5Ksb3bwh3 Parts

The KitchenAid Blender Drive Coupler is an OEM part for KitchenAid blenders. This part connects the blender's motor to the blade assembly.

Causes for issues with the drive coupler often involve overloading the blender, blending hard or frozen ingredients without sufficient liquid, or simply the natural degradation of the component over time.

Symptoms of a malfunctioning Blender Drive Coupler include:

• The blender's motor running, but the blades not spinning
• Visible wear or damage to the coupler's teeth
• Unusual noises during operation, indicating a misalignment or damage

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This 60-oz blender jar assembly replaces a damaged or worn jar so you can safely blend full batches again. It provides a secure container for ingredients and a proper fit on the base for consistent, mess-reducing performance. What it does:

• Provides a 60-ounce container for blending, mixing, and pouring
• Interfaces with the blender base for efficient circulation of ingredients
• Helps prevent leaks when the jar and sealing surfaces are intact
• Typical symptoms of a bad jar: cracks, leaks, clouding, or an unstable fit on the base

• One 60-oz blender jar assembly

• Unplug the blender before servicing
• Remove the old jar; if your model uses a separate blade/collar, ensure gaskets are properly seated during reassembly
• Wash the new jar before first use and confirm it seats flat on the base
• Fill with water and test for leaks before blending food

The Lock Jar is an OEM replacement part for Whirlpool Blenders. Securing the blending jar safely during operation, the lock enables smoothie and food preparation.

Causes of a faulty blender locking jar include normal wear of locking tabs and ridges that hold the jar in place through years of use. Exposure to liquid residue over time may potentially compromise lock performance.

Symptoms of a bad locking jar include:

• Potential tipping or detachment of jar during blending posing spill and injury risks
• Inability to achieve proper suction seal jeopardizing blend consistency
• Lock failure releasing sharp blade assembly with attached jar interior

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.

This replacement coupling links and seals wash-system components so pressurized water reaches the spray arms. Replacing a cracked or worn coupling restores cleaning performance and helps prevent drips at the connection point.

• Provides a secure, watertight connection within the dishwasher wash system
• Helps deliver proper water flow to the spray arms
• Failure symptoms can include poor cleaning, spray arms not turning, a loose/detached feed tube, or leaks at the connection
• Replace if the coupling is cracked, deformed, or stripped

• Disconnect power and shut off water before servicing
• Remove dish racks and access the coupling at the manifold/feed-tube area per your model
• Inspect existing seals/O-rings and replace if worn
• Seat and lock the coupling fully; run a short cycle to check for leaks

This 8-32 x 5/8 screw replaces missing or damaged hardware specified by the manufacturer to secure panels, brackets, and internal components in your appliance. Restores a tight, rattle-free fit to help prevent vibration and misalignment.

• Provides the correct 8-32 thread and 5/8-inch length where specified
• Secures sheet-metal panels, brackets, and internal assemblies
• Replaces missing, stripped, or corroded screws
• Symptoms include loose or rattling panels, misaligned parts, or hardware that won't stay tight

• Disconnect power; shut off gas before servicing
• Support panels/components while removing or installing hardware
• Start threads by hand to avoid cross-threading; tighten only until snug
• Match the original screw's location and orientation for proper fit

This replacement seal keeps liquids and food particles out of the blender motor housing to protect internal components and help prevent leaks. Fits the motor assembly where the shaft passes through the housing. What it does

• Seals the motor shaft opening to help prevent liquid from entering the motor housing.
• Reduces risk of motor damage or shorting caused by leaks into the base.
• Helps stop leaking at the blender base or around the blade assembly when worn.
• Replace if the seal is cracked, flattened, swollen, or shows visible wear.

• Always unplug the appliance before disassembly and removal of the jar or motor housing.
• Remove the blade and jar assembly per the service diagram to access the shaft seal; inspect mating surfaces and replace damaged components.
• Ensure the new seal is seated evenly around the shaft and in its groove; do not force or over-stretch the seal.
• After reassembly, run a short water test (with the unit unplugged from any direct water source) to check for leaks before normal use.

