Line Chef Line Mover Switch Parts

The Door Switch Kit is an OEM part for Whirlpool dryers. This kit includes a door switch that plays a crucial safety and operational role in the dryer's function. It ensures that the dryer operates only when the door is firmly closed, preventing the machine from running with an open door, which could pose safety risks and inefficiency in the drying process.

The causes of door switch failure often include physical damage from slamming the dryer door, wear and tear over time, or electrical issues such as short circuits. 

Symptoms of a faulty Dryer Door Switch include:

• The dryer not starting when the door is closed 
• The dryer continuing to run when the door is opened, which poses a significant safety hazard.
• Unusual noises from the switch area 

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This rotary switch mounts behind the control knob and reads your selections on the user interface. Replacing a worn switch restores accurate, reliable knob response so the appliance recognizes the chosen setting and relays it to the control board.

• Detects the position of the selector knob and sends the appropriate signals to the main control
• Enables choosing programs/settings using the front knob
• Failure may cause unresponsive or erratic selection, settings not changing when the knob turns, or a no-start if no selection is registered
• Typically located on the back of the control panel behind the knob

• Disconnect power before servicing
• Remove the knob and access the control panel to reach the switch
• Release locking tabs or screws; transfer the wire connector in the same orientation
• Align the shaft correctly with the knob and test operation before reassembly

The Push to Start Switch is an OEM part for Whirlpool dryers. It is responsible for initiating the drying cycle when pressed, sending an electrical signal to start the dryer.

You should replace this push to start switch if it becomes defective. Causes of a bad switch can include electrical failures, physical damage from repeated use, or internal wear over time.

Symptoms of a bad push to start switch include:

• The dryer not starting when the button is pressed
• The need to press the button multiple times to start the dryer
• No response or clicking sound when the button is pressed

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: For square top push to start switch, use part number W10156101.

The Door Switch is an OEM part for GE dryers, designed to ensure the dryer does not operate when the door is open. This safety feature is crucial for preventing accidents and ensuring the appliance operates efficiently and safely. The switch signals the dryer's control system about the status of the door—if it's open or closed—thereby allowing or preventing the start of a drying cycle. 

Causes of damage to the door switch often include mechanical wear from repeated use, accidental damage from loading or unloading, or electrical issues such as short circuits. 

Symptoms of a bad Door Switch include:

• The dryer not starting when the door is closed 
• The dryer continuing to run when the door is opened
• Unusual noises or the dryer stopping mid-cycle

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Lid Switch Assembly is an OEM part for Whirlpool washing machines. It ensures that the washer stops spinning when the lid is open, providing safety and preventing water spillage.

Causes of a bad lid switch assembly can include wear and tear from regular use, exposure to moisture leading to corrosion, or physical damage from slamming the lid or improper handling.

Symptoms of a bad lid switch assembly include:

• Washer not starting or stopping mid-cycle
• The machine not draining or spinning
• Error codes related to lid issues
• The washer continuing to operate with the lid open

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Water Level Switch is an OEM part for Whirlpool dishwashers. It monitors and regulates the water level inside the dishwasher during wash cycles, ensuring the correct amount of water is used for optimal cleaning performance.

The water level switch can fail due to several reasons, such as electrical issues, mechanical wear over time, or damage from water exposure. Blockages or debris can also interfere with its proper functioning.

Symptoms of a bad water level switch include:

• The dishwasher not filling with water
• Overfilling or flooding inside the dishwasher
• The dishwasher stopping mid-cycle or not progressing through cycles
• Error codes related to water levels

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Surface Element Control Switch is an OEM part for Frigidaire electric ranges and cooktops. It is a critical component that controls the operation of the surface heating elements, allowing you to turn them on and off, and select the desired heat settings.

Symptoms of a faulty Surface Element Control Switch include:

• Inability to turn on or control the surface heating elements
• Inconsistent or erratic heat output from the elements
• Elements not cycling on and off properly or staying on continuously
• Heating elements not responding to temperature adjustments

Causes of a bad Surface Element Control Switch can include electrical faults, physical damage, or wear and tear over time due to frequent use and exposure to high temperatures. 

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Interlock Switch is an OEM replacement part for GE dishwashers. It is an electronic sensor located inside the dishwasher door that detects when the door is securely closed. 

Symptoms of a bad Interlock Switch include:

• The dishwasher will not start a cycle even with the door closed  
• Error messages related to the door being open displayed
• Failure to advance through cycle selections
• Inconsistent or unreliable door closure sensing

Causes can be normal wear and tear over extended use. Moisture exposure inside the dishwasher environment may also contribute to switch malfunction over time.

This OEM part is also compatible with some Hotpoint, RCA and Kenmore branded dishwashers. 

The Dispenser Switch is an OEM replacement part for GE refrigerators. This switch is crucial for the functionality of the water and ice dispenser, as it activates the dispensing mechanism when the user presses the lever or button. The switch ensures that the refrigerator dispenses water or ice on demand, providing convenience and ease of use.

Over time, the dispenser switch can wear out or become damaged due to frequent use, exposure to moisture, or electrical issues. This can result in the switch failing to activate the dispenser properly, impacting the performance of the refrigerator's dispensing system.

