Ge Belt Parts

First, I did a search based on the problem I had with my model of dryer. The model number was on the door frame and was visible when I opened the dryer door. The problem was, when I pressed the button to start a dryer cycle, I heard a clicking noise and the indicator text changed to "Drying", but I could not hear or see the dryer drum turning. The search led me to a page that indicated my problem was usually one of 3 common causes. 1. Faulty door switch 2. Broken Drum drive belt 3. burned out... Read more

• Will not tumble
• Won't start
• Noisy

My GE dryer from the late 80's/early 90's was squealing when it would start up, belt or bearing I was thinking. I found a manual online that covered my model and I watched a video on this site that showed me how to take it all apart, mine was a bit different but the principles were the same. I took it apart and added some quick-disconnects to 2 wires so next time I can take the front panel off easily. When I got to the bearing it looked worn but not bad so I cleaned it and put it back. ... Read more

• Spins slowly
• Will not agitate

After researching the problem on this site, I realized that the most likely cause was a bad bearing contained in the shaft & tube assembly. Essentially, the tub seal failed & allowed water to travel down the shaft & into the housing containing the bearing. I confirmed this by pulling the front cover off of the unit & noticed some brown water pooled directly under the shaft & tube assembly. I followed the disassembly instructions on this site & it wasn't too bad but did take some time as pretty... Read more

• Burning smell
• Spins slowly
• Pumps but will not spin
• Noisy

Ordered new transmission, nut, split washer and spanner wrench to do the install. very straight forward fix after watching the video. spanner wrench is a must or the correct large socket with an impact driver. it was corroded on pretty well let the liquid wrench work for a while and then beat it off. approximately 2 hours to do to fix, spent some time cleaning stuff up also though. washer was 12 years old and debated scrapping it and getting a new one but then it would not match the dryer. ... Read more

• Will not tumble
• Won't start

Replaced rear bearing, upper and lower felts, drive belt. Have repaired dryer before for same problem years ago, knew what to do, on line diagrams helped to move memory. Cleaned all accumulated lint out of machine.Belt was changed only out of age.Looked good but thought to be on safe side. Read more

Replaced transmission and support assembly. Hub nut corrode on support, spanner wrench would not loosen. Had to use 1 11/16 deep socket and impact wrench to remove, basket would not com off support even after cleaning out and soaking with penetrant and using automotive air hammer to push out. I had to cut support plate in half with die grinder, cut bearing from shaft and punch out agitator shaft then use die grinder with carbide burr to cut basket shaft in two before basket would come off... Read more

The Dryer is 10 years old GE Front Load DPVH890JEMG. The drum would intermittently not rotate at the beginning of a cycle and occasionally would rotate but then start and stop throughout the cycle. I did not check error codes, but the windings on the motor were black. So it seemed reasonable that the motor was overheating and sending a signal to the control board to stop. There is one screw under the knob and 9 screws on the front to get inside. I decided to replace the bearings, capacitor,... Read more

I replaced the idler pulley assembly, the bearing plastic and the drive belt. While disassembled I cleaned the interior of the cabinet and lubricated the drum bearings with silicone after cleaning everything thoroughly. The dryer is now quiet and hopefully stays that way. Read more

Found the belt was thrown off. Reinstalled the belt and when doing so felt that the pulley was wobbling on the barrel shaft. Took the pulley off and noticed the inside of the pulley was worn badly and needed to be replaced. When received the new pulley and belt easily installed and was working like new. Read more

I replaced the drive belt using the video instructions on your web site. My dryer is in a stacked configuration, inverted with respect to your instructions with the motor above the drum instead of below it. During reassembly the drum got stuck when the pivot did not seat properly in its socket so the front couldn't be reassembled until I lifted the drum to reseat its pivot so the drum could move back into position allowing the front to be reassembled. The hight of the drum in the stacked... Read more

• Pumps but will not spin
• Will not agitate
• Burning smell

I replaced the broken drive belt first and noticed the drive pulley loose. The nut that had held it in place had backed off. This resulted in significant wear on the pulley hub. I just tightened it up and installed the belt. I noticed the belt had a tendency to change its position on the pulley depending on the direction of rotation. I was a bit concerned but decided to see what would happen. This fix lasted for about a week. The belt came off the pulley and broken again. I called a... Read more

The hardest part of this repair was determining where (controls, motor, belt or transmission) the problem was. I could see little pieces of rubber from the belt beneath the motor pulley, but the machine is 20 years old and some wear is to be expected. Since the belt was still intact and neither frayed or cracked and since I didn't know what the original dimensions were and since the machine was still able to agitate, I could only identify the belt as a possible source of the failure to... Read more

Order set of drum rollers. My dryer required four. As long as I was opening up the dryer, dryer, 10 years old, I wanted to replace all of them. Also ordered new belt for Sam reason. Found full manual online. Disassembled dryer, about 20 screws. Replaced rollers, although only one was squeaky. Put it all back together. Took about 3 hours. Read more

Openeded the control,took down the lid and replaced the belt. Read more