Module Dispenser Parts

Made by Bosch. Common program control module for Bosch dishwashers SHU53/68. NOTE The manufacturer has redesigned the cover and indicator lights. Lights may be covered by the plastic case. You may have to remove the square covers over the indicator lights if needed. The same case is used for 6 and 8 indicator light models. They also no longer use the red bulb indicator lights, small surface mounted lights are used instead. If you require the Jumper Wire that goes with certain models, the part number is 00167782.

An ice auger rotates inside the freezer's ice bin to move cubes to the crusher and out the dispenser chute. Replacing a worn or broken auger restores consistent dispensing and helps eliminate jams and grinding from a slipping spiral.

• Advances ice through the bin toward the crusher/dispenser chute
• Works with the crusher assembly to deliver cubed or crushed ice based on the selector
• A stripped or cracked auger may result in little/no ice dispensing while the motor runs
• Damage can cause ice jams, uneven dispensing, or grinding noises from the bin

• Unplug the refrigerator; remove and empty the ice bin, allowing any frost to thaw
• Wear cut-resistant gloves—crusher blades and sheet-metal edges are sharp
• Disassemble the crusher/blade stack and note the exact blade/spacer order
• Transfer the blade stack, bushings, and hardware to the new auger; reassemble and confirm smooth rotation before reinstalling

This OEM replacement part is an ice container for refrigerators. The ice container is the plastic bucket that holds the ice that is made by the icemaker. Over time, an ice container can become damaged due to excessive wear and tear. If the ice container is cracked or broken to the point where it can no longer hold ice, it will need to be replaced.To replace the ice container, start by unplugging the refrigerator. Once unplugged, proceed to open the freezer door. Locate the two mounting screws that attach the ice container to the icemaker. Once found, proceed to unthread the screws to remove the old container. After pulling the old container out, slide the new one in place and fasten the mounting screws that secure it to the icemaker. This genuine replacement part is sourced directly from the manufacturer and is sold individually. It is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand refrigerators.

The electronic control board is the appliance's main control module. It interprets inputs from the user interface and sensors, then powers and times key components to run each cycle. Replacing a failed board restores reliable, predictable operation.

• Coordinates cycle sequencing and powers components through onboard relays
• Receives signals from switches/sensors and manages overall operation
• Common failure symptoms: unresponsive controls or no power
• Won't start, stops mid-cycle, or won't advance through a cycle
• Intermittent operation, flashing lights, or fault/error codes tied to the main control

• Disconnect power at the breaker before servicing; verify the unit is de-energized
• Use ESD protection; handle the board by the edges to avoid static damage
• Photograph/label wiring and move connectors one at a time to the matching terminals
• After installation, run the appliance's diagnostic/test cycle to confirm proper operation

This replacement door latch engages the strike/catch to keep the door securely closed so the appliance can operate. A worn or broken latch can cause door-closed detection issues, doors that pop open, or cycles that won't start.

• Secures the door by engaging the strike/catch for a positive close
• Ensures door/interlock switches register "door closed" so the unit can run
• Helps maintain a reliable seal and reduces interruptions mid-cycle
• Common symptoms: door won't latch or pops open; appliance won't start; door/latch-related error messages

• Disconnect power to the appliance before servicing
• Note the latch orientation; transfer any original screws/clips as needed
• Align the latch with the strike and tighten fasteners securely
• Close and open the door several times to verify smooth engagement before testing operation

This dishwasher detergent dispenser assembly stores detergent and releases it at the correct time in the wash cycle to ensure consistent cleaning results. Replacing a worn dispenser restores reliable soap release and helps improve wash performance.

• Holds detergent and opens when signaled by the control
• Common symptoms: detergent cup won't open, soap left in the cup after cycle, broken dispenser door/latch

• Disconnect power to the dishwasher before servicing
• Open the door and remove inner-door screws to access the dispenser
• Release locking tabs, remove the old dispenser, and clean the sealing surface
• Seat the new dispenser evenly, reinstall screws, restore power, and run a test cycle

This automatic ice maker assembly forms and releases ice cubes into your refrigerator's bin, restoring steady ice production when the original unit fails. Install to resolve no-ice or incomplete harvest issues and keep ice ready when you need it.

• Freezes water in its mold and ejects cubes into the storage bin during each cycle
• Pauses production when the bin is full to prevent overflow
• Coordinates with the refrigerator control and water valve for proper fill and harvest timing
• Common symptoms include: no ice production, won't cycle/harvest, cubes jammed, or leaking/overfilling near the ice maker

• Disconnect power and turn off the water supply before servicing
• Remove the ice bin; unmount the old ice maker and unplug its connector; mount and connect the new assembly
• Align the fill tube with the ice maker's fill cup to prevent leaks
• Restore power and water; allow several hours (up to 24) for normal ice production to resume

Color: Black
The Dispenser Cover is an OEM part for Frigidaire refrigerators. The dispenser cover protects the dispenser components from accidental spills, dust, or impact while also adding an elegant styling element to the refrigerator exterior.

