Line Line Mover Flywheel Key Parts

I watched your video and had it fixed in less than 1 minute! Read more

• Lid or door won't close

This was a super-easy repair. You have to line up the spring so that it sits on the bumps inside the magnet holder and the door, then you have to line up the tabs on the magnet holder so they will slide into the slots on the door. Then you just push it in. Repair took less than a minute. Read more

I pulled the dryer away from the wall and unplugged it. Then I used a 5/16 nut driver and removed the 2 screws in the bottom front panel and pulled it off. Next I removed the 2 5/16 screws holding the front door panel and pulled it down far enough to disconnect the wires for the light and the wires on the door switch. Then , using a putty knife I popped the springs holding the top and control panel then pulling the top up and resting it against the wall. Now I started my repair by laying on... Read more

• Will not tumble

Repair went well, replaced the pulley wheel, belt, rear drum bearing. Had an issue after replacement with the dryer stopping after ~5mins or so when running with heat. Fluff cycle would run fine. Details: The lock nut on the pulley wheel didn't feel tight enough so i tried to crimp it back on the pulley arm. It then became way too lose. I had to replace it with a plastic washer I had in my toolkit. That fit snug and seems to work fine. I also added some grease to the pulley shaft under... Read more

Was going to order 4 new wheel & spindle sets, then saw you could get just the wheel for 1/3 the cost, so I ordered those. Then in the frequently ordered other items I saw the idler wheel assy. So I ordered one of those also. Glad I did, it was in worse shape than any of the wheels which still seemed to spin freely after I got all the hairs and crap off them. Anyways, went by the video step by step. Pretty straightforward. Have a good vacuum handy, I’m surprised that it used to dry at all... Read more

• Door won't close

There is a video on youtube that talks about how to disassemble the electronic component out of the control board so I really won't go into that part of it. This disassembly of the control board will need to take place before you can even get started taking the gray piece out of the console to replace it. Be careful not break off the little tips behind the control knob, don't force it, it does come apart easily and there is an easy way to do it, that is also on youtube. This is where the... Read more

Unscrewed door latch and replaced it with the new door latch (1-2 min). Unscrewed outer plate from door lock assembly. Removed door lock assembly from its outer plate and unplugged wiring. Replaced with new door lock assembly, plugged back in, tightened some screws, double-checked alignment between latch & lock assembly was good and the project was done. Incredibly easy and saved about $150 not having a repair tech come out to fix it. Read more

• Lid or door will not open
• Won't start
• Lid or door won't close

Just removed the old and put on the new,simple.On this Fridgidare washer you should lift the door as you close it which should make the striker last.. Read more

I ran a diagnostics check on the washing machine and came up with the error code E47 -Board thinks the door PTC circuit is open in spin. The washer thought the door was open and would not finish the spin. I was left with a washer full of very wet clothes. This repair was SO extremely easy. I only needed to uses a pair of needle nose pliers and a screw driver. It took less than 10 minutes, start to finish. Now the new door lock assembly registers correctly and my clothes are completely... Read more

Replaced pulley and belt. Read more

Replaced the door latch/lock assembly. Read more

Ordered parts from Appliance Parts Pros and replaced them.Works like new Read more

Replaced door lock switch. Read more

In the past, I replaced some electronic components on our gas dryer, the solenoid and the electronic ignitor, but the rest of the dryer looked more difficult to repair if needed in the future. I was wrong. I went unto AppliancePartsPros.com and watched some repair videos on dryers like mine that make big thumping sounds while drying. This happened when I googled my dryer model number in an attempt to find out is capacity, because I wanted our new dryer to have the same capacity. I found out... Read more

Ordered a new seal, and replaced it with a new one freezer works great now. Read more

The part is so new no video so I went onto a similar part and watched video that got me about 80%. Then, called and customer service sent me a service Manual but this still was not specific so I broke the old to get it out and in the process figured out how to do it correctly. So I installed the last bit of it which was the bezel through the machine top by myself correctly. So you take the old one out by pushing out to the right from the bottom side using a screw driver for leverage. It will... Read more