A general-purpose 6-20 screw used to secure panels, brackets and small components on Whirlpool appliances. Replaces stripped or missing fasteners to restore a snug fit and reduce rattling or loose parts. What it does:

• Secures appliance panels, trim, brackets and internal components in original mounting locations.
• Stops panel movement, vibration noise and loose connections caused by missing or corroded screws.
• Fits the OEM 6-20 thread designation used on multiple Whirlpool assembly points.
• Sold individually for spot repairs and small part replacements.

• Disconnect power or gas supply to the appliance before starting any repair.
• Use the correct screwdriver or bit to avoid stripping the head; tighten until snug but do not overtighten.
• Replace like-for-like; stop and verify the correct fastener for the mounting point.
• Check the appliance's parts diagram for the exact screw location and orientation.

This factory replacement screw fastens appliance components securely. Use it to replace lost, stripped, or corroded hardware and restore a snug, rattle-free fit and proper alignment of panels and assemblies.

• Secures panels, brackets, and internal components to their mounting points
• Replaces missing or damaged fasteners to maintain correct alignment
• Helps eliminate vibration and rattling caused by loose hardware
• Restores the original fit with OEM-matched threads and dimensions

• Disconnect power and shut off water or gas supplies before servicing
• Use the correct driver bit that matches the screw head to avoid stripping
• Replace one fastener at a time to keep parts aligned
• Tighten snugly; do not overtighten to prevent stripped threads or cracked plastic

The Blender Drive Coupling is an OEM replacement part for Whirlpool built-in blender bases. It connects the blending container to the electric drive motor below.

Causes of malfunction include wear from years of operation. Repeated blending torque stresses the components in alternating directions, eventually leading to fatigue and loosening. Accidental impacts can also damage the precision coupling pieces.

Symptoms of a failing blender drive coupling involve: 

• Inability to power blend jars or containers  
• Excessive vibration or grinding noises during use
• Loose, wobbly, or freely spinning attachments
• Reduced blending performance functionality  

This authentic Whirlpool replacement is compatible with some KitchenAid models.

A replacement shim that restores correct spacing and alignment between appliance components to reduce vibration and rubbing. Helps ensure parts fit together properly after repair or during reassembly. What it does:

• Provides precise spacing and alignment between panels, brackets, or assemblies
• Helps reduce noise and vibration caused by parts rubbing or sitting out of alignment
• Used when reseating or replacing components to maintain proper clearances
• Small, simple part that supports reliable operation of surrounding hardware

• Disconnect power to the appliance before starting any repair
• Install in the same location and orientation as the original shim; retain any removed fasteners
• Use basic hand tools; avoid forcing parts—check alignment as you tighten
• Refer to the manufacturer's service manual or parts diagram for exact placement and torque guidance

Factory replacement jar for select small appliances. It restores a clean, intact vessel for everyday use, helping prevent leaks and spills when the original container is cracked, chipped, warped, or missing. What it does:

• Serves as the primary container for contents during operation
• Interfaces with the appliance base and lid for safe, spill-resistant use
• Replaces jars that are cracked, leaking, or have a broken/loose handle
• Helps restore proper seating and a secure fit

• 1 jar

• Disconnect power and allow any moving parts to stop before servicing
• Remove the old jar; clean and dry mating surfaces on the base and lid
• Transfer any reusable components (such as lid or seals)
• Seat the new jar fully and leak-test with water before first use

This replacement appliance foot restores stable, level support for your appliance so it sits flush and reduces rocking or vibration. Use it to replace a worn or damaged leveling foot that prevents proper balance. What it does:

• Provides adjustable support so the appliance can be leveled on uneven floors
• Reduces rocking, excessive vibration, and movement during operation
• Helps correct uneven door/Drawer alignment caused by a collapsed or missing foot
• Restores proper weight distribution for safer operation

• Disconnect power and water before working on the appliance
• Tilt or raise the appliance per the manufacturer's guidance; use blocks or an appliance jack for safety
• Thread the foot into the mounting insert and adjust height until the appliance is level; hand-tighten and verify stability
• Do not exceed recommended force when tightening; inspect for secure fit and proper clearance