Causes of a bad dispenser cover can include cracks or breaks from repeated opening and closing of the door over time. Normal wear from daily use can also cause looser fits or gaps.

Symptoms of a bad dispenser cover include:

• Cracks, breaks or missing pieces of material
• Improperly seated or loose fit when installed
• Spills or condensation leaks into dispenser mechanisms
• Affects the clean appearance of the refrigerator

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Detergent Dispenser Box is an OEM part for LG washing machines. Housed within the washer door, this compartment delivers precise amounts of detergent at the optimal time. 

Symptoms of a bad dispenser box include:

• Cracks or breaks compromising the dispenser structure
• Detergent leaking or residual buildup outside of the box
• Failure to fully dispense detergent during wash cycles 

Causes of failure can include plastic fatigue from years of opening/closing the washer door. Repeated impacts may also damage internal mechanisms. This OEM LG part can also be used on Kenmore/Sears appliances. 

The Icemaker is an OEM replacement part for Whirlpool bottom-mount and side-by-side refrigerators. 

Causes of a bad icemaker can include failures in electronic controls, cold plate freezing, or mechanical components that inhibit harvest functions.

Symptoms include: 

• Failure to produce ice or reduced ice output
• Jammed or broken ice delivery mechanism  
• Dripping or leaks from the icemaker system
• Error codes appearing on control panels

This OEM Whirlpool replacement icemaker is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: White

The Electronic Control is an OEM part for Whirlpool dishwashers. It is the main circuit board that regulates all electrical functions and directs components during cycles. Sensors throughout the dishwasher relay information to the control board, which processes data and generates output signals to control mechanisms such as wash motor, heater and dispensers.

Causes of a bad electronic control include failures from long-term, continuous usage overload, issues due to power fluctuations or surges that disrupt circuitry.

Symptoms of a bad electronic control include: 

• Fault codes displayed 
• Lights, buttons or other functions malfunctioning
• Inability to start cycles or advance through phases
• Irregular cycle times, temps or abnormal sounds  

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and Kenmore models. 

This replacement dishwasher detergent dispenser stores detergent and releases it at the correct time in the cycle, while also controlling rinse-aid dosing. It restores reliable cleaning performance when the original dispenser is damaged, leaking, or won't open.

• Holds detergent securely and opens on command during the wash cycle
• Meters rinse aid during the final rinse to help reduce spots and film
• Seals to the inner door at the dispenser opening to help prevent leaks
• Typical symptoms: detergent left in cup, dispenser door won't latch/pop open, rinse aid not dispensing or leaking, visible cracks or warping

• Disconnect electrical power and turn off water supply before servicing
• Open the door and remove inner-door panel screws to access the dispenser
• Unplug the wire connector(s), release retaining screws/tabs, and remove the old dispenser
• Clean the door cutout, seat the new gasket evenly, secure the dispenser evenly, reconnect wiring, and run a leak check

This replacement dispenser drawer restores smooth operation and proper dispensing of detergent, bleach, and fabric softener in your washer. It helps prevent leaks and residue when the original drawer is cracked, warped, or difficult to open and close. What it does:

• Holds and meters detergent, bleach, and fabric softener into the wash at the correct time
• Helps ensure additives mix with water and flow into the tub, not onto the cabinet front
• Direct replacement for drawers with broken handles, cracks, or swelling
• Common symptoms: leaking at the drawer area, poor dispensing, leftover detergent, or a stuck drawer

• Includes: 1 dispenser drawer assembly

• Disconnect power and turn off water before servicing
• Pull the drawer out fully and depress the release tab to remove
• Transfer any removable siphon caps or inserts from the old drawer
• Clean the dispenser housing channels, then slide in the new drawer and run a test cycle to check for leaks

This ice storage bin holds the ice made by your refrigerator's icemaker and keeps it contained and easy to access in the freezer. Replace a cracked or warped bin to prevent spills, jams, and poor seating.

• Collects and stores ice cubes produced by the icemaker
• Keeps cubes contained to minimize spills and stray frost
• Slides/seats on the designated rails or shelf area in the freezer
• Common signs of failure: cracks, broken tabs, bin won't seat or slides out, ice falling into the freezer

• Unplug the refrigerator or disconnect power; switch the icemaker off
• Pull the old bin straight out; empty and clean the area
• Slide the new bin in until fully seated; restore power and turn the icemaker back on

This electronic control board kit is the appliance's central controller, coordinating inputs and powering key components. Replacing a failed board restores proper operation, responsive controls, and reliable cycle management. What it does:

• Manages timing and power to motors, valves, heaters, fans, and other loads
• Interprets sensor and user-interface signals to start, run, and end cycles correctly
• Common failure signs: dead or unresponsive controls, cycles that won't start/finish, repeated error codes, or intermittent operation
• Helps address issues caused by power surges or board damage

• 1 electronic control board (module)

• Disconnect electrical power to the appliance; turn off gas/water if applicable
• Use ESD protection and handle the board by its edges
• Photograph wiring; transfer connectors one at a time and match any jumpers/DIP-switch settings from the original board
• Restore power and perform any model-specific tests or programming per OEM instructions