Kenmore Freezer 253.9284213 (2539284213, 253 9284213) Parts

I have used this freezer for ~ 10 years with no problems. We have noticed that frost started forming inside the freezer, so after research, the first step was to replace the gasket around the door. I ordered the part and replaced it, which took about 45 minutes. To replace, I would recommend unscrewing the screws around the existing gasket BUT DO NOT REMOVE THE SCREWS as that will take extra work. Just unscrew, and make sure the old gasket comes out of the track easily. To re-install,... Read more

Suspected it was the thermostat, since temperature stayed the same at multiple settings over a 24 hr period. There was only three components inside the freezer besides the evaporator, the fan was working, so I decided to just go ahead and replace the thermostat and defrost thermostat. Also replaced the defrost timer by the compressor, just to get all the old parts replaced with new. I had already replaced the compressor, so now I've pretty much have a new freezer. The new parts works great and... Read more

Ordered a new seal, and replaced it with a new one freezer works great now. Read more

• Noisy

1. After hearing a loud noise on the freezer side of unit about halfway up, I started investigating what it could be? My conclusion was evaporator motor or evaporator fan blade. One of the signs of this issue was a distinct change in sound when I opened the freezer door. I ordered a new motor and blade, not knowing exactly what it was. 2. I couldn't get water to dispense, so I changed the filter and that wasn't the problem. I ordered a water valve and crossed my fingers. These parts arrived... Read more

Replaced both The electrical board I found under the fridge was very easy to replace. The fan motor took a minute to bed puns and the biggest challenge was taking off/on the back panel to get to it. (By the way it was located in the freezer section. take drawers out to get to it. Read more

• Freezer too cold
• Freezer not defrosting
• Fridge runs too long
• Fridge too cold

My Frigidaire side by side refrigerator/freezer suffered a catastrophic failure. The symptoms were as follows: 1) Frig not cold 2) No Ice being made in the freezer section 3) Items at the back of the freezer were frozen but items on the door shelves would not freeze. The back of the freezer was cold but the closer you got to the door the warmer it got. After removing everything from the unit I saw that there was substantial ice buildup on back of the freeze, specifically around the vents,... Read more

Ordered light switch and it arrived the following day with standard shipping! That was FAST!! Removed old swich, installed new, only 2 wire switch, very easy. I was very impressed with the 1 day delivery Read more

Had a friend who is an appliance repair tech. Replace the evaporator, the heater coil, and the filter/drier. Parts were soldered together and the compressor was put under vacuum. Then, charged with 5 oz. of refrigerant. The freezer works great now! Read more

I determined that it was a problem that occurred during the defrost cycle by resetting the GFCI outlet and forwarding the defrost timer until the defroster came on. Once the defrosting began, the GFCI outlet would reliably trip. I took apart the shielding inside of the freezer and tested the defrosting without the heating element or the thermostat connected. Since that looked good, I tested for proper functionality of the thermostat by removing it, placing it in a working freezer, and checking... Read more

Quick touch up. The paint worked great. Packaged with a brush like nail poliish Read more

Replaced the fan and blade. Would have been easy except the mounting threads were different than the original Kenmore freezer came with. After a 14 mile round trip for 2 5/32 screws and washers, I had my freezer back. Included an improved wiring harness than the original. Read more

Removed the freezer shelves and back panel, evaporator coils were frozen with ice. Defrosted coil and removed defrost heater connectors, measured no continuity in the heater and ordered a replacement. Also discovered the aluminum retention strap was broken and the heater had slipped down in it's position, ordered and replacement strap. Re-installed new heater and strap per the video instructions, repair complete. Most difficult steps were drilling out the drain pan rivet and re-threading... Read more

I took it apart myself by just un-doing screws and taking it apart. Reversed the process to put it back together. Read more

Replaced the handle. Read more