This genuine OEM part ensures a precise fit and reliable connection, compatible with a variety of Samsung microwave models. Crafted from high-quality materials, the coupler provides durable support, enhancing the stability and functionality of your appliance. By replacing a worn or damaged coupler with this genuine OEM part, you can restore your microwaveGÇÖs efficiency and prevent potential operational issues. Installation is straightforward, making it an ideal choice for DIY repairs and helping you save time and money. The Microwave Coupler not only ensures your microwave operates smoothly but also extends the lifespan of your appliance. Trust in this high-quality part to deliver dependable performance and improve your overall kitchen experience.

The Thermostat is an OEM component specifically designed for GE dryers. As a key component responsible for regulating heat, this thermostat plays an important role in the drying cycle. It monitors and controls the temperature of the dryer, ensuring clothes are thoroughly dried without being overheated or damaged. 

Causes of a bad thermostat can include wear and tear over time, exposure to high heat levels that degrade electronic components, or damage from moisture or impact. 

Symptoms of a bad thermostat include: 

• Inefficient or prolonged drying times 
• The dryer not heating up properly
• Fluctuations in temperature
• The dryer not starting or functioning correctly

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.