Symptoms of a bad dispenser switch include:

• The water or ice dispenser not responding when the lever or button is pressed
• Intermittent or inconsistent dispensing of water or ice
• The dispenser working only occasionally or requiring excessive pressure to activate
• No audible click or feedback when pressing the dispenser lever or button

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Infinite Heat Switch Kit is an OEM part for GE ranges and cooktops. This kit is essential for controlling the temperature of the burners on your range or cooktop, allowing you to adjust the heat level from low to high. 

Causes of damage to the infinite heat switch can include normal wear and tear from frequent use, electrical issues such as short circuits or power surges, and physical damage from cleaning or impact. 

Symptoms of a bad Infinite Heat Switch include:

• Burners not heating to the desired temperature, either staying too hot or not getting hot enough.
• The burner not turning on at all, indicating a possible failure in the switch's electrical contacts or circuit.
• Inconsistent cooking temperatures, where the burner cycles on and off too frequently or not often enough, affecting cooking performance.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Door Switch is an OEM part for Frigidaire microwaves, designed to ensure the appliance operates safely by signaling when the door is securely closed. This switch is critical for preventing the microwave from running if the door is open, a key safety feature that protects users from exposure to microwave radiation.

Causes of a bad Door Switch can include mechanical failure due to normal wear and tear from repeated opening and closing of the microwave door. 

Symptoms of a bad Door Switch include:

• The microwave not starting or heating when the door is closed.
• The appliance continuing to operate when the door is opened.
• Intermittent operation or sudden stopping during use.
• Displaying error messages related to the door or switches.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Range Triple Burner Element Switch is essential for controlling the heat on each of your rangeGÇÖs three burners. This reliable switch ensures precise temperature regulation, allowing you to cook your meals evenly and efficiently. Crafted as a genuine OEM part, it guarantees compatibility with a variety of Samsung range models, ensuring a secure fit and seamless operation. By replacing a faulty switch with this genuine OEM part, you can restore full functionality to your range without the hassle of incompatibility issues. The Range Triple Burner Element Switch enhances your cooking experience by providing consistent performance and easy control, making it simple to adjust the heat as needed. Designed for durability and longevity, this switch offers a cost-effective solution for maintaining your Samsung range over time. Installation is straightforward, allowing you to quickly get back to cooking without unnecessary delays. This switch is engineered to meet the high standards of Samsung appliances, ensuring that every component performs reliably over time. Its robust construction minimizes the risk of overheating and other common issues, providing you with peace of mind in the kitchen. Trust in the quality and reliability of this genuine OEM part to keep your kitchen running smoothly and efficiently. Whether youGÇÖre an everyday cook or a culinary enthusiast, the Range Triple Burner Element Switch is a vital component for optimal performance.

The Light Switch is an OEM part for Whirlpool refrigerators. This switch is responsible for controlling the refrigerator's interior light, turning it on when the door is opened and off when it is closed.

Symptoms of a failing refrigerator light switch include:

• The interior light staying on when the refrigerator door is closed
• The light not activating when the refrigerator door is opened
• Intermittent or flickering light due to a loose connection or faulty switch

Causes of light switch failure typically involve mechanical wear from repeated use, accumulation of dirt or debris that can interfere with the switch mechanism, or electrical issues such as short circuits.

This OEM part is also compatible with other brands manufactured by Whirlpool, including Maytag, KitchenAid, Jenn-Air, Amana, and others.

The Turn Start Switch is an OEM part for Frigidaire dryers. It is responsible for initiating the drying cycle when the switch is turned. This switch is a critical component that engages the dryer’s motor and starts the drying process, ensuring your clothes are dried effectively.

You should replace the turn start switch if it becomes faulty or unresponsive. Causes of a bad start switch can include regular wear and tear from frequent use, electrical issues, or damage due to excessive force or mishandling.

Symptoms of a bad turn start switch include:

• Dryer not starting when the switch is turned
• Intermittent starting issues
• The switch feeling loose or not engaging properly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Infinite Switch Top Burner Control is an essential component for your range, ensuring precise control over your top burners. This genuine OEM part is specifically designed for Samsung ranges, guaranteeing a perfect fit and seamless functionality. Crafted with high-quality materials, this control switch delivers reliable performance and enhances the overall efficiency of your appliance. Installing this genuine OEM part is straightforward, making it simple to replace a faulty or worn-out switch without any hassle. By choosing the Infinite Switch Top Burner Control, you ensure the durability and longevity of your range's controls, contributing to a safe and enjoyable cooking experience. Whether you're a home chef or looking to maintain your appliance, this top burner control switch is the perfect solution to restore your range's optimal performance.

The Whirlpool Infinite Switch is an OEM part for Whirlpool ranges. Whirlpool electric ranges. This switch controls the multiple heat settings of the large element, allowing the user to select their desired cooking temperature. It is an important electrical component that regulates burner heating cycles.

Symptoms of a bad infinite switch include:

• The element not heating up adequately or failing to maintain temperature
• Inability to select or change heat settings on the
• Burner operates intermittently or fails to heat properly

Causes of a bad infinite switch can include failure over many heating cycles. The electrical contacts within the switch may become corroded or deteriorate from repeated exposure to cooktop temperatures and cooking residue.

It is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore electric